Snapper EM250819BE, EM281019BE Mower Deck Adjustment, Front to Rear Levelness 25 & 28 Decks

Page 22

Section 4 - ADJUSTMENTS & REPAIR

WARNING

DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure away from plug. Engine and components are HOT. Avoid serious burns, allow all parts to cool before working on machine. Fuel Filler Cap and Vent must be closed securely to prevent fuel spillage.

4.2.3.MOWER DECK ADJUSTMENT (Side-To-Side Levelness)

(Continued from previous page)

7.Move one side of the deck up or down to achieve levelness between both sides of deck. See Figure 4.6.

8.Tighten carriage bolt and nut securely. Recheck both sides of deck for correct levelness.

9.Readjust rear hanger chain pivots to align with holes in support brackets.

See Figure 4.7.

10.Remove angle iron, pipe, or similar object and proceed to check front to rear levelness.

4.2.3. MOWER DECK ADJUSTMENT

(Front to Rear Levelness - 25” & 28” Decks)

With the Rear Engine Rider on a smooth, level surface, rotate blade until blade tips are at front and rear of deck. Measure the distance from blade tips to floor. The distance should be the same, or the rear 1/8” lower than the front. If the rear blade tip is higher or is more than 1/8” lower than the front, proceed with adjustment.

(Front to Rear Levelness - 30” Decks)

With the Rear Engine Rider on a smooth, level surface, rotate blade until blade tips are at front and rear of deck. Measure the distance from blade tips to floor. The distance should be the same, or the rear 1/8” to 1/4” higher than the front. If the rear blade tip is higher or is more than 1/4” higher than the front, proceed with adjustment.

1.Remove rear hanger chains.

2.Turn each hanger pivot the same number of rotations on the eye-bolt to raise or lower the rear of the deck. See Figure 4.7.

3.Reinstall rear hanger chains and measure blade tips again.

4.Repeat steps “1” through “3” until proper levelness is obtained.

FLOOR

FRONT

REAR

X-1/8”

HANGER

HAIRPINCHAIN PIVOT

SUPPORT

BRACKET

HANGER

CHAIN

FIGURE 4.7

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents European Rear Engine Riding Mower Series Manual No -3121 I.R /20/99Important Safety Instructions Operation Table of Contents Introduction NomenclatureFamiliarization Decals / Symbols Lowest Traction Height CUT Clutch OPERATOR’S Seat Adjustment 2.2.1. Front to Rear Adjustment PRE-START Check ListStarting & Operation Engine Electric Start On NextEngine Electric Start Starting & OperationEngine Manual Start Starting & Operation 2.3.3. Mower Blade Wheel DriveStopping ENGINE, Wheel DRIVE, Blade 2.4.1. Engine Mower BladeStopping ENGINE, Wheel DRIVE, Blade 2.4.4. Park Brake Cutting Height AdjustmentDo not park machine on slopes Service After First 5 Hours Change Engine OIL Service Engine AIR Cleaner Check Mower BladeService Brake / Park Brake Service After First 5 Hours 3.2.4. Check Blade Drive BeltBlade Brake Battery Fluid Level Service Every 25 Operating HoursClean Mower Deck Interlock SystemFront Wheel Bearing Lubrication Service Every 25 Operating Hours from previousRear Axle Bearing Lubrication Fuel Filter Service AnnuallyEngine Every TWO YearsStorage OUT of Season Removing Fuel TankEngine Adjustments & Repair Mower Drive Belt Adjustment for 25, 28 & 30 M ModelsBlade Brake Adjustment Mower Deck Adjustment Side-To-Side LevelnessFront to Rear Levelness 25 & 28 Decks Mower Deck AdjustmentFront to Rear Levelness 30 Decks Chain Case Clutch Yoke Cable Housing Spring Mower Blade Replacement 4.4.1. Blade Wear Limits Blade SharpeningBelt Replacement Blade Drive Belt ReplacementBelt Removal Battery Battery Removal Battery InstallationNEW Battery Preparation 1. Remove battery from carton Battery ServiceBattery Storage Battery TestingSnapper Rear Engine Rider Accessories Problem Probable Cause Corrective Action StopCutting Grass Loss Of TractionBlades Not Cutting ImproperlySubject Service Reference To be Performed PagesMAINTENANCE/REPLACEMENT Parts Maintenance Parts Year Limited Warranty Disclaimer of WarrantyService Notes Service Notes European Rear Engine Riding Mower Series

EM250819BE, EM281019BE specifications

The Snapper EM250819BE and EM281019BE are two advanced electric mowers that embody the latest innovations in outdoor power equipment. Aimed at both residential and commercial users, these models offer exceptional performance, efficiency, and user-friendly features to simplify lawn care.

The Snapper EM250819BE features a robust 20-inch cutting deck, providing the ideal balance between maneuverability and coverage. This mower is powered by a high-efficiency brushless motor, which not only extends the lifespan of the instrument but also delivers consistent power output, ensuring an even cut across various grass types. The EM250819BE offers multiple cutting height adjustments, allowing users to customize their lawn's appearance according to seasonal preferences and grass species.

Equipped with a 40V lithium-ion battery, the Snapper EM250819BE boasts an impressive runtime, enabling users to tackle larger yards without interruptions for recharging. The onboard LED battery indicator is particularly handy, allowing users to monitor battery levels easily and plan their mowing schedule without surprises. Additionally, the mower's lightweight design ensures easy maneuverability, making it less strenuous to operate for extended periods.

On the other hand, the Snapper EM281019BE brings a larger 28-inch cutting deck into play, perfect for those who need to cover wider areas quickly. Like its counterpart, this model features a brushless motor that ensures efficient operation and reduces maintenance needs. The EM281019BE also supports various cutting height settings for a tailored mowing experience.

One of the standout features of the EM281019BE is its self-propelled option, allowing users to navigate tougher terrains with minimal effort. This is complemented by enhanced traction control, making it ideal for slopes and uneven lawns. The model also includes a proprietary mulching feature, enabling grass clippings to be finely chopped and returned to the soil, thus promoting healthier lawn growth.

Both models are designed with user comfort and safety in mind. They come with ergonomic handles for better grip and reduced fatigue during extended use. Additionally, the easy-to-access safety features ensure that the mowers meet the highest standards of user protection.

In summary, the Snapper EM250819BE and EM281019BE represent a significant advancement in electric mowing technology, delivering performance, efficiency, and convenience in an environmentally friendly package. With their user-centric design and powerful features, they are excellent choices for anyone looking to achieve a beautiful lawn with less hassle.
Top Page Image Contents