Snapper EM250819BE, EM281019BE Chain Case Clutch Yoke Cable Housing Spring

Page 23

Section 4 - ADJUSTMENTS & REPAIR

WARNING

DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure away from plug. Engine and components are HOT. Avoid serious burns, allow all parts to cool before working on machine. Fuel Filler Cap and Vent must be closed securely to prevent fuel spillage.

4.3REAR ENGINE RIDER DRIVE COMPONENTS 4.3.1. WHEEL BRAKE ADJUSTMENT

CHAIN

CASE

CLUTCH

YOKE

CABLE

HOUSING

SPRING

HOUSING

Test the wheel brake on a dry concrete surface. When properly adjusted, the Rear Engine Rider will stop within 5 feet from fastest speed. If stopping distance is more than 5 feet, the wheel brake should

CABLE END

COTTER

COTTER PIN

be adjusted as follows:

1.Follow WARNING statement found on this page.

2.Check fuel level in tank. If over 3/4 full, remove tank. Refer to Section “REMOVING FUEL TANK”. If 3/4 or less, proceed to next step.

3.Carefully stand Rear Engine Rider on rear bumper.

4.Depress clutch/brake pedal all the way down. Move and hold the park brake lever in the “ON” position and release the clutch/brake pedal to lock the park brake. See Figure 4.8.

DEPRESS

CLUTCH/BRAKE

PIN

1/2” TO 3/4”

FIGURE 4.9

BRAKE CABLE

CHAIN CASE

LOOSEN

JAM NUTS

MOVE PARKING

BRAKE LATCH OVER

TO LOCK

FIGURE 4.8

 

5. Measure the distance between end of

FIGURE 4.10

clutch/brake cable and bottom of housing.

 

Measurement should be no less than 1/2” and no

 

greater than 3/4”. See Figure 4.9.

 

6.If measurement is less than 1/2” or greater than 3/4”, loosen the two jam-nuts. See Figure 4.10. Hold the clutch/brake cable to the chain case bracket.

7.Adjust cable up or down using the jam-nuts to obtain a distance of 1/2” to 3/4” between end of clutch/brake cable (adjustment shown in inset of Figure 4.9) and bottom of housing. See Figure 4.9.

8.After adjustment is complete, securely tighten cable jam-nuts.

23

Image 23
Contents Manual No -3121 I.R /20/99 European Rear Engine Riding Mower SeriesImportant Safety Instructions Operation Table of Contents Nomenclature IntroductionFamiliarization Decals / Symbols Lowest Traction Height CUT Clutch PRE-START Check List OPERATOR’S Seat Adjustment 2.2.1. Front to Rear AdjustmentOn Next Starting & Operation Engine Electric StartEngine Manual Start Starting & OperationEngine Electric Start Wheel Drive Starting & Operation 2.3.3. Mower BladeMower Blade Stopping ENGINE, Wheel DRIVE, Blade 2.4.1. EngineDo not park machine on slopes Cutting Height AdjustmentStopping ENGINE, Wheel DRIVE, Blade 2.4.4. Park Brake Service Engine AIR Cleaner Check Mower Blade Service After First 5 Hours Change Engine OILBlade Brake Service After First 5 Hours 3.2.4. Check Blade Drive BeltService Brake / Park Brake Interlock System Service Every 25 Operating HoursClean Mower Deck Battery Fluid LevelRear Axle Bearing Lubrication Service Every 25 Operating Hours from previousFront Wheel Bearing Lubrication Every TWO Years Service AnnuallyEngine Fuel FilterRemoving Fuel Tank Storage OUT of SeasonMower Drive Belt Adjustment for 25, 28 & 30 M Models Engine Adjustments & RepairMower Deck Adjustment Side-To-Side Levelness Blade Brake AdjustmentFront to Rear Levelness 30 Decks Mower Deck AdjustmentFront to Rear Levelness 25 & 28 Decks Chain Case Clutch Yoke Cable Housing Spring Blade Sharpening Mower Blade Replacement 4.4.1. Blade Wear LimitsBelt Removal Blade Drive Belt ReplacementBelt Replacement Battery Installation Battery Battery RemovalBattery Testing Battery ServiceBattery Storage NEW Battery Preparation 1. Remove battery from cartonSnapper Rear Engine Rider Accessories Stop Problem Probable Cause Corrective ActionImproperly Loss Of TractionBlades Not Cutting Cutting GrassTo be Performed Pages Subject Service ReferenceMAINTENANCE/REPLACEMENT Parts Maintenance Parts Disclaimer of Warranty Year Limited WarrantyService Notes Service Notes European Rear Engine Riding Mower Series

EM250819BE, EM281019BE specifications

The Snapper EM250819BE and EM281019BE are two advanced electric mowers that embody the latest innovations in outdoor power equipment. Aimed at both residential and commercial users, these models offer exceptional performance, efficiency, and user-friendly features to simplify lawn care.

The Snapper EM250819BE features a robust 20-inch cutting deck, providing the ideal balance between maneuverability and coverage. This mower is powered by a high-efficiency brushless motor, which not only extends the lifespan of the instrument but also delivers consistent power output, ensuring an even cut across various grass types. The EM250819BE offers multiple cutting height adjustments, allowing users to customize their lawn's appearance according to seasonal preferences and grass species.

Equipped with a 40V lithium-ion battery, the Snapper EM250819BE boasts an impressive runtime, enabling users to tackle larger yards without interruptions for recharging. The onboard LED battery indicator is particularly handy, allowing users to monitor battery levels easily and plan their mowing schedule without surprises. Additionally, the mower's lightweight design ensures easy maneuverability, making it less strenuous to operate for extended periods.

On the other hand, the Snapper EM281019BE brings a larger 28-inch cutting deck into play, perfect for those who need to cover wider areas quickly. Like its counterpart, this model features a brushless motor that ensures efficient operation and reduces maintenance needs. The EM281019BE also supports various cutting height settings for a tailored mowing experience.

One of the standout features of the EM281019BE is its self-propelled option, allowing users to navigate tougher terrains with minimal effort. This is complemented by enhanced traction control, making it ideal for slopes and uneven lawns. The model also includes a proprietary mulching feature, enabling grass clippings to be finely chopped and returned to the soil, thus promoting healthier lawn growth.

Both models are designed with user comfort and safety in mind. They come with ergonomic handles for better grip and reduced fatigue during extended use. Additionally, the easy-to-access safety features ensure that the mowers meet the highest standards of user protection.

In summary, the Snapper EM250819BE and EM281019BE represent a significant advancement in electric mowing technology, delivering performance, efficiency, and convenience in an environmentally friendly package. With their user-centric design and powerful features, they are excellent choices for anyone looking to achieve a beautiful lawn with less hassle.