Snapper 1700, 2700, 400 manual Snapper Models

Page 24

Operating the Tractor

Mower Deck Removal & Installation

50” Snapper Models

E

A

B

C

D

WARNING

Engage parking brake, disengage PTO, stop engine and remove key before attempting to install or remove the mower.

Muffler and surrounding areas may be hot.

Removing the Mower Deck

1.Park the tractor, fully lower the attachment lift, turn off the PTO, turn off the engine, remove the key, and engage the parking brake. If equipped, pivot the gauge wheels into sliding position (see Figure 11).

2.Place mower in the lowest cutting position using the mower height control.

3.Place the attachment lift in the highest position.

4.From left side of tractor, use the idler arm (F, Figure 14) to relieve belt tension. Remove the belt (E) from the PTO pulley.

5.Disconnect outside chain (D, Figure 14) from hanger

(C). Repeat on other side.

CAUTION

The muffler and surrounding areas may be hot.

6.Place the attachment lift in the lowest position.

7.Disconnect lift chain (B) from lift hook (A). Repeat on other side.

8.Turn the wheels straight ahead. Pull back on spring- loaded lever (B, Figure 15) and lift mower hitch off of the tractor brackets (A).

9.Turn wheels fully left, and slide mower deck out from under the right side of the tractor.

Installing the Mower Deck

NOTE: Perform mower installation on a hard, level sur- face such as a concrete floor.

1.Park the tractor, fully lower the attachment lift, turn off the PTO switch, turn off the engine, remove the key, and engage the parking brake. Turn the wheels fully to the left.

F

Figure 14. Mower Lift

 

A. Lift Hook

D. Outside Chain

B. Lift Chain, Inside

E. PTO Belt

C. Hanger

F. Idler Arm

A

B

Figure 15. Mower Hitch

A.Tractor Hitch Brackets

B.Spring-Loaded Lever

2.Place mower in the lowest cutting position using the mower height adjuster. Slide the mower deck under the right side of tractor so that the mower hitch is aligned with front tractor hitch (A, Figure 15).

3.See Figure 15. Turn wheels straight. Pull back on the spring-loaded lever (B) while lifting up on the mower hitch. Install the mower hitch onto tractor hitch brackets (A). When properly installed, the spring- loaded lever should seat fully underneath the brack- ets (A).

4.Connect the lift chains (B, Figure 14) to the the trac- tor lift hooks (A).

5.Place the attachment lift in the highest position.

6.Connect outside chains (D, Figure 14) to hanger (C).

7.From left side of tractor, use the idler arm (F, Figure 14) to relieve belt tension. Install belt (E) onto the PTO pulley.

8.If equipped, raise the attachment lift and rotate the front gauge wheels (Figure 11) into cutting position.

22

Image 24
Contents 23HP Hydro Tractors Mower Decks 25HP Hydro Tractors27HP Hydro Tractors 1735106Page Table of Contents Safety Rules & Information Operating Safety Safety Rules and Information Slope OperationSafety Rules & Information General OperationIgnition System Service & Maintenance Safe Handling of GasolineIdentification Numbers North AmericanCE Models OnlySafety Decals Safety DecalsDecal Operating Instructions, Models Decal Cutting Height Decal Cutting HeightCE Safety Icons Safety IconsControl Functions Throttle ControlChoke HeadlightsFeatures & Controls What is Automatic Controlled Traction? Parking Brake FunctionAutomatic Controlled Traction w/o 4WD Attachment Lift Control LeverVolt Power Outlet Dashboard Display & FunctionsDisplay Items FunctionsGeneral Operating Safety Operational Safety ChecksAdding Fuel Operating the Tractor Starting the EngineStopping the Tractor & Engine Driving The TractorMowing Mowing in ReverseAttachment Operation in Reverse Adjusting Mower Cutting Height Pushing the Tractor by HandMower Deck Removal & Installation Installing the Mower DeckSimplicity, Massey Ferguson or Agco Models Removing the Mower DeckSnapper Models Upper Hanger Upper Hole Lift Hook Lower Hole Long HubSimplicity, Massey Ferguson and Agco Models Pivoting Gauge Wheels Select ModelsMower Hitch Tractor Hitch Brackets Spring-Loaded Lever Snapper Models Attaching a Trailer StorageLift Variations When Using Attachments Hydraulic Lift ModelsManual Lift Models How and When to Water Fertilize & AerateHow High To Mow the Grass Tall Grass Requires Incremental CuttingWhen and How Often to Mow Lawn Care & Mowing InformationProper Mowing Speed Regular Maintenance Before Every Spring Each Hours 100 250 Fall UseRegular Maintenance Battery Maintenance Cleaning the Battery and CablesCheck Tire Pressures SizeLubrication GreaseOil Mower Lubrication Points Arbor Lubrication PointServicing the Mower Blabes Blade RemovalTransmission Maintenance K66 MaintenanceK664 Maintenance Transmission IdentificationK71 Maintenance Service Interval Every 5 HoursService Interval After 50 Hrs, Then Every 250 Hrs Transmission Oil Capacity Apx -1/2 qt 4.25 LInternal Transmission Filter Service Filter Access Cap Troubleshooting Adjustment, & Service TroubleshootingTroubleshooting, Adjustment, & Service Tractor TroubleshootingBattery Charging Seat AdjustmentManual Lift Assist Adjustment Steering Wheel Adjustment Steering Gear AdjustmentBrake Adjustment Thicker Spoke Faces SeatPTO Clutch Adjustment Mower AdjustmentsTransport Height & Ground Following Adjustment Select Models Gauge Wheels Select ModelsLeveling The Mower Leveling The Mower Side-to-Side, J-Hook Models LocknutMower Belt Replacement 44 & 50 PTO Belt ReplacementTo avoid damaging belts, do not PRY GapArbor Drive Belt Replacement 23 HP* Briggs & Stratton 25 HP* Kohler27 HP* Kohler K71Replacement Parts Maintenance ItemsOptional Accessories Technical Manuals

1700, 2700, 400 specifications

The Snapper series of mowers, including the Snapper 1700, 2700, and 400 models, represents a blend of power, efficiency, and innovative technology designed for lawn care enthusiasts and professionals alike. Each model offers unique features tailored to meet diverse mowing needs, ensuring top performance and ease of use.

The Snapper 1700 is ideal for residential yards and smaller properties. It is equipped with a reliable engine that delivers smooth, consistent power to tackle various grass types. The mower features a compact design, making it easy to maneuver around obstacles such as flower beds and trees. One of its standout attributes is the innovative easy-to-use height adjustment mechanism, allowing users to effortlessly change cutting heights to best suit their lawn conditions. Additionally, the Snapper 1700 boasts a robust cutting deck that ensures an even cut, resulting in a professional-grade finish.

The Snapper 2700 is a step up from the 1700, designed for users who require more power and capacity. This model comes with a larger cutting width, allowing for quicker mowing of expansive lawns. Enhanced features include an advanced mower deck technology that optimizes grass clipping discharge, helps to reduce clumping, and improves overall efficiency. The Snapper 2700 also incorporates ergonomic controls, providing comfort during prolonged use, and its durable construction ensures longevity. Furthermore, its rear-wheel drive system enhances traction, particularly on uneven terrain.

For those managing larger properties or commercial landscapes, the Snapper 400 offers premium performance and advanced technology. This model features a high-powered engine for maximum cutting performance, even in challenging conditions. The Snapper 400 is equipped with an intuitive digital display, providing essential information such as battery life and maintenance reminders, ensuring optimal performance over time. The mower's heavy-duty frame and reinforced deck enhance durability, making it suitable for rigorous tasks. It also boasts an innovative mulching capability, enabling users to finely chop grass clippings and return them to the soil as nutrient-rich mulch.

In summary, the Snapper 1700, 2700, and 400 models cater to a wide range of lawn care needs, from small yards to expansive landscapes. Each model combines innovative features, advanced technology, and durable construction, making them reliable choices for homeowners and professionals seeking superior mowing solutions.