Snapper EM250819BE, EM281019BE Service Annually, Engine, Fuel Filter, Every TWO Years

Page 18

Section 3 - MAINTENANCE

WARNING

DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure away from plug. Engine and components are HOT. Avoid serious burns, allow all parts to cool before working on machine. Fuel Filler Cap and Vent must be closed securely to prevent fuel spillage.

3.3SERVICE - EVERY 25 OPERATING HOURS 3.3.9. DIFFERENTIAL/CHAIN CASE - LUBRICATION 3. Check fill/level plug for damage. If signs of wear or cracks are visible, replace plug with new plug. See Figure 3.9.

4.To check lubricant in chain case, remove fill/level plug and look for lubricant on the internal components of the chain case. If no lubricant is visible, add "SNAPPER Transmission” grease as needed. See Figure 3.9.

AXLE

BOOTS

CHAIN

CASE

FILL/LEVEL PLUG

P.N. 1-1024

FIGURE 3.9

3.3.10.Check “MAINTENANCE SCHEDULE” Section of Engine Owner’s Manual for additional engine service.

3.4SERVICE - ANNUALLY

3.4.1.Perform all maintenance as specified in “MAINTENANCE SCHEDULE” Section of this manual.

3.4.2.ENGINE

Perform all maintenance as specified in Engine Owner’s Manual.

3.4.3. FUEL FILTER

Service fuel filter as instructed below, on COLD ENGINE ONLY!

IMPORTANT: To stop flow of fuel, tank may be removed from bracket and set on the floor so the fuel level will be below the filter. Refer to Section “REMOVING FUEL TANK”.

1.Remove hose clamps from fuel filter.

2.Remove fuel lines from filter. Discard filter.

3.Install new fuel filter. See Figure 3.10.

4.Reinstall fuel tank into bracket.

HOSE

CLAMPS

FUEL

FILTER

P.N. 1-4359

FIGURE 3.10

3.5EVERY TWO YEARS

In addition to regular maintenance, the following components of the Rear Engine Rider should be carefully inspected every two years for wear or damage. Replace worn or damaged parts with genuine SNAPPER replacement parts available from an authorized SNAPPER dealer.

3.5.1.All bushings and pivot areas.

3.5.2.Check both front wheel king pins.

3.5.3.Transmission shift lever and detent.

3.5.4.Clutch disc.

3.5.5.Clutch Yoke (See Figure 4.9).

3.5.6.Mower deck linkage and pivot areas.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents European Rear Engine Riding Mower Series Manual No -3121 I.R /20/99Important Safety Instructions Operation Table of Contents Introduction NomenclatureFamiliarization Decals / Symbols Lowest Traction Height CUT Clutch OPERATOR’S Seat Adjustment 2.2.1. Front to Rear Adjustment PRE-START Check ListStarting & Operation Engine Electric Start On NextStarting & Operation Engine Electric StartEngine Manual Start Starting & Operation 2.3.3. Mower Blade Wheel DriveStopping ENGINE, Wheel DRIVE, Blade 2.4.1. Engine Mower BladeCutting Height Adjustment Stopping ENGINE, Wheel DRIVE, Blade 2.4.4. Park BrakeDo not park machine on slopes Service After First 5 Hours Change Engine OIL Service Engine AIR Cleaner Check Mower BladeService After First 5 Hours 3.2.4. Check Blade Drive Belt Service Brake / Park BrakeBlade Brake Battery Fluid Level Service Every 25 Operating HoursClean Mower Deck Interlock SystemService Every 25 Operating Hours from previous Front Wheel Bearing LubricationRear Axle Bearing Lubrication Fuel Filter Service AnnuallyEngine Every TWO YearsStorage OUT of Season Removing Fuel TankEngine Adjustments & Repair Mower Drive Belt Adjustment for 25, 28 & 30 M ModelsBlade Brake Adjustment Mower Deck Adjustment Side-To-Side LevelnessMower Deck Adjustment Front to Rear Levelness 25 & 28 DecksFront to Rear Levelness 30 Decks Chain Case Clutch Yoke Cable Housing Spring Mower Blade Replacement 4.4.1. Blade Wear Limits Blade SharpeningBlade Drive Belt Replacement Belt ReplacementBelt Removal Battery Battery Removal Battery InstallationNEW Battery Preparation 1. Remove battery from carton Battery ServiceBattery Storage Battery TestingSnapper Rear Engine Rider Accessories Problem Probable Cause Corrective Action StopCutting Grass Loss Of TractionBlades Not Cutting ImproperlySubject Service Reference To be Performed PagesMAINTENANCE/REPLACEMENT Parts Maintenance Parts Year Limited Warranty Disclaimer of WarrantyService Notes Service Notes European Rear Engine Riding Mower Series

EM250819BE, EM281019BE specifications

The Snapper EM250819BE and EM281019BE are two advanced electric mowers that embody the latest innovations in outdoor power equipment. Aimed at both residential and commercial users, these models offer exceptional performance, efficiency, and user-friendly features to simplify lawn care.

The Snapper EM250819BE features a robust 20-inch cutting deck, providing the ideal balance between maneuverability and coverage. This mower is powered by a high-efficiency brushless motor, which not only extends the lifespan of the instrument but also delivers consistent power output, ensuring an even cut across various grass types. The EM250819BE offers multiple cutting height adjustments, allowing users to customize their lawn's appearance according to seasonal preferences and grass species.

Equipped with a 40V lithium-ion battery, the Snapper EM250819BE boasts an impressive runtime, enabling users to tackle larger yards without interruptions for recharging. The onboard LED battery indicator is particularly handy, allowing users to monitor battery levels easily and plan their mowing schedule without surprises. Additionally, the mower's lightweight design ensures easy maneuverability, making it less strenuous to operate for extended periods.

On the other hand, the Snapper EM281019BE brings a larger 28-inch cutting deck into play, perfect for those who need to cover wider areas quickly. Like its counterpart, this model features a brushless motor that ensures efficient operation and reduces maintenance needs. The EM281019BE also supports various cutting height settings for a tailored mowing experience.

One of the standout features of the EM281019BE is its self-propelled option, allowing users to navigate tougher terrains with minimal effort. This is complemented by enhanced traction control, making it ideal for slopes and uneven lawns. The model also includes a proprietary mulching feature, enabling grass clippings to be finely chopped and returned to the soil, thus promoting healthier lawn growth.

Both models are designed with user comfort and safety in mind. They come with ergonomic handles for better grip and reduced fatigue during extended use. Additionally, the easy-to-access safety features ensure that the mowers meet the highest standards of user protection.

In summary, the Snapper EM250819BE and EM281019BE represent a significant advancement in electric mowing technology, delivering performance, efficiency, and convenience in an environmentally friendly package. With their user-centric design and powerful features, they are excellent choices for anyone looking to achieve a beautiful lawn with less hassle.
Top Page Image Contents