Snapper 1700, 2700, 400 manual Gauge Wheels Select Models

Page 43

Gauge Wheels (Select Models)

The mower gauge wheels can be placed in several posi- tions depending on the height of cut. When using higher cutting heights, set the wheels in the lower position.

When using lower cutting heights, set the wheels in the upper position. To adjust:

PIVOTING GAUGE WHEELS

1.Remove the hair pin clip (A, B, Figure 46).

2.For upper position, install the pin (A) through the spindle above the bracket (C). For the lower position, push down on the top of the spindle, and install the hair pin clip (B) below the top of the bracket (C).

SLIDING BRACKET GAUGE WHEELS

1.Remove the nylock wing nut (A, Figure 47) from cap- screw (C). Slide out capscrew (C) from gauge wheel bracket (B). Change position of gauge wheel assem- bly to desired height.

2.Insert capscrew (C) through gauge wheel bracket (B) and gauge wheel assembly (D). Tighten nylock wing nut (A). Repeat steps 1 & 2 for all gauge wheels.

FIXED BRACKET GAUGE WHEELS

1.Remove the locknut (B, Figure 48), gauge wheel (C), washers (D), and shoulder bolt (E). Change position of gauge wheel to desired height.

2.Insert shoulder bolt (E) through washers (D) gauge wheel (C), and gauge wheel bracket (A). Secure with locknut (B). Repeat steps 1 & 2 for all gauge wheels.

Transport Height & Ground Following Adjustment (Select Models)

The transport height and ground following ability can be adjusted. Raising the trunnion (C, Figure 49) on the j- hook (A) will adjust the deck into the greatest ground fol- lowing ability and the lowest transport position, when the deck is lowered. Lowering the trunnion on the j-hook will give the highest transport position and decrease the deck’s ground following ability, when the deck is lowered.

1.Loosen jam nut (B, Figure 49).

2.Remove the hair pin (F) and washer (E) from trunnion

(C).

3.Remove the trunnion (C), j-hook (A) and jam nut (B) from tractor lift arm (D).

4.Turn trunnion (C) up or down to adjust height.

5.Place trunnion (C), j-hook (A) and jam nut (B) in trac- tor lift arm (D). Install washer (E) and hair pin (F). Tighten jam nut (B).

Troubleshooting, Adjustment, & Service

A

B

C

D

Figure 47. Sliding Bracket Gauge Wheel Adjustment

A.

Nylock Wing Nut

C. Capscrew

B.

Gauge Wheel Bracket

D. Gauge Wheel Assembly

A

B

D

E

C

Figure 48. Fixed Bracket Gauge Wheel Adjustment

A. Gauge Wheel Bracket

D. Washers

B. Locknut

E. Shoulder Bolt

C. Gauge Wheel

 

C

 

 

D

A

 

B

 

E

F

 

Figure 49. Cutting Height Adjustment

A. J-Hook

D. Tractor Lift Arm

B. Jam Nut

E. Washer

C. Trunnion

F. Hair Pin

41

Page 42 Page 44
Image 43
Page 42 Page 44
Contents 1735106 23HP Hydro Tractors Mower Decks25HP Hydro Tractors 27HP Hydro TractorsPage Table of Contents Safety Rules & Information Operating Safety Slope Operation Safety Rules and InformationGeneral Operation Safety Rules & InformationIgnition System Safe Handling of Gasoline Service & MaintenanceOnly Identification NumbersNorth American CE ModelsDecal Cutting Height Safety DecalsSafety Decals Decal Operating Instructions, Models Decal Cutting HeightSafety Icons CE Safety IconsHeadlights Control FunctionsThrottle Control ChokeFeatures & Controls Attachment Lift Control Lever What is Automatic Controlled Traction?Parking Brake Function Automatic Controlled Traction w/o 4WDFunctions Volt Power OutletDashboard Display & Functions Display ItemsOperational Safety Checks General Operating SafetyAdding Fuel Driving The Tractor Operating the TractorStarting the Engine Stopping the Tractor & EngineMowing in Reverse MowingAttachment Operation in Reverse Pushing the Tractor by Hand Adjusting Mower Cutting HeightRemoving the Mower Deck Mower Deck Removal & InstallationInstalling the Mower Deck Simplicity, Massey Ferguson or Agco ModelsUpper Hanger Upper Hole Lift Hook Lower Hole Long Hub Snapper ModelsPivoting Gauge Wheels Select Models Simplicity, Massey Ferguson and Agco ModelsMower Hitch Tractor Hitch Brackets Spring-Loaded Lever Snapper Models Storage Attaching a TrailerHydraulic Lift Models Lift Variations When Using AttachmentsManual Lift Models Tall Grass Requires Incremental Cutting How and When to WaterFertilize & Aerate How High To Mow the GrassLawn Care & Mowing Information When and How Often to MowProper Mowing Speed Before Every Spring Each Hours 100 250 Fall Use Regular MaintenanceRegular Maintenance Size Battery MaintenanceCleaning the Battery and Cables Check Tire PressuresGrease LubricationOil Arbor Lubrication Point Mower Lubrication PointsBlade Removal Servicing the Mower BlabesTransmission Identification Transmission MaintenanceK66 Maintenance K664 MaintenanceTransmission Oil Capacity Apx -1/2 qt 4.25 L K71 MaintenanceService Interval Every 5 Hours Service Interval After 50 Hrs, Then Every 250 HrsInternal Transmission Filter Service Filter Access Cap Troubleshooting Troubleshooting Adjustment, & ServiceTractor Troubleshooting Troubleshooting, Adjustment, & ServiceSeat Adjustment Battery ChargingManual Lift Assist Adjustment Thicker Spoke Faces Seat Steering Wheel AdjustmentSteering Gear Adjustment Brake AdjustmentMower Adjustments PTO Clutch AdjustmentGauge Wheels Select Models Transport Height & Ground Following Adjustment Select ModelsLeveling The Mower Side-to-Side, J-Hook Models Locknut Leveling The MowerGap Mower Belt Replacement44 & 50 PTO Belt Replacement To avoid damaging belts, do not PRYArbor Drive Belt Replacement K71 23 HP* Briggs & Stratton25 HP* Kohler 27 HP* KohlerTechnical Manuals Replacement PartsMaintenance Items Optional Accessories

1700, 2700, 400 specifications

The Snapper series of mowers, including the Snapper 1700, 2700, and 400 models, represents a blend of power, efficiency, and innovative technology designed for lawn care enthusiasts and professionals alike. Each model offers unique features tailored to meet diverse mowing needs, ensuring top performance and ease of use.

The Snapper 1700 is ideal for residential yards and smaller properties. It is equipped with a reliable engine that delivers smooth, consistent power to tackle various grass types. The mower features a compact design, making it easy to maneuver around obstacles such as flower beds and trees. One of its standout attributes is the innovative easy-to-use height adjustment mechanism, allowing users to effortlessly change cutting heights to best suit their lawn conditions. Additionally, the Snapper 1700 boasts a robust cutting deck that ensures an even cut, resulting in a professional-grade finish.

The Snapper 2700 is a step up from the 1700, designed for users who require more power and capacity. This model comes with a larger cutting width, allowing for quicker mowing of expansive lawns. Enhanced features include an advanced mower deck technology that optimizes grass clipping discharge, helps to reduce clumping, and improves overall efficiency. The Snapper 2700 also incorporates ergonomic controls, providing comfort during prolonged use, and its durable construction ensures longevity. Furthermore, its rear-wheel drive system enhances traction, particularly on uneven terrain.

For those managing larger properties or commercial landscapes, the Snapper 400 offers premium performance and advanced technology. This model features a high-powered engine for maximum cutting performance, even in challenging conditions. The Snapper 400 is equipped with an intuitive digital display, providing essential information such as battery life and maintenance reminders, ensuring optimal performance over time. The mower's heavy-duty frame and reinforced deck enhance durability, making it suitable for rigorous tasks. It also boasts an innovative mulching capability, enabling users to finely chop grass clippings and return them to the soil as nutrient-rich mulch.

In summary, the Snapper 1700, 2700, and 400 models cater to a wide range of lawn care needs, from small yards to expansive landscapes. Each model combines innovative features, advanced technology, and durable construction, making them reliable choices for homeowners and professionals seeking superior mowing solutions.
Top Page Image Contents