Snapper EM250819BE, EM281019BE important safety instructions Engine Adjustments & Repair

Page 20

Section 4 - ADJUSTMENTS & REPAIR

WARNING

DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure away from plug. Engine and components are HOT. Avoid serious burns, allow all parts to cool before working on machine. Fuel Filler Cap and Vent must be closed securely to prevent fuel spillage.

4.1ENGINE ADJUSTMENTS & REPAIR

Refer to the engine owner’s manual for those adjustments and/or repairs that can be made by the owner.

4.2MOWER DECK & COMPONENT ADJUSTMENTS The following mower deck and component adjustments and repairs can be made by the owner. However, if there is difficulty in achieving these adjustments and repairs, it is recommended that these repairs be made by an authorized SNAPPER dealer.

4.2.1.MOWER DRIVE BELT ADJUSTMENT (FOR 25”, 28" & 30" "M" MODELS)

1.Remove mower drive belt cover. Refer to Section “CHECK MOWER DRIVE BELT”.

2.Move blade lever up and over to the “ON” position.

3.Place deck cutting height in the 3rd position. Measure the belt spacing at idler pulley. The distance should measure 1-1/4” but no less than 1”. See Figure 4.1.

1-1/4”

FLAT

WASHERS

HAIRPIN

FRAME

SPACERS

FIGURE 4.2

7.Install required number of snap-in frame spacers behind channel pivot until the 1-1/4” distance between belt is maintained. See Figure 4.3.

SNAP-IN FRAME

SPACER

P.N. 2-8395

 

IDLER

ENGINE DRIVE

SPINDLE

PULLEY

PULLEY

ASSEMBLY

PULLEY

 

 

FIGURE 4.1

4.If the distance is less than 1”, adjust belt tension.

5.Remove hairpin and flat washers from pivot stud. See Figure 4.2.

6.Pull front frame forward until distance between belt, with blade lever “ON”, measures 1-1/4”.

FIGURE 4.3

8.Reinstall the required amount of flat washers removed in step “5.” and install hairpin. See Figure

4.2.Retain any remaining spacers for readjustment when a new belt is installed.

IMPORTANT: The SNAPPER "M" Series Rear Engine Rider Models are shipped with additional spacers specifically designed for the Rear Engine Rider. Should additional spacers be required, contact an authorized SNAPPER dealer.

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents European Rear Engine Riding Mower Series Manual No -3121 I.R /20/99Important Safety Instructions Operation Table of Contents Introduction NomenclatureFamiliarization Decals / Symbols Lowest Traction Height CUT Clutch OPERATOR’S Seat Adjustment 2.2.1. Front to Rear Adjustment PRE-START Check ListStarting & Operation Engine Electric Start On NextEngine Manual Start Starting & OperationEngine Electric Start Starting & Operation 2.3.3. Mower Blade Wheel DriveStopping ENGINE, Wheel DRIVE, Blade 2.4.1. Engine Mower BladeDo not park machine on slopes Cutting Height AdjustmentStopping ENGINE, Wheel DRIVE, Blade 2.4.4. Park Brake Service After First 5 Hours Change Engine OIL Service Engine AIR Cleaner Check Mower BladeBlade Brake Service After First 5 Hours 3.2.4. Check Blade Drive BeltService Brake / Park Brake Service Every 25 Operating Hours Clean Mower DeckBattery Fluid Level Interlock SystemRear Axle Bearing Lubrication Service Every 25 Operating Hours from previousFront Wheel Bearing Lubrication Service Annually EngineFuel Filter Every TWO YearsStorage OUT of Season Removing Fuel TankEngine Adjustments & Repair Mower Drive Belt Adjustment for 25, 28 & 30 M ModelsBlade Brake Adjustment Mower Deck Adjustment Side-To-Side LevelnessFront to Rear Levelness 30 Decks Mower Deck AdjustmentFront to Rear Levelness 25 & 28 Decks Chain Case Clutch Yoke Cable Housing Spring Mower Blade Replacement 4.4.1. Blade Wear Limits Blade SharpeningBelt Removal Blade Drive Belt ReplacementBelt Replacement Battery Battery Removal Battery InstallationBattery Service Battery StorageNEW Battery Preparation 1. Remove battery from carton Battery TestingSnapper Rear Engine Rider Accessories Problem Probable Cause Corrective Action StopLoss Of Traction Blades Not CuttingCutting Grass ImproperlySubject Service Reference To be Performed PagesMAINTENANCE/REPLACEMENT Parts Maintenance Parts Year Limited Warranty Disclaimer of WarrantyService Notes Service Notes European Rear Engine Riding Mower Series

EM250819BE, EM281019BE specifications

The Snapper EM250819BE and EM281019BE are two advanced electric mowers that embody the latest innovations in outdoor power equipment. Aimed at both residential and commercial users, these models offer exceptional performance, efficiency, and user-friendly features to simplify lawn care.

The Snapper EM250819BE features a robust 20-inch cutting deck, providing the ideal balance between maneuverability and coverage. This mower is powered by a high-efficiency brushless motor, which not only extends the lifespan of the instrument but also delivers consistent power output, ensuring an even cut across various grass types. The EM250819BE offers multiple cutting height adjustments, allowing users to customize their lawn's appearance according to seasonal preferences and grass species.

Equipped with a 40V lithium-ion battery, the Snapper EM250819BE boasts an impressive runtime, enabling users to tackle larger yards without interruptions for recharging. The onboard LED battery indicator is particularly handy, allowing users to monitor battery levels easily and plan their mowing schedule without surprises. Additionally, the mower's lightweight design ensures easy maneuverability, making it less strenuous to operate for extended periods.

On the other hand, the Snapper EM281019BE brings a larger 28-inch cutting deck into play, perfect for those who need to cover wider areas quickly. Like its counterpart, this model features a brushless motor that ensures efficient operation and reduces maintenance needs. The EM281019BE also supports various cutting height settings for a tailored mowing experience.

One of the standout features of the EM281019BE is its self-propelled option, allowing users to navigate tougher terrains with minimal effort. This is complemented by enhanced traction control, making it ideal for slopes and uneven lawns. The model also includes a proprietary mulching feature, enabling grass clippings to be finely chopped and returned to the soil, thus promoting healthier lawn growth.

Both models are designed with user comfort and safety in mind. They come with ergonomic handles for better grip and reduced fatigue during extended use. Additionally, the easy-to-access safety features ensure that the mowers meet the highest standards of user protection.

In summary, the Snapper EM250819BE and EM281019BE represent a significant advancement in electric mowing technology, delivering performance, efficiency, and convenience in an environmentally friendly package. With their user-centric design and powerful features, they are excellent choices for anyone looking to achieve a beautiful lawn with less hassle.
Top Page Image Contents