Snapper CP215017KWV, CP216017RV, CP214017R2 important safety instructions Blade Sharpening

Page 12

Section 4 - REPAIR & ADJUSTMENTS

WARNING

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. Wear heavy leather gloves when handling or working around cutting blades. Blades are extremely sharp and can cause severe injury.

4.1 MOWER BLADE REPLACEMENT 4.1.1. STANDARD BLADE WEAR LIMIT

1.Inspect blade frequently for signs of excessive wear or damage. See Figure 4.1.

NEW BLADE

WEAR LIMIT (NOTCH STARTS)

DANGEROUS

CONDITION !

DO NOT USE ON

MOWER !

REPLACE WITH NEW

BLADE.

FIGURE 4.1

2.Replace the blade if it is badly chipped, bent, noticeably out of balance or has cracks or notch in either tip. See Figure 4.1. Replace with new blade.

WARNING

DO NOT use a cutting blade that shows signs of excessive wear or damage. Refer to Section “MOWER BLADE REPLACEMENT” for proper blade inspection and service procedures.

4.1.2. BLADE SHARPENING

1.Disconnect spark plug wire and secure end away from plug.

2.Tilt mower up on its rear wheels. Do not tilt mower with spark plug or carburetor down.

3.Remove blade. See Figure 4.2.

MAKE SURE THAT

BLADE HUB IS

SEATED

BLADE BETWEEN

HUBFLANGES

FLANGE

BLADE

CONE WASHER (Concave Side Up)

CAPSCREW

FIGURE 4.2

4.Sharpen blade on a grinding wheel at an angle of 22 to 28 degrees. DO NOT sharpen blade beyond original cutting edge. See Figure 4.3.

DO NOT SHARPEN

BEYOND ORIGINAL

CUTTING EDGE

22-28º

BLADE TIP

END VIEW OF

BLADE ASSEMBLY

ORIGINAL CUTTING EDGE

FIGURE 4.3

5.Check blade for balance. If necessary, correct balance by grinding heavy end of blade.

6.Reinstall blade. See Figure 4.1. Check torque of blade retaining cap screw. Recommended torque should be 40 ft. lbs.

12

Image 12
Contents Steel Deck Walk Mowers Commercial Model Series Important Safety Instructions Operation Table of Contents Introduction NomenclaturePRE-START Check List Starting & Operation 2.2.1. Engine & BladeTurn fuel valve to on. See .1. Move Cutting Height Adjustment Handle Height AdjustmentStopping Recycling Operation Optional Accessory Installation of Grass CatcherMaintenance Service After First 5 Hours 3.2.1. Change Engine OILCheck Grease Level in Transmission Check Mower BladeCheck Engine Drive Belt Service Annually Storage ProcedureEngine Air Filter Engine Oil Mower Blade Replacement 4.1.1. Standard Blade Wear Limit Blade SharpeningWheel Drive Control Adjustment Driven Disc ServiceOn next Drive Spring Repair/Replacement Driven Disc AdjustmentReplacing Driven Disc Rubber Ring Replacing Bearing In Driven Disc Belt Service Engine Drive Belt Replacement Stretch Type BeltsPulley Position Troubleshooting Problem Probable Cause Corrective ActionService Performed Each MAINTENANCE/REPLACEMENT PartsUSE HRS Season Year Limited Warranty Disclaimer of WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Service Notes Service Notes Steel Deck Walk Mowers Commercial Model Series

CP216017RV, CP215017KWV, CP215017HV, CP215517HV, CP215017KWV, CP216017RV, CP214017R2 specifications

The Snapper CP216017RV, CP215017KWV, CP215017HV, CP215517HV, CP215017KWV, CP216017RV, and CP214017R2 are part of Snapper's innovative line of outdoor power equipment, specifically designed for residential lawn care and landscaping needs. These models combine robust engineering with user-friendly features, making them ideal choices for homeowners seeking efficiency and performance in yard maintenance.

One of the standout features across these models is their powerful engine options. For instance, the CP216017RV typically houses a reliable Briggs & Stratton engine that delivers superior performance and torque, enabling it to tackle thick grass and varied terrain with ease. This powerful engine is complemented by a high-capacity fuel tank, offering longer runtimes and reducing the need for frequent refueling during mowing tasks.

In terms of cutting performance, Snapper has designed these models with advanced cutting decks that feature adjustable cutting heights. This enables users to customize their mowing experience, ensuring an even cut suitable for various grass types and conditions. Some models may come equipped with steel cutting decks, enhancing durability and providing a consistent cut over time.

User comfort and convenience are also key aspects of these Snapper models. Ergonomically designed handles provide a comfortable grip and can often be adjusted to accommodate users of different heights. Additionally, many of these models are equipped with features like easy-start technology, eliminating the hassle of traditional pull-start mechanisms and allowing for quick and effortless operation.

With technologies such as the Recycler system, users can benefit from a mulching capability that finely shreds grass clippings, returning nutrients to the lawn while minimizing waste. Moreover, select models offer a bagging option for easy collection of clippings, making cleanup easier and promoting a tidy yard.

The Snapper CP216017RV, CP215017KWV, CP215017HV, CP215517HV, CP215017KWV, CP216017RV, and CP214017R2 models are not only designed for performance but also for reliability and ease of maintenance. Features such as tool-free assembly for cleaning and routine maintenance ensure that users can keep their mowers in optimal condition without unnecessary complications.

Overall, Snapper continues to innovate with these models, meeting the diverse landscaping needs of modern homeowners while ensuring ease of use and exemplary performance in yard care.