Snapper 400 Series manual Safety Rules & Information, General Operation

Page 6

Safety Rules & Information

Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment.

This mowing deck is capable of amputating hands and feet and throwing objects.

The triangle in text signifies important cautions or warnings which must be followed.

GENERAL OPERATION

1.Read, understand, and follow all instructions in the manual and on the unit before starting.

2.Do not put hands or feet near rotating parts or under the machine. Keep clear of the discharge opening at all times.

3.Only allow responsible adults, who are familiar with the instructions, to operate the unit (local regulations can restrict operator age).

4.Clear the area of objects such as rocks, toys, wire, etc., which could be picked up and thrown by the blade(s).

5.Be sure the area is clear of other people before mow- ing. Stop the unit if anyone enters the area.

6.Never carry passengers.

7.Do not mow in reverse unless absolutely necessary. Always look down and behind before and while travel- ling in reverse.

8.Never direct discharge material toward anyone. Avoid discharging material against a wall or obstruc- tion. Material may ricochet back toward the operator. Stop the blade(s) when crossing gravel surfaces.

9.Do not operate the machine without the entire grass catcher, discharge guard (deflector), or other safety devices in place.

10.Slow down before turning.

11.Never leave a running unit unattended. Always disen- gage the PTO, set parking brake, stop engine, and remove keys before dismounting.

12.Disengage blades (PTO) when not mowing. Shut off engine and wait for all parts to come to a complete stop before cleaning the machine, removing the grass catcher, or unclogging the discharge guard.

13.Operate the machine only in daylight or good artificial light.

14.Do not operate the unit while under the influence of alcohol or drugs.

15Watch for traffic when operating near or crossing roadways.

16.Use extra care when loading or unloading the unit into a trailer or truck.

17.Always wear eye protection when operating this unit.

18.Data indicates that operators, age 60 years and above, are involved in a large percentage of power equipment-related injuries. These operators should evaluate their ability to operate the equipment safely enough to protect themselves and others from injury.

19.Follow the manufacturer’s recommendations for wheel weights or counterweights.

20.Keep in mind the operator is responsible for accidents occurring to other people or property.

21.All drivers should seek and obtain professional and practical instruction.

22.Always wear substantial footwear and trousers. Never operate when barefoot or wearing sandals.

23.Before using, always visually check that the blades and blade hardware are present, intact, and secure. Replace worn or damaged parts.

24.Disengage attachments before: refueling, removing an attachment, making adjustments (unless the adjustment can be made from the operator’s posi- tion).

25.When the machine is parked, stored, or left unattend- ed, lower the cutting means unless a positive mechanical lock is used.

26.Before leaving the operator’s position for any reason, engage the parking brake (if equipped), disengage the PTO, stop the engine, and remove the key.

27.To reduce fire hazard, keep the unit free of grass, leaves, & excess oil. Do not stop or park over dry leaves, grass, or combustible materials.

28.It is a violation of California Public Resource Code Section 4442 to use or operate the engine on or near any forest-covered, brush-covered, or grass-covered land unless the exhaust system is equipped with a spark arrester meeting any applicable local or state laws. Other states or federal areas may have similar laws.

TRANSPORTING AND STORAGE

1.When transporting the unit on an open trailer, make sure it is facing forward, in the direction of travel. If the unit is facing backwards, wind lift could damage the unit.

2.Always observe safe refueling and fuel handling prac- tices when refueling the unit after transportation or storage.

3.Never store the unit (with fuel) in an enclosed poorly ventilated structure. Fuel vapors can travel to an ignition source (such as a furnace, water heater, etc.) and cause an explosion. Fuel vapor is also toxic to humans and animals.

4.Always follow the engine manual instructions for storage preparations before storing the unit for both short and long term periods.

5.Always follow the engine manual instructions for proper start-up procedures when returning the unit to service.

6.Never store the unit or fuel container inside where there is an open flame or pilot light, such as in a water heater. Allow unit to cool before storing.

4

Image 6
Contents 13HP Hydro Riders Mower Decks 16HP Hydro RidersPage Table of Contents Safety Rules & Information Operating Safety Safety Rules and Information Slope OperationSafety Rules & Information General OperationIgnition System Service and Maintenance North American Identification NumbersCE Identification TAG Markings CE ModelsNorth American Models Safety DecalsSafety Decals CE ModelsCE Safety Icons Safety IconsThrottle Control Control FunctionsThrottle/Choke Control ChokeFeatures & Controls Adding Fuel General Operating SafetyOperational Safety Checks Checks Before StartingOperating the Rider Starting the EngineSelecting Ground & Engine Speed Stopping the RiderOperating the Mower Mowing in Reverse Attachment Operation in ReversePushing the Rider by Hand Mower Removal and Installation Storage Regular Maintenance Check Tire PressuresRaising the Seat Deck Fuel FilterRegular Maintenance LubricationBattery Maintenance Cleaning the Battery and CablesLubricate Rear Axle Shafts Servicing the Mower Blades Removing The BladeTroubleshooting Adjustments & Service Troubleshooting the RiderTroubleshooting, Adjustment & Service Troubleshooting the MowerTroubleshooting the Rider Seat Adjustment Steering Gear AdjustmentSteering Wheel Adjustment Brake Adjustment AdjustmentsBrake Adjustment Blade Brake CheckMower Adjustments Side-To-Side LevelingFront-To-Back Leveling Battery Charging Transport Height AdjustmentBelt Replacement Rider Drive BeltMower Belt Transmission DimensionsEngine ChassisOptional Accessories Replacement PartsMaintenance Items Technical ManualsPage Lawn Care Lawn Care & Mowing Information Page

400 Series specifications

The Snapper 400 Series is a robust line of riding lawn mowers designed for homeowners looking for efficiency and power in lawn maintenance. This series is known for its reliable performance, user-friendly features, and innovative technology, making it a popular choice among homeowners and landscaping professionals alike.

One of the standout features of the Snapper 400 Series is its powerful engine options. Equipped with a range of high-performance Briggs & Stratton engines, these mowers offer impressive torque and cutting capabilities. The series is designed to handle diverse lawn conditions, from flat terrains to steep inclines, providing a consistent cutting experience.

Ergonomics play a crucial role in the design of the Snapper 400 Series. The mowers come with an adjustable seat, allowing users to find their ideal position for comfort during longer mowing sessions. The intuitive dashboard features all necessary controls within easy reach, enabling users to operate the mower with minimal effort.

The cutting decks in the Snapper 400 Series are engineered for versatility. With options for both side discharge and mulching, users can choose the best approach for their lawn. The mowing heights are adjustable, allowing for a custom cut that suits individual preferences and grass types. Additionally, the steel cutting decks provide durability, ensuring that the mowers withstand frequent use without significant wear.

Another notable innovation within the Snapper 400 Series is the ReadyStart technology. This system ensures that the engine starts easily with just one pull, eliminating the frustration that comes with traditional pull-start engines. The use of a hydrostatic transmission offers smooth and precise control over speed and direction, further enhancing the mowing experience.

The Snapper 400 Series is also aesthetically designed, with a modern appearance that appeals to a wide range of consumers. Its compact size allows it to navigate through tighter spaces, making it practical for varied landscape designs.

Overall, the Snapper 400 Series combines power, comfort, and innovative features to deliver exceptional lawn care solutions. Whether you are an experienced landscaper or a first-time mower owner, the Snapper 400 Series provides the tools necessary for effective and enjoyable lawn maintenance. Its reputation for durability and performance makes it a top contender in the riding mower market.