Snapper 400 Series manual Troubleshooting Adjustments & Service, Troubleshooting the Rider

Page 25

Troubleshooting

Adjustments & Service

TROUBLESHOOTING WARNING

While normal care and regular maintenance will extend the life of your equipment, prolonged or constant use may eventually require that service be performed to allow it to continue operating properly.

The troubleshooting guide below lists the most common problems, their causes and remedies.

See the information on the following pages for instruc- tions on how to perform most of these minor adjustments and service repairs yourself. If you prefer, all of these procedures can be performed for you by your local authorized dealer.

To avoid serious injury, perform maintenance on the tractor or mower only when the engine is stopped and the parking brake engaged.

Always remove the ignition key, disconnect the spark plug wire and fasten it away from the plug before beginning the maintenance, to prevent accidental starting of the engine.

TROUBLESHOOTING THE RIDER

PROBLEM

CAUSE

REMEDY

Engine will not turnover or start.

1. Ground speed control lever

1.

Shift into neutral.

 

 

not in neutral-start position.

 

 

 

2.

PTO (electric clutch) switch

2.

Place in OFF position.

 

 

in ON position.

 

 

 

3.

Out of fuel.

3.

If engine is hot, allow it to cool, then refill the

 

 

 

 

fuel tank.

 

4.

Engine flooded.

4.

Open the CHOKE.

 

5.

Circuit breaker tripped.

5.

Wait one minute for automatic reset. Replace

 

 

 

 

if defective (see your dealer).

 

6.

Battery terminals require cleaning.

6.

See Normal Care section.

 

7.

Battery discharged or dead.

7.

Recharge or replace.

 

8.

Wiring loose or broken.

8.

Visually check wiring & replace broken or

 

 

 

 

frayed wires. Tighten loose connections.

 

9.

Solenoid or starter motor faulty.

9.

Repair or replace. (see your dealer.)

 

10. Safety interlock switch faulty.

10. Replace if needed (see your dealer.)

 

11. Spark plug(s) faulty, fouled or

11. Clean and gap or replace.

 

 

incorrectly gapped.

 

See engine manual.

 

12. Water in fuel.

12. Drain fuel & refill with fresh fuel.

 

13. Old stale gas.

13. Drain fuel & replace with fresh fuel.

 

14. Brake pedal not depressed.

14. Depress pedal.

 

 

 

 

Engine starts hard or runs poorly.

1. Fuel mixture too rich.

1.

Open the CHOKE.

 

 

 

 

If problem persists, clean the air filter.

 

 

 

 

(See engine manual.)

 

2.

Carburetor adjusted incorrectly.

2.

See engine manual.

 

3.

Spark plug(s) faulty, fouled, or

3.

Clean & gap or replace. See engine manual.

 

 

incorrectly gapped.

 

 

 

 

 

 

Engine knocks.

1. Low oil level.

1.

Check/add oil as required.

 

2.

Using wrong grade oil.

2.

See engine manual.

 

 

 

 

Excessive oil consumption.

1. Engine running too hot.

1.

Clean engine fins, blower screen and air

 

 

 

 

cleaner.

 

2.

Using wrong weight oil.

2.

See engine manual.

 

3.

Too much oil in crankcase.

3.

Drain excess oil.

 

 

 

 

Engine exhaust is black.

1. Dirty air filter.

1.

Clean air filter. See engine manual.

 

2.

Choke not fully open.

2.

Open CHOKE.

 

 

 

 

If problem persists, check air filter and

 

 

 

 

carburetor adjustments. See engine manual.

23

Page 24 Page 26
Image 25
Page 24 Page 26
Contents 16HP Hydro Riders 13HP Hydro Riders Mower DecksPage Table of Contents Safety Rules & Information Operating Safety Slope Operation Safety Rules and InformationGeneral Operation Safety Rules & InformationIgnition System Service and Maintenance CE Identification TAG Markings Identification NumbersNorth American CE ModelsSafety Decals Safety DecalsNorth American Models CE ModelsSafety Icons CE Safety IconsThrottle/Choke Control Control FunctionsThrottle Control ChokeFeatures & Controls Operational Safety Checks General Operating SafetyAdding Fuel Checks Before StartingStarting the Engine Operating the RiderStopping the Rider Selecting Ground & Engine SpeedOperating the Mower Attachment Operation in Reverse Mowing in ReversePushing the Rider by Hand Mower Removal and Installation Storage Check Tire Pressures Regular MaintenanceFuel Filter Raising the Seat DeckLubrication Regular MaintenanceCleaning the Battery and Cables Battery MaintenanceLubricate Rear Axle Shafts Removing The Blade Servicing the Mower BladesTroubleshooting the Rider Troubleshooting Adjustments & ServiceTroubleshooting the Mower Troubleshooting, Adjustment & ServiceTroubleshooting the Rider Steering Gear Adjustment Seat AdjustmentSteering Wheel Adjustment Brake Adjustment AdjustmentsBrake Adjustment Blade Brake CheckSide-To-Side Leveling Mower AdjustmentsFront-To-Back Leveling Transport Height Adjustment Battery ChargingRider Drive Belt Belt ReplacementMower Belt Engine DimensionsTransmission ChassisMaintenance Items Replacement PartsOptional Accessories Technical ManualsPage Lawn Care Lawn Care & Mowing Information Page

400 Series specifications

The Snapper 400 Series is a robust line of riding lawn mowers designed for homeowners looking for efficiency and power in lawn maintenance. This series is known for its reliable performance, user-friendly features, and innovative technology, making it a popular choice among homeowners and landscaping professionals alike.

One of the standout features of the Snapper 400 Series is its powerful engine options. Equipped with a range of high-performance Briggs & Stratton engines, these mowers offer impressive torque and cutting capabilities. The series is designed to handle diverse lawn conditions, from flat terrains to steep inclines, providing a consistent cutting experience.

Ergonomics play a crucial role in the design of the Snapper 400 Series. The mowers come with an adjustable seat, allowing users to find their ideal position for comfort during longer mowing sessions. The intuitive dashboard features all necessary controls within easy reach, enabling users to operate the mower with minimal effort.

The cutting decks in the Snapper 400 Series are engineered for versatility. With options for both side discharge and mulching, users can choose the best approach for their lawn. The mowing heights are adjustable, allowing for a custom cut that suits individual preferences and grass types. Additionally, the steel cutting decks provide durability, ensuring that the mowers withstand frequent use without significant wear.

Another notable innovation within the Snapper 400 Series is the ReadyStart technology. This system ensures that the engine starts easily with just one pull, eliminating the frustration that comes with traditional pull-start engines. The use of a hydrostatic transmission offers smooth and precise control over speed and direction, further enhancing the mowing experience.

The Snapper 400 Series is also aesthetically designed, with a modern appearance that appeals to a wide range of consumers. Its compact size allows it to navigate through tighter spaces, making it practical for varied landscape designs.

Overall, the Snapper 400 Series combines power, comfort, and innovative features to deliver exceptional lawn care solutions. Whether you are an experienced landscaper or a first-time mower owner, the Snapper 400 Series provides the tools necessary for effective and enjoyable lawn maintenance. Its reputation for durability and performance makes it a top contender in the riding mower market.
Top Page Image Contents