Snapper EM250819BE, EM281019BE Blade Drive Belt Replacement, Belt Removal

Page 25

Section 4 - ADJUSTMENTS & REPAIR

WARNING

DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure away from plug. Engine and components are HOT. Avoid serious burns, allow all parts to cool before working on machine. Fuel Filler Cap and Vent must be closed securely to prevent fuel spillage.

4.5BLADE DRIVE BELT REPLACEMENT

Inspect mower drive belt as described in Section “CHECK MOWER DRIVE BELT”. Replace belt if signs of excessive wear and/or damage are present.

4.5.1. BELT REMOVAL

1.Remove mower drive belt cover. Refer to Section “DRIVE BELT COVER REMOVAL”.

2.Remove old belt.

4.5.2. BELT REPLACEMENT

1.Follow WARNING statement found on this page.

2.Check fuel level in tank. If over 3/4 full, remove tank. Refer to Section “REMOVING FUEL TANK”. If 3/4 or less, proceed to next step.

3.Carefully stand Rear Engine Rider on rear bumper.

4.Route new belt through engine belt guide up to engine pulley. See Figure 4.14.

ENGINE PULLEY

ENGINE

BELT

GUIDE

FIGURE 4.14

5.Move transmission shift lever to the neutral (N) position.

6.Rotate clutch yoke (clutch yoke shown in Figure 4.9) out with your hand and work belt between drive disc and rubber driven disc.

7.To clear the primary chain case, move transmission shift lever to the #5 position. Route belt around drive disc and into drive pulley belt groove.

8.Remove idler.

9.Route belt onto spindle pulley. Make sure belt is inside spindle belt guide and idler belt guide. Route belt as shown in Figure 4.15.

10.Reinstall idler removed in Step 8. The idler belt guide tab should be positioned in the hole located on idler arm. Tighten idler pulley bolt securely.

11.Adjust belt guide. See Figure 4.15 for proper belt-to-belt guide clearances.

12.Check mower drive belt tension and adjust if necessary. Refer to Section “MOWER DRIVE BELT ADJUSTMENT”.

13.Reinstall mower drive belt cover.

IDLER BELT GUIDE

1/16” NOMINAL

FIGURE 4.15

25

Image 25
Contents Manual No -3121 I.R /20/99 European Rear Engine Riding Mower SeriesImportant Safety Instructions Operation Table of Contents Nomenclature IntroductionFamiliarization Decals / Symbols Lowest Traction Height CUT Clutch PRE-START Check List OPERATOR’S Seat Adjustment 2.2.1. Front to Rear AdjustmentOn Next Starting & Operation Engine Electric StartEngine Electric Start Starting & OperationEngine Manual Start Wheel Drive Starting & Operation 2.3.3. Mower BladeMower Blade Stopping ENGINE, Wheel DRIVE, Blade 2.4.1. EngineStopping ENGINE, Wheel DRIVE, Blade 2.4.4. Park Brake Cutting Height AdjustmentDo not park machine on slopes Service Engine AIR Cleaner Check Mower Blade Service After First 5 Hours Change Engine OILService Brake / Park Brake Service After First 5 Hours 3.2.4. Check Blade Drive BeltBlade Brake Clean Mower Deck Service Every 25 Operating HoursBattery Fluid Level Interlock SystemFront Wheel Bearing Lubrication Service Every 25 Operating Hours from previousRear Axle Bearing Lubrication Engine Service AnnuallyFuel Filter Every TWO YearsRemoving Fuel Tank Storage OUT of SeasonMower Drive Belt Adjustment for 25, 28 & 30 M Models Engine Adjustments & RepairMower Deck Adjustment Side-To-Side Levelness Blade Brake AdjustmentFront to Rear Levelness 25 & 28 Decks Mower Deck AdjustmentFront to Rear Levelness 30 Decks Chain Case Clutch Yoke Cable Housing Spring Blade Sharpening Mower Blade Replacement 4.4.1. Blade Wear LimitsBelt Replacement Blade Drive Belt ReplacementBelt Removal Battery Installation Battery Battery RemovalBattery Storage Battery ServiceNEW Battery Preparation 1. Remove battery from carton Battery TestingSnapper Rear Engine Rider Accessories Stop Problem Probable Cause Corrective ActionBlades Not Cutting Loss Of TractionCutting Grass ImproperlyTo be Performed Pages Subject Service ReferenceMAINTENANCE/REPLACEMENT Parts Maintenance Parts Disclaimer of Warranty Year Limited WarrantyService Notes Service Notes European Rear Engine Riding Mower Series

EM250819BE, EM281019BE specifications

The Snapper EM250819BE and EM281019BE are two advanced electric mowers that embody the latest innovations in outdoor power equipment. Aimed at both residential and commercial users, these models offer exceptional performance, efficiency, and user-friendly features to simplify lawn care.

The Snapper EM250819BE features a robust 20-inch cutting deck, providing the ideal balance between maneuverability and coverage. This mower is powered by a high-efficiency brushless motor, which not only extends the lifespan of the instrument but also delivers consistent power output, ensuring an even cut across various grass types. The EM250819BE offers multiple cutting height adjustments, allowing users to customize their lawn's appearance according to seasonal preferences and grass species.

Equipped with a 40V lithium-ion battery, the Snapper EM250819BE boasts an impressive runtime, enabling users to tackle larger yards without interruptions for recharging. The onboard LED battery indicator is particularly handy, allowing users to monitor battery levels easily and plan their mowing schedule without surprises. Additionally, the mower's lightweight design ensures easy maneuverability, making it less strenuous to operate for extended periods.

On the other hand, the Snapper EM281019BE brings a larger 28-inch cutting deck into play, perfect for those who need to cover wider areas quickly. Like its counterpart, this model features a brushless motor that ensures efficient operation and reduces maintenance needs. The EM281019BE also supports various cutting height settings for a tailored mowing experience.

One of the standout features of the EM281019BE is its self-propelled option, allowing users to navigate tougher terrains with minimal effort. This is complemented by enhanced traction control, making it ideal for slopes and uneven lawns. The model also includes a proprietary mulching feature, enabling grass clippings to be finely chopped and returned to the soil, thus promoting healthier lawn growth.

Both models are designed with user comfort and safety in mind. They come with ergonomic handles for better grip and reduced fatigue during extended use. Additionally, the easy-to-access safety features ensure that the mowers meet the highest standards of user protection.

In summary, the Snapper EM250819BE and EM281019BE represent a significant advancement in electric mowing technology, delivering performance, efficiency, and convenience in an environmentally friendly package. With their user-centric design and powerful features, they are excellent choices for anyone looking to achieve a beautiful lawn with less hassle.