Snapper FLT19540RD, ELT2240RD, ELT19540RD Cutting Height Adjustment, Attaching a Trailer, Storage

Page 19

A

Figure 9. Raising & Lowering Mower

A. Mower Lift Lever

Cutting Height Adjustment

The mower lift lever (A, Figure 9) is used to lower the deck to cutting position and raise the deck to transport position.

To lower the deck, pull back slightly on the mower lift lever (A), push it to the left and slide it down. To raise the deck to transport pull up on the mower lift lever (A) and lock in notch to the right. Do not cut in transport.

Attaching a Trailer

The maximum horizontal drawbar force allowed is 280 Newton. The maximum vertical drawbar force is 160 Newton. This equates to a 250 lbs (113 kg) trailer on a 10 degree hill. Secure the trailer with an appropriately sized clevis pin (A, Figure 10) and clip (B).

Operating the Tractor

WARNING

Never store the unit (with fuel) in an enclosed, poorly ventilated structure. Fuel vapors can travel to an ignition source (such as a furnace, water heater, etc.) and cause an explosion. Fuel vapor is also toxic to humans and animals.

Storage

Before you store your unit for the off-season, read the Maintenance and Storage instructions in the Safety Rules section, then perform the following steps:

Disengage the PTO, set the parking brake, and remove the key.

Perform engine maintenance and storage measures listed in the engine owner’s manual. This includes draining the fuel system, or adding stabilizer to the fuel (do not store a fueled unit in an enclosed structure - see warning).

Battery life will be increased if it is removed, put in a cool, dry place and fully charged about once a month. If the battery is left in the unit, disconnect the negative cable.

Before starting the unit after it has been stored:

Check all fluid levels. Check all maintenance items.

Perform all recommended checks and procedures found in the engine owner’s manual.

Allow the engine to warm up for several minutes before use.

A

B

Figure 10. Trailer Weight Recommendations

A. Clevis Pin

B. Clip

17

Image 19
Contents Mfg. No Title Description HP Hydro TractorsPage Table of Contents Safety Rules & Information Operating Safety Slope Operation Safety Rules and InformationGeneral Operation Safety Rules & InformationIgnition System Safe Handling of Gasoline Service & MaintenanceCE Identification Tag Markings Identification NumbersTractor ID Tag Mower ID Tag Safety Decals Safety DecalsSafety Icons Decal Locations CE Safety IconsTransmission Release Headlights Control FunctionsThrottle Control ChokeFeatures & Controls Cruise Control Operation Parking Brake FunctionHour Meter Adding Fuel Safety Interlock System TestsGeneral Operating Safety Operational Safety ChecksOperating the Tractor Lift Lever Tractor Hitch Brackets Mower Deck Removal & InstallationRemoving the Mower Deck Muffler and surrounding areas may be hotInstalling the Mower Deck Catcher Removal & InstallationLock Lever Attaching a Trailer Cutting Height AdjustmentStorage Check Tire Pressure Maintenance Schedule & ProceduresRegular Maintenance Hood Removal and Installation Transmission MaintenanceTransmission Identification Grease Service Interval Every 25 HoursLubrication OilLubricate Rear Axle Shafts Service Interval YearlyServicing the Mower Blades Service Interval Every 100 Hours or As RequiredCheck Blade Timing Check Mower Blade TimingRecommended Engine Oil Check & Fill Engine OilChange Engine Oil Oil Drain Valve OperationChange Engine Oil & Filter Air Filter Service Air Filter & Pre-Cleaner ServiceAir Filter Removal & Installation Pre-Cleaner ServiceAir Filter Assembly Single Cylinder Models Latch Cover Spark Plug Gapping Replace Spark PlugRegular Maintenance Troubleshooting the Tractor TroubleshootingTroubleshooting the Mower Troubleshooting, Adjustment, & ServiceFuse Replacement Seat AdjustmentBrake Adjustment Battery ChargingAdjust PTO Clutch Window Adjustment Nut Feeler Gauge PTO Clutch AdjustmentTo avoid damaging belts. do not PRY Mower Belt ReplacementMower Blade Timing Arbor Drive Belt Replacement19.5 HP* Briggs & Stratton 22 HP* Briggs & StrattonK46 Maintenance Items Replacement Parts

ELT19540RD, FLT19540RD, ELT2240RD specifications

Snapper has established itself as a leader in the lawn care equipment industry, with its standout products like the Snapper FLT19540RD, ELT2240RD, and ELT19540RD. Each model comes equipped with a unique set of features, technologies, and characteristics that cater to various lawn care needs.

The Snapper FLT19540RD is a revolutionary lawn tractor designed for efficiency and versatility. It boasts a robust 19.5 horsepower engine, delivering reliable power for mowing, bagging, and mulching. One of the standout features of the FLT19540RD is its 40-inch cutting deck, which provides a wide cutting path, ensuring that large areas are mowed quickly and effectively. The deck can be easily adjusted to achieve different cutting heights, allowing users to maintain their lawns according to personal preference or seasonal requirements. Additionally, the tractor's hydrostatic transmission offers smooth and intuitive operation, enabling users to easily control speed and direction without the need for manual gear shifting.

On the other hand, the Snapper ELT2240RD is more compact and designed for residential homeowners who may have smaller lawns or tighter spaces to navigate. This model features a 22-inch cutting deck and a powerful 40-volt lithium-ion battery, which provides quiet operation and an environmentally friendly alternative to gas-powered mowers. The ELT2240RD is designed with user comfort in mind, incorporating an ergonomic handle and lightweight design, making it easy for anyone to maneuver around the yard. The battery life is impressive, allowing for extended runtime and quick recharging, making it a practical choice for homeowners who prioritize efficiency and sustainability.

Lastly, the ELT19540RD combines the best of both worlds. It features a 19.5 horsepower engine and a spacious 40-inch cutting deck, striking a balance between power and compact design. Its innovative design promotes better air circulation and clippings discharge, leading to enhanced mulching capabilities. The ELT19540RD is equipped with advanced safety features, including a safety switch that ensures the engine only runs when the operator is securely seated.

All three models exemplify Snapper's commitment to quality, innovation, and user-friendly design. They cater to various lawn care needs, whether for a large space or a more intimate garden, providing reliable performance while ensuring an efficient mowing experience. With Snapper, homeowners can be confident in their lawn care choices, enjoying beautifully maintained lawns with minimal effort.