Snapper 1700, 2700, 400 manual Mower Deck Removal & Installation, Removing the Mower Deck

Page 20

Operating the Tractor

Mower Deck Removal & Installation

44” Simplicity, Massey Ferguson or AGCO Models

WARNING

Engage parking brake, disengage PTO, stop engine and remove key before attempting to install or remove the mower.

B

A

C

D

Figure 6. Lift Arms

(Viewed from underneath right side of tractor)

A.

Mower Lift Arm

C. Flat Washer

B.

Tractor Lift Arm

D. Safety Clip

Removing the Mower Deck

Note: Units with electric height of cut, unplug tractor wire harness from deck harness before removing deck.

1.Park tractor on a hard, level surface such as a con- crete floor. Turn off PTO switch and engine, remove the key and apply parking brake.

2.Place mower in the lowest cutting position using the mower height adjuster.

3.Place the attachment lift in the lowest position.

4.Disconnect the mower lift arm (A, Figure 6) from the tractor lift arm (B). Re-install washer (C) and safety clip (D).

CAUTION

B

A

Figure 7. Removing & Installing Belt

A.Idler Arm

B.PTO Pulley

The muffler and surrounding areas may be hot.

5.Remove belt from PTO pulley (B, Figure 7).

6.Turn wheels straight ahead. Pull back on spring- loaded lever (B, Figure 8) and lift mower hitch off of the tractor brackets.

7.Turn wheels fully left, and slide mower deck out right side of tractor.

Installing the Mower Deck

1.Park tractor, shut off PTO and engine, remove the key and apply parking brake. Turn the wheels fully to the left.

2.Place mower height adjuster (B, Figures 5) in the lowest cutting position. Place the mower lift lever in the lowest position, also. Slide mower deck under right side of tractor so that mower hitch is aligned with the front tractor hitch.

3.See Figure 8. Turn wheels straight. Pull back on the spring-loaded lever (B) while lifting up on the mower hitch. Install mower hitch onto tractor hitch brackets

(A). When properly installed, the spring-loaded lever should seat fully underneath the brackets.

A

B

Figure 8. Mower Hitch

A.Tractor Hitch Brackets

B.Spring-Loaded Lever

4.See Figure 6. Connect the mower lift arm (A) to the tractor lift arm (B) using the flat washer (C) and safety clip (D).

5.See Figure 7. Move idler arm (A) to relieve belt ten- sion. Install belt onto the PTO pulley (B).

Note: Units with electric height of cut, connect tractor

18 wire harness to deck harness.

Page 19 Page 21
Image 20
Page 19 Page 21
Contents 23HP Hydro Tractors Mower Decks 25HP Hydro Tractors27HP Hydro Tractors 1735106Page Table of Contents Safety Rules & Information Operating Safety Safety Rules and Information Slope OperationSafety Rules & Information General OperationIgnition System Service & Maintenance Safe Handling of GasolineIdentification Numbers North AmericanCE Models OnlySafety Decals Safety DecalsDecal Operating Instructions, Models Decal Cutting Height Decal Cutting HeightCE Safety Icons Safety IconsControl Functions Throttle ControlChoke HeadlightsFeatures & Controls What is Automatic Controlled Traction? Parking Brake FunctionAutomatic Controlled Traction w/o 4WD Attachment Lift Control LeverVolt Power Outlet Dashboard Display & FunctionsDisplay Items FunctionsAdding Fuel General Operating SafetyOperational Safety Checks Operating the Tractor Starting the EngineStopping the Tractor & Engine Driving The TractorAttachment Operation in Reverse MowingMowing in Reverse Adjusting Mower Cutting Height Pushing the Tractor by HandMower Deck Removal & Installation Installing the Mower DeckSimplicity, Massey Ferguson or Agco Models Removing the Mower DeckSnapper Models Upper Hanger Upper Hole Lift Hook Lower Hole Long HubSimplicity, Massey Ferguson and Agco Models Pivoting Gauge Wheels Select ModelsMower Hitch Tractor Hitch Brackets Spring-Loaded Lever Snapper Models Attaching a Trailer StorageManual Lift Models Lift Variations When Using AttachmentsHydraulic Lift Models How and When to Water Fertilize & AerateHow High To Mow the Grass Tall Grass Requires Incremental CuttingProper Mowing Speed When and How Often to MowLawn Care & Mowing Information Regular Maintenance Before Every Spring Each Hours 100 250 Fall UseRegular Maintenance Battery Maintenance Cleaning the Battery and CablesCheck Tire Pressures SizeOil LubricationGrease Mower Lubrication Points Arbor Lubrication PointServicing the Mower Blabes Blade RemovalTransmission Maintenance K66 MaintenanceK664 Maintenance Transmission IdentificationK71 Maintenance Service Interval Every 5 HoursService Interval After 50 Hrs, Then Every 250 Hrs Transmission Oil Capacity Apx -1/2 qt 4.25 LInternal Transmission Filter Service Filter Access Cap Troubleshooting Adjustment, & Service TroubleshootingTroubleshooting, Adjustment, & Service Tractor TroubleshootingManual Lift Assist Adjustment Battery ChargingSeat Adjustment Steering Wheel Adjustment Steering Gear AdjustmentBrake Adjustment Thicker Spoke Faces SeatPTO Clutch Adjustment Mower AdjustmentsTransport Height & Ground Following Adjustment Select Models Gauge Wheels Select ModelsLeveling The Mower Leveling The Mower Side-to-Side, J-Hook Models LocknutMower Belt Replacement 44 & 50 PTO Belt ReplacementTo avoid damaging belts, do not PRY GapArbor Drive Belt Replacement 23 HP* Briggs & Stratton 25 HP* Kohler27 HP* Kohler K71Replacement Parts Maintenance ItemsOptional Accessories Technical Manuals

1700, 2700, 400 specifications

The Snapper series of mowers, including the Snapper 1700, 2700, and 400 models, represents a blend of power, efficiency, and innovative technology designed for lawn care enthusiasts and professionals alike. Each model offers unique features tailored to meet diverse mowing needs, ensuring top performance and ease of use.

The Snapper 1700 is ideal for residential yards and smaller properties. It is equipped with a reliable engine that delivers smooth, consistent power to tackle various grass types. The mower features a compact design, making it easy to maneuver around obstacles such as flower beds and trees. One of its standout attributes is the innovative easy-to-use height adjustment mechanism, allowing users to effortlessly change cutting heights to best suit their lawn conditions. Additionally, the Snapper 1700 boasts a robust cutting deck that ensures an even cut, resulting in a professional-grade finish.

The Snapper 2700 is a step up from the 1700, designed for users who require more power and capacity. This model comes with a larger cutting width, allowing for quicker mowing of expansive lawns. Enhanced features include an advanced mower deck technology that optimizes grass clipping discharge, helps to reduce clumping, and improves overall efficiency. The Snapper 2700 also incorporates ergonomic controls, providing comfort during prolonged use, and its durable construction ensures longevity. Furthermore, its rear-wheel drive system enhances traction, particularly on uneven terrain.

For those managing larger properties or commercial landscapes, the Snapper 400 offers premium performance and advanced technology. This model features a high-powered engine for maximum cutting performance, even in challenging conditions. The Snapper 400 is equipped with an intuitive digital display, providing essential information such as battery life and maintenance reminders, ensuring optimal performance over time. The mower's heavy-duty frame and reinforced deck enhance durability, making it suitable for rigorous tasks. It also boasts an innovative mulching capability, enabling users to finely chop grass clippings and return them to the soil as nutrient-rich mulch.

In summary, the Snapper 1700, 2700, and 400 models cater to a wide range of lawn care needs, from small yards to expansive landscapes. Each model combines innovative features, advanced technology, and durable construction, making them reliable choices for homeowners and professionals seeking superior mowing solutions.
Top Page Image Contents