Snapper CP215017KWV, CP216017RV, CP214017R2 Recycling Operation Optional Accessory

Page 8

Section 2 - OPERATING INSTRUCTIONS

WARNING

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. Wear heavy leather gloves when handling or working around cutting blades. Blades are extremely sharp and can cause severe injury.

2.6RECYCLING OPERATION - OPTIONAL ACCESSORY

Recycling operation requires optional accessory.

NOTE: For best recycling results, cut up to a maximum of 1/3 of grass blade length and recycle ONLY when grass is dry.

1.Set all wheels in the highest cutting position (Notch 6).

2.Move engine speed control to “FAST” (Rabbit) position.

3.Move ground speed control to slowest speed setting.

4.Proceed mowing slowly. If grass is very dense, lower each rear wheel latch one notch lower than the front wheel latches to improve recycling performance.

2.7INSTALLATION of GRASS CATCHER

Position grass bag between handles. See Figure

2.8.Install grass catcher by sliding connector over flange of adapter. Attach grass bag hooks over middle handle cross bar. See Figure 2.9.

LOWER HANDLES

HANDLE

BAG CONNECTOR

ADAPTER

FLANGE

HOOK BAG

HANDLE OVER

LOWER HANDLES

SLIDE CONNECTOR

OVER END OF

ADAPTER FLANGE

FIGURE 2.9

WARNING

DO NOT operate without entire Grass Catcher or guard in place. Grass Catcher components are subject to deterioration during normal use. Inspect frequently and replace worn or damaged components immediately.

2.8REMOVING and DUMPING GRASS CATCHER

1.Grasp bag connector and bag handle as shown. See Figure 2.8.

2.First, lift up on bag handle, removing it from the mower handle. Then lift up on bag connector removing it from the adapter flange.

3.Dump bag by pulling bag slider off of Z-Fold at rear of bag, opening bag.

4.To close bag, fold rear of bag into Z-shape, keeping edges aligned. Note: an illustration of folding the Z-shape is attached to the bag.

5.Grasp the edge of the Z-fold, and while holding the slider, pull the Z-fold fully into the slider. See Figure 2.10.

GRASP SLIDER.

PULL Z-FOLD INTO

PULL

FIGURE 2.8

FIGURE 2.10

8

Image 8
Contents Steel Deck Walk Mowers Commercial Model Series Important Safety Instructions Operation Table of Contents Introduction NomenclatureTurn fuel valve to on. See .1. Move PRE-START Check ListStarting & Operation 2.2.1. Engine & Blade Stopping Cutting Height AdjustmentHandle Height Adjustment Recycling Operation Optional Accessory Installation of Grass CatcherMaintenance Service After First 5 Hours 3.2.1. Change Engine OILCheck Engine Drive Belt Check Grease Level in TransmissionCheck Mower Blade Engine Air Filter Engine Oil Service AnnuallyStorage Procedure Mower Blade Replacement 4.1.1. Standard Blade Wear Limit Blade SharpeningOn next Wheel Drive Control AdjustmentDriven Disc Service Drive Spring Repair/Replacement Driven Disc AdjustmentReplacing Driven Disc Rubber Ring Replacing Bearing In Driven Disc Belt Service Engine Drive Belt Replacement Stretch Type BeltsPulley Position Troubleshooting Problem Probable Cause Corrective ActionUSE HRS Season Service Performed EachMAINTENANCE/REPLACEMENT Parts Year Limited Warranty Disclaimer of WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Service Notes Service Notes Steel Deck Walk Mowers Commercial Model Series

CP216017RV, CP215017KWV, CP215017HV, CP215517HV, CP215017KWV, CP216017RV, CP214017R2 specifications

The Snapper CP216017RV, CP215017KWV, CP215017HV, CP215517HV, CP215017KWV, CP216017RV, and CP214017R2 are part of Snapper's innovative line of outdoor power equipment, specifically designed for residential lawn care and landscaping needs. These models combine robust engineering with user-friendly features, making them ideal choices for homeowners seeking efficiency and performance in yard maintenance.

One of the standout features across these models is their powerful engine options. For instance, the CP216017RV typically houses a reliable Briggs & Stratton engine that delivers superior performance and torque, enabling it to tackle thick grass and varied terrain with ease. This powerful engine is complemented by a high-capacity fuel tank, offering longer runtimes and reducing the need for frequent refueling during mowing tasks.

In terms of cutting performance, Snapper has designed these models with advanced cutting decks that feature adjustable cutting heights. This enables users to customize their mowing experience, ensuring an even cut suitable for various grass types and conditions. Some models may come equipped with steel cutting decks, enhancing durability and providing a consistent cut over time.

User comfort and convenience are also key aspects of these Snapper models. Ergonomically designed handles provide a comfortable grip and can often be adjusted to accommodate users of different heights. Additionally, many of these models are equipped with features like easy-start technology, eliminating the hassle of traditional pull-start mechanisms and allowing for quick and effortless operation.

With technologies such as the Recycler system, users can benefit from a mulching capability that finely shreds grass clippings, returning nutrients to the lawn while minimizing waste. Moreover, select models offer a bagging option for easy collection of clippings, making cleanup easier and promoting a tidy yard.

The Snapper CP216017RV, CP215017KWV, CP215017HV, CP215517HV, CP215017KWV, CP216017RV, and CP214017R2 models are not only designed for performance but also for reliability and ease of maintenance. Features such as tool-free assembly for cleaning and routine maintenance ensure that users can keep their mowers in optimal condition without unnecessary complications.

Overall, Snapper continues to innovate with these models, meeting the diverse landscaping needs of modern homeowners while ensuring ease of use and exemplary performance in yard care.