Snapper CP216017RV, CP215017KWV, CP215017HV, CP215517HV important safety instructions Operation

Page 3

IMPORTANT SAFETY INSTRUCTIONS

OPERATION

1.DO NOT put hands or feet near or under rotating parts. Keep clear of discharge area while engine is running.

2.STOP engine when crossing gravel drives, walks, or roads, and under any conditions where thrown objects might be a hazard.

3.Mow only in daylight or good artificial light.

4.DO NOT operate mower while under the influence of alcohol or drugs.

5.After striking a foreign object or if mower vibrates abnormally, STOP the engine, disconnect and secure spark plug wire. Inspect the mower for any damage and repair the damage.

6.DO NOT mow near drop offs, ditches or embankments. Operator could lose footing or balance.

7.STAY ALERT for holes and other hidden hazards. Tall grass can hide obstacles. Keep away from ditches, washouts, culverts, fences and protruding objects.

8.DO NOT mow on wet grass. Always be sure of your footing. Keep a firm hold on the handle and walk, never run. Slipping could cause injury.

9.DO NOT leave the machine with the engine running. STOP BLADE and STOP ENGINE before leaving the operators position for any reason.

10.Before cleaning, repairing or inspecting make certain engine, blade and all moving parts have STOPPED. Disconnect and secure spark plug wire away from plug to prevent accidental starting.

11.STOP engine and wait until the blade comes to complete STOP before removing grass bag and/or clearing grass.

12.DO NOT operate mower without the entire grass catcher or guards in place. DO NOT point discharge at people, passing cars, windows or doors.

13.Slow down before turning.

14.Watch out for traffic when near or crossing roadways.

15.DO NOT operate engine in enclosed areas. Engine exhaust gases contain carbon monoxide, a deadly poison.

MAINTENANCE AND STORAGE

1.DO NOT store mower or fuel container inside where fumes may reach an open flame, spark or pilot light such as in a water heater, furnace, clothes dryer or other gas appliance. Allow engine to cool before storing machine in an enclosure. Store fuel container out of reach of children in a well ventilated, unoccupied building.

2.Keep mower and engine free of grass, leaves or excess grease to reduce fire hazard and engine overheating.

3.When draining fuel tank, drain fuel into an approved container outdoors and away from open flame.

4.Keep all bolts, especially blade bolts, nuts and screws properly tight. Check that all cotter pins are in proper position.

5.Always provide adequate ventilation when running engine. Engine exhaust gases contain carbon monoxide, a deadly poison.

6.Service engine and make adjustments only when engine is stopped. Removed spark plug wire from spark plug and secure wire away from spark plug to prevent accidental starting.

7.DO NOT change engine governor speed settings or overspeed engine.

8.Check grass bag assembly frequently for wear or deterioration to avoid thrown objects and exposure to moving parts. Replace with new bag if loose seams or tears are evident. Replace slider or bag adapter if broken or cracked.

9.Mower blades are sharp and can cut. Wrap the blades or wear heavy leather gloves and use CAUTION when handling them.

10.DO NOT test for spark by grounding spark plug next to spark plug hole; spark plug could ignite gas exiting engine.

11.Have machine serviced by an authorized SNAPPER dealer at least once a year and have the dealer install any new safety devices.

12.Use only genuine SNAPPER replacement parts to assure that original standards are maintained.

3

Page 2 Page 4
Image 3
Page 2 Page 4
Contents Steel Deck Walk Mowers Commercial Model Series Important Safety Instructions Operation Table of Contents Nomenclature IntroductionPRE-START Check List Starting & Operation 2.2.1. Engine & BladeTurn fuel valve to on. See .1. Move Cutting Height Adjustment Handle Height AdjustmentStopping Installation of Grass Catcher Recycling Operation Optional AccessoryService After First 5 Hours 3.2.1. Change Engine OIL MaintenanceCheck Grease Level in Transmission Check Mower BladeCheck Engine Drive Belt Service Annually Storage ProcedureEngine Air Filter Engine Oil Blade Sharpening Mower Blade Replacement 4.1.1. Standard Blade Wear LimitWheel Drive Control Adjustment Driven Disc ServiceOn next Driven Disc Adjustment Drive Spring Repair/ReplacementReplacing Driven Disc Rubber Ring Replacing Bearing In Driven Disc Engine Drive Belt Replacement Stretch Type Belts Belt ServicePulley Position Problem Probable Cause Corrective Action TroubleshootingService Performed Each MAINTENANCE/REPLACEMENT PartsUSE HRS Season Disclaimer of Warranty Year Limited WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Service Notes Service Notes Steel Deck Walk Mowers Commercial Model Series

CP216017RV, CP215017KWV, CP215017HV, CP215517HV, CP215017KWV, CP216017RV, CP214017R2 specifications

The Snapper CP216017RV, CP215017KWV, CP215017HV, CP215517HV, CP215017KWV, CP216017RV, and CP214017R2 are part of Snapper's innovative line of outdoor power equipment, specifically designed for residential lawn care and landscaping needs. These models combine robust engineering with user-friendly features, making them ideal choices for homeowners seeking efficiency and performance in yard maintenance.

One of the standout features across these models is their powerful engine options. For instance, the CP216017RV typically houses a reliable Briggs & Stratton engine that delivers superior performance and torque, enabling it to tackle thick grass and varied terrain with ease. This powerful engine is complemented by a high-capacity fuel tank, offering longer runtimes and reducing the need for frequent refueling during mowing tasks.

In terms of cutting performance, Snapper has designed these models with advanced cutting decks that feature adjustable cutting heights. This enables users to customize their mowing experience, ensuring an even cut suitable for various grass types and conditions. Some models may come equipped with steel cutting decks, enhancing durability and providing a consistent cut over time.

User comfort and convenience are also key aspects of these Snapper models. Ergonomically designed handles provide a comfortable grip and can often be adjusted to accommodate users of different heights. Additionally, many of these models are equipped with features like easy-start technology, eliminating the hassle of traditional pull-start mechanisms and allowing for quick and effortless operation.

With technologies such as the Recycler system, users can benefit from a mulching capability that finely shreds grass clippings, returning nutrients to the lawn while minimizing waste. Moreover, select models offer a bagging option for easy collection of clippings, making cleanup easier and promoting a tidy yard.

The Snapper CP216017RV, CP215017KWV, CP215017HV, CP215517HV, CP215017KWV, CP216017RV, and CP214017R2 models are not only designed for performance but also for reliability and ease of maintenance. Features such as tool-free assembly for cleaning and routine maintenance ensure that users can keep their mowers in optimal condition without unnecessary complications.

Overall, Snapper continues to innovate with these models, meeting the diverse landscaping needs of modern homeowners while ensuring ease of use and exemplary performance in yard care.
Top Page Image Contents