Snapper CP216017RV, CP215017KWV, CP215017HV, CP215517HV Wheel Drive Control Adjustment, On next

Page 13

Section 4 - REPAIR & ADJUSTMENTS

WARNING

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. Wear heavy leather gloves when handling or working around cutting blades. Blades are extremely sharp and can cause severe injury.

NOTE: The following sections 4.2 through 4.4 are for self-propelled models only.

4.2WHEEL DRIVE CONTROL ADJUSTMENT

1. The wheel drive control is properly adjusted when there is 1/16” to 1/8” clearance between the inside of the spring hook and the inside of the clutch cable eye with the wheel drive control released. See Figure 4.4.

CLUTCH CABLE

VINYL SPRING COVER

 

1/16” TO 1/8”

CLUTCH CABLE

CLEARANCE

EYE

UPPER

 

SPRING

SPRING HOOK

 

LOWER

 

SPRING

 

CABLE

CLUTCH CABLE EYE

SPRING

4. If the wheel drive control fails to return quickly to the “OFF” position when released, check for binding at the cable clips located on the side of the right handle. The upper clip should be located 2” below the upper bolt; the lower clip should be 4” above the lower bolt. The cable should slide freely with the clips installed at these locations.

4.3DRIVEN DISC SERVICE

If the mower does not propel itself properly, See Figure 4.5. Check for the following problems:

DRIVEN DISC &

 

RUBBER RING

POLY-V-BELT

DRIVE

 

SPRING

 

DRIVE

DISC

ENGINE

DRIVE

BELT

FIGURE 4.5

1.Grease on drive disc causing slippage.

2.Broken or disconnected drive spring.

3.Driven disc is out of adjustment.

4.Driven disc rubber ring is worn – does not contact drive disc properly.

5.Worn Poly-V Belt or engine drive belt.

NOTE: If any of the above (1 thru 5) are causing problems, service as follows:

(Continued on next page)

FIGURE 4.4

2.To adjust, unhook upper spring from cable eye and rotate spring in direction required to extend or shorten spring length.

3.Rehook upper spring to cable eye and check clearance. Repeat procedure if required.

NOTE: The vinyl spring cover should be kept over the spring at all times except for adjustments.

13

Image 13
Contents Steel Deck Walk Mowers Commercial Model Series Important Safety Instructions Operation Table of Contents Nomenclature IntroductionStarting & Operation 2.2.1. Engine & Blade PRE-START Check ListTurn fuel valve to on. See .1. Move Handle Height Adjustment Cutting Height AdjustmentStopping Installation of Grass Catcher Recycling Operation Optional AccessoryService After First 5 Hours 3.2.1. Change Engine OIL MaintenanceCheck Mower Blade Check Grease Level in TransmissionCheck Engine Drive Belt Storage Procedure Service AnnuallyEngine Air Filter Engine Oil Blade Sharpening Mower Blade Replacement 4.1.1. Standard Blade Wear LimitDriven Disc Service Wheel Drive Control AdjustmentOn next Driven Disc Adjustment Drive Spring Repair/ReplacementReplacing Driven Disc Rubber Ring Replacing Bearing In Driven Disc Engine Drive Belt Replacement Stretch Type Belts Belt ServicePulley Position Problem Probable Cause Corrective Action TroubleshootingMAINTENANCE/REPLACEMENT Parts Service Performed EachUSE HRS Season Disclaimer of Warranty Year Limited WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Service Notes Service Notes Steel Deck Walk Mowers Commercial Model Series

CP216017RV, CP215017KWV, CP215017HV, CP215517HV, CP215017KWV, CP216017RV, CP214017R2 specifications

The Snapper CP216017RV, CP215017KWV, CP215017HV, CP215517HV, CP215017KWV, CP216017RV, and CP214017R2 are part of Snapper's innovative line of outdoor power equipment, specifically designed for residential lawn care and landscaping needs. These models combine robust engineering with user-friendly features, making them ideal choices for homeowners seeking efficiency and performance in yard maintenance.

One of the standout features across these models is their powerful engine options. For instance, the CP216017RV typically houses a reliable Briggs & Stratton engine that delivers superior performance and torque, enabling it to tackle thick grass and varied terrain with ease. This powerful engine is complemented by a high-capacity fuel tank, offering longer runtimes and reducing the need for frequent refueling during mowing tasks.

In terms of cutting performance, Snapper has designed these models with advanced cutting decks that feature adjustable cutting heights. This enables users to customize their mowing experience, ensuring an even cut suitable for various grass types and conditions. Some models may come equipped with steel cutting decks, enhancing durability and providing a consistent cut over time.

User comfort and convenience are also key aspects of these Snapper models. Ergonomically designed handles provide a comfortable grip and can often be adjusted to accommodate users of different heights. Additionally, many of these models are equipped with features like easy-start technology, eliminating the hassle of traditional pull-start mechanisms and allowing for quick and effortless operation.

With technologies such as the Recycler system, users can benefit from a mulching capability that finely shreds grass clippings, returning nutrients to the lawn while minimizing waste. Moreover, select models offer a bagging option for easy collection of clippings, making cleanup easier and promoting a tidy yard.

The Snapper CP216017RV, CP215017KWV, CP215017HV, CP215517HV, CP215017KWV, CP216017RV, and CP214017R2 models are not only designed for performance but also for reliability and ease of maintenance. Features such as tool-free assembly for cleaning and routine maintenance ensure that users can keep their mowers in optimal condition without unnecessary complications.

Overall, Snapper continues to innovate with these models, meeting the diverse landscaping needs of modern homeowners while ensuring ease of use and exemplary performance in yard care.