Snapper CP215017KWV, CP216017RV, CP214017R2 important safety instructions Pulley Position

Page 18

Section 4 - REPAIR & ADJUSTMENTS

WARNING

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and

4.4.2. Transmission Poly-V Belt Replacement

1.Remove the driven disc. Refer to Section Replacing Driven Disc Rubber Ring” for procedure.

4.Note the routing of the old belt around the three pulleys before removing it. See Figure 4.17.

components are HOT. Avoid serious burns, allow sufficient time for all components to cool.

DRIVE

IDLER

PULLEY DIFFERENTIAL BRACKET

4.4.1.Engine Drive Belt Replacement (Stretch Type Belts)

(Continued From Previous Page)

IMPORTANT: Drain fuel tank before tipping machine. DO NOT tip machine with carburetor or spark plug down. Oil from crankcase will saturate the air filter and cause the engine to be hard to start or not start at all. If contamination does occur, the air filter will have to be replaced.

3.Remove the driven disc. Refer to Section “Replacing Rubber Driven Disc Ring” for driven disc assembly removal procedure.

4.Tilt mower up on its rear wheels and remove blade and blade hub. Assistance from another person may be necessary to hold mower in the tilted position.

5.Hold the slotted end of the drive disc bolt with a screwdriver and remove the nut and internal tooth lock washer. See Figure 4.16.

6.Remove the belt cover located under deck.

7.Lift the drive disc up and remove worn belt.

8.Loop one end of new belt over engine pulley and insert the other end through slot in deck. See Figure 4.15.

PULLEY POSITION

PULLEYPOLY-V

BELT

HEX SHAFT

BELT GUIDE

DRIVEN

 

PULLEY

 

ROUTING OF POLY-V BELT

FIGURE 4.17

5.Place new Poly-V Belt over end of hex shaft and onto driven pulley.

6.Work belt onto top of idler pulley.

7.Twist belt sideways and pull it upward between the differential bracket and drive pulley and then down into the pulley groove. Make sure the Poly-V Belt is above belt guide. See Figure 4.17.

SLOT IN END

OF DRIVE DISC

BOLT

DECK BRACKET (PARTIALLY SHOWN)

DRIVE DISC

BUSHING

BOLT RETAINER

INTERNAL TOOTH LOCKWASHER

NUT

FIGURE 4.16

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Steel Deck Walk Mowers Commercial Model Series Important Safety Instructions Operation Table of Contents Introduction NomenclaturePRE-START Check List Starting & Operation 2.2.1. Engine & BladeTurn fuel valve to on. See .1. Move Cutting Height Adjustment Handle Height AdjustmentStopping Recycling Operation Optional Accessory Installation of Grass CatcherMaintenance Service After First 5 Hours 3.2.1. Change Engine OILCheck Grease Level in Transmission Check Mower BladeCheck Engine Drive Belt Service Annually Storage ProcedureEngine Air Filter Engine Oil Mower Blade Replacement 4.1.1. Standard Blade Wear Limit Blade SharpeningWheel Drive Control Adjustment Driven Disc ServiceOn next Drive Spring Repair/Replacement Driven Disc AdjustmentReplacing Driven Disc Rubber Ring Replacing Bearing In Driven Disc Belt Service Engine Drive Belt Replacement Stretch Type BeltsPulley Position Troubleshooting Problem Probable Cause Corrective ActionService Performed Each MAINTENANCE/REPLACEMENT PartsUSE HRS Season Year Limited Warranty Disclaimer of WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Service Notes Service Notes Steel Deck Walk Mowers Commercial Model Series

CP216017RV, CP215017KWV, CP215017HV, CP215517HV, CP215017KWV, CP216017RV, CP214017R2 specifications

The Snapper CP216017RV, CP215017KWV, CP215017HV, CP215517HV, CP215017KWV, CP216017RV, and CP214017R2 are part of Snapper's innovative line of outdoor power equipment, specifically designed for residential lawn care and landscaping needs. These models combine robust engineering with user-friendly features, making them ideal choices for homeowners seeking efficiency and performance in yard maintenance.

One of the standout features across these models is their powerful engine options. For instance, the CP216017RV typically houses a reliable Briggs & Stratton engine that delivers superior performance and torque, enabling it to tackle thick grass and varied terrain with ease. This powerful engine is complemented by a high-capacity fuel tank, offering longer runtimes and reducing the need for frequent refueling during mowing tasks.

In terms of cutting performance, Snapper has designed these models with advanced cutting decks that feature adjustable cutting heights. This enables users to customize their mowing experience, ensuring an even cut suitable for various grass types and conditions. Some models may come equipped with steel cutting decks, enhancing durability and providing a consistent cut over time.

User comfort and convenience are also key aspects of these Snapper models. Ergonomically designed handles provide a comfortable grip and can often be adjusted to accommodate users of different heights. Additionally, many of these models are equipped with features like easy-start technology, eliminating the hassle of traditional pull-start mechanisms and allowing for quick and effortless operation.

With technologies such as the Recycler system, users can benefit from a mulching capability that finely shreds grass clippings, returning nutrients to the lawn while minimizing waste. Moreover, select models offer a bagging option for easy collection of clippings, making cleanup easier and promoting a tidy yard.

The Snapper CP216017RV, CP215017KWV, CP215017HV, CP215517HV, CP215017KWV, CP216017RV, and CP214017R2 models are not only designed for performance but also for reliability and ease of maintenance. Features such as tool-free assembly for cleaning and routine maintenance ensure that users can keep their mowers in optimal condition without unnecessary complications.

Overall, Snapper continues to innovate with these models, meeting the diverse landscaping needs of modern homeowners while ensuring ease of use and exemplary performance in yard care.
Top Page Image Contents