Snapper 1700, 2700, 400 manual K71 Maintenance, Transmission Oil Capacity Apx -1/2 qt 4.25 L

Page 36

Regular Maintenance

A

Figure 32. Seat Deck Access Plug

A. Expansion Chamber Access Plug

K71 Maintenance

The following maintenance procedures must be per- formed on the K71 transmission after the first 50 hours of operation and then after every 250 hours.

TRANSMISSION INFORMATION

Transmission Oil Capacity: Apx. 4-1/2 qt (4.25 L)

Transmission Oil Type: SAE 10W-30 with a minimum API rating of SG/CD.

Internal Oil Filter Part Number: 1719832

Hydraulic System Oil Filter Part Number: 1719168

CHECK TRANSMISSION OIL LEVEL

Service Interval: Every 5 Hours

NOTE: Lift cylinder should be extended.

1.Slide the seat assembly back to access the plastic plug in the top of the seat deck (see Figure 32). Remove the plug.

2.Clean the area around the expansion chamber. Open the lid and check that there is oil present in the bottom of the expansion chamber. If there is no oil present, add 10W-30 SG engine oil until the oil level is 7/16” (1 cm) above the bottom. DO NOT OVER- FILL. Empty space is required in the expansion chamber for heat expansion.

CHANGE TRANSMISSION OIL, INTERNAL FILTER, & HYDRAULIC SYSTEM FILTER

Service Interval: After 50 Hrs, Then Every 250 Hrs

NOTE: The oil should also be changed whenever it has become discolored from overheating or contamination.

NOTE: Support the frame with jackstands and remove the left rear wheel for easier access to the differential fill plug (Figure 33).

1.Place a drain pan under the transmission and remove the two 14mm drain plugs (A, Figure 34).

2.Remove the differential fill cap (B, Figure 35).

3.Remove the filter access cap (B, Figure 34).

4.Remove and replace the hydraulic system filter (A, Figure 35). Thread the new filter onto the filter base and tighten 1/2 to 3/4 turns past finger tight.

A

Figure 33. Differential Fill Plug Access

A. Differential Fill Plug

AB

Figure 34. Transmission Drain Plugs

A.14mm Drain Plugs

B.Filter Access Cap

A

B

Figure 35. Hydraulic System Oil Filter

A.Hydraulic System Filter

B.Differential Fill Cap

34

Page 35 Page 37
Image 36
Page 35 Page 37
Contents 23HP Hydro Tractors Mower Decks 25HP Hydro Tractors27HP Hydro Tractors 1735106Page Table of Contents Safety Rules & Information Operating Safety Safety Rules and Information Slope OperationSafety Rules & Information General OperationIgnition System Service & Maintenance Safe Handling of GasolineIdentification Numbers North AmericanCE Models OnlySafety Decals Safety DecalsDecal Operating Instructions, Models Decal Cutting Height Decal Cutting HeightCE Safety Icons Safety IconsControl Functions Throttle ControlChoke HeadlightsFeatures & Controls What is Automatic Controlled Traction? Parking Brake FunctionAutomatic Controlled Traction w/o 4WD Attachment Lift Control LeverVolt Power Outlet Dashboard Display & FunctionsDisplay Items FunctionsGeneral Operating Safety Operational Safety ChecksAdding Fuel Operating the Tractor Starting the EngineStopping the Tractor & Engine Driving The TractorMowing Mowing in ReverseAttachment Operation in Reverse Adjusting Mower Cutting Height Pushing the Tractor by HandMower Deck Removal & Installation Installing the Mower DeckSimplicity, Massey Ferguson or Agco Models Removing the Mower DeckSnapper Models Upper Hanger Upper Hole Lift Hook Lower Hole Long HubSimplicity, Massey Ferguson and Agco Models Pivoting Gauge Wheels Select ModelsMower Hitch Tractor Hitch Brackets Spring-Loaded Lever Snapper Models Attaching a Trailer StorageLift Variations When Using Attachments Hydraulic Lift ModelsManual Lift Models How and When to Water Fertilize & AerateHow High To Mow the Grass Tall Grass Requires Incremental CuttingWhen and How Often to Mow Lawn Care & Mowing InformationProper Mowing Speed Regular Maintenance Before Every Spring Each Hours 100 250 Fall UseRegular Maintenance Battery Maintenance Cleaning the Battery and CablesCheck Tire Pressures SizeLubrication GreaseOil Mower Lubrication Points Arbor Lubrication PointServicing the Mower Blabes Blade RemovalTransmission Maintenance K66 MaintenanceK664 Maintenance Transmission IdentificationK71 Maintenance Service Interval Every 5 HoursService Interval After 50 Hrs, Then Every 250 Hrs Transmission Oil Capacity Apx -1/2 qt 4.25 LInternal Transmission Filter Service Filter Access Cap Troubleshooting Adjustment, & Service TroubleshootingTroubleshooting, Adjustment, & Service Tractor TroubleshootingBattery Charging Seat AdjustmentManual Lift Assist Adjustment Steering Wheel Adjustment Steering Gear AdjustmentBrake Adjustment Thicker Spoke Faces SeatPTO Clutch Adjustment Mower AdjustmentsTransport Height & Ground Following Adjustment Select Models Gauge Wheels Select ModelsLeveling The Mower Leveling The Mower Side-to-Side, J-Hook Models LocknutMower Belt Replacement 44 & 50 PTO Belt ReplacementTo avoid damaging belts, do not PRY GapArbor Drive Belt Replacement 23 HP* Briggs & Stratton 25 HP* Kohler27 HP* Kohler K71Replacement Parts Maintenance ItemsOptional Accessories Technical Manuals

1700, 2700, 400 specifications

The Snapper series of mowers, including the Snapper 1700, 2700, and 400 models, represents a blend of power, efficiency, and innovative technology designed for lawn care enthusiasts and professionals alike. Each model offers unique features tailored to meet diverse mowing needs, ensuring top performance and ease of use.

The Snapper 1700 is ideal for residential yards and smaller properties. It is equipped with a reliable engine that delivers smooth, consistent power to tackle various grass types. The mower features a compact design, making it easy to maneuver around obstacles such as flower beds and trees. One of its standout attributes is the innovative easy-to-use height adjustment mechanism, allowing users to effortlessly change cutting heights to best suit their lawn conditions. Additionally, the Snapper 1700 boasts a robust cutting deck that ensures an even cut, resulting in a professional-grade finish.

The Snapper 2700 is a step up from the 1700, designed for users who require more power and capacity. This model comes with a larger cutting width, allowing for quicker mowing of expansive lawns. Enhanced features include an advanced mower deck technology that optimizes grass clipping discharge, helps to reduce clumping, and improves overall efficiency. The Snapper 2700 also incorporates ergonomic controls, providing comfort during prolonged use, and its durable construction ensures longevity. Furthermore, its rear-wheel drive system enhances traction, particularly on uneven terrain.

For those managing larger properties or commercial landscapes, the Snapper 400 offers premium performance and advanced technology. This model features a high-powered engine for maximum cutting performance, even in challenging conditions. The Snapper 400 is equipped with an intuitive digital display, providing essential information such as battery life and maintenance reminders, ensuring optimal performance over time. The mower's heavy-duty frame and reinforced deck enhance durability, making it suitable for rigorous tasks. It also boasts an innovative mulching capability, enabling users to finely chop grass clippings and return them to the soil as nutrient-rich mulch.

In summary, the Snapper 1700, 2700, and 400 models cater to a wide range of lawn care needs, from small yards to expansive landscapes. Each model combines innovative features, advanced technology, and durable construction, making them reliable choices for homeowners and professionals seeking superior mowing solutions.
Top Page Image Contents