Snapper 7800391, 7800388, 7800390, 7800378, 7800379 manual Axion / 150Z Series, Initial setup

Page 1

Axion / 150Z Series

Axion / 150Z Series

Initial setup

This Dealer Setup Instruction covers the following products:

	Model. No.	Description
7800360		Simplicity Axion Model ZT18533, 18.5HP w/ 33” Mower
7800380		Simplicity Axion Model CZT18533, 18.5HP w/ 33” Mower (California Model)
7800269		Snapper 150Z	Model SC18533, 18.5HP w/ 33” Mower
7800392		Snapper 150Z	Model CSC18533, 18.5HP w/ 33” Mower (California Model)
7800374		Simplicity Axion Model ZT2142, 21HP w/ 42” Mower
7800381		Simplicity Axion Model CZT2142, 21HP w/ 42” Mower (California Model)
7800386		Snapper 150Z Model SC2142, 21HP w/ 42” Mower
7800393		Snapper 150Z	Model CSC2142, 21HP w/ 42” Mower (California Model)
7800375		Simplicity Axion Model ZT2650, 26HP w/ 50” Mower
7800382		Simplicity Axion Model CZT2650, 26HP w/ 50” Mower (California Model)
7800387		Snapper 150Z Model SC2650, 26HP w/ 50” Mower
7800394		Snapper 150Z	Model CSC2650, 26HP w/ 50” Mower (California Model)

Briggs & Stratton Yard Power Products Group				Form No. 7102754
Copyright © 2008		Briggs & Stratton Corporation

Milwaukee, WI USA. All Rights Reserved

8/2008

1

TP 300-5412---ZT-SN

Image 1

Contents Axion / 150Z Series Initial setupAxion / 150Z Series TABLE OF CONTENTSSETUP PROCEDURES TRANSPORTING AND STORAGE GENERAL OPERATIONSAFETY RULES CHILDREN SLOPE OPERATIONEMISSIONS TOWED EQUIPMENT RIDE-ON UNITSService & Maintenance SERVICE AND MAINTENANCESafe Handling of Gasoline Charge the battery Note proceed with other setup steps Quick Setup Listwhile battery is charging Front tires 18-20 psi, rear tires 10-12 psiIMPORTANT NOTE UncratingDO NOT TOW RIDER Figure 1. Pushing the riderCharge Battery Battery Activation InstallationInstall Battery Figure 2. Charging the battery5/16-18 x 3/4 Installing the SeatFigure 5. Installing the seat 19-25 N.m 14-19 ft. lbsFigure 6. Installing the seat safety switch Installing the Seat Safety SwitchBB D 5/16-18 5/16-18 x 1-3/4 Setting Up the Ground Speed Control LeversFigure 7. Setting up the ground speed levers 20-23 N.m 15-17 ft. lbsNote Use a wooden block to prevent blade rotation Torque Mower Blade HardwareA B 41-54 N.m 30-40 ft. lbs Figure 8. Torquing the mower blade hardware 33” DeckFigure 9. Torquing the mower blade hardware 42” Deck A B 61-75 N.m A B 108-122 N.m 80-90 ft. lbs45-55 ft. lbs Figure 10. Torquing the mower blade hardware 50” Deck Reduce & Check Tire Pressures Check Fluid LevelsFill & Check Engine Oil SizeGrease Lubrication42” Deck shown, all decks similar Figure 13. Lubrication deck Figure 14. Lubrication ground speed control leversOperational SAFETY Checks CHECK RIDER SAFETY SYSTEMBurnish PTO Clutch