Snapper E281320BE, E331520KVE Service After First 5 Hours 3.2.4. Check Blade Drive Belt

Page 16

Section 3 - MAINTENANCE

WARNING

DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. STOP engine. STOP blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure away from plug. Engine and components are HOT. Avoid serious burns, allow all parts to cool before working on machine. Fuel Filler Cap and vent must be closed securely to prevent fuel spillage.

3.2 SERVICE - AFTER FIRST 5 HOURS 3.2.4. CHECK BLADE DRIVE BELT

The blade drive consists of a single belt from the engine to the deck. Inspect for signs of deterioration and proper tension.

1.Lower deck to lowest setting.

2.Remove four self-tapping screws, two on each side of mower drive belt cover. See Figure 3.3.

3.Slide cover back and rotate out on left side of mower deck.

REMOVE FOUR (4)

SELF-TAPPING

SCREWS

REMOVE COVER

FIGURE 3.3

4.Check belt for excessive wear or damage and replace if necessary; there are no adjustments on these models. See Figure 3.4.

WARNING

The following procedure requires the engine and blades to be operated. Exercise extreme caution. Clear area of loose parts & tools first. Only operate blades when seated in the operator’s seat.

28” & 33” MODELS (Dual Idler System)

ENGINE DRIVE PULLEY

SPINDLEASSEMBLY PULLEY

IDLER’S

FIGURE 3.4

3.2.5.BLADE BRAKE

1.Check blade brake for proper function. Blade should stop rotating in 3 seconds or less after moving the blade control lever to the “OFF” position or after releasing the blade pedals.

WARNING

Blades must stop rotating in 3 seconds or less after the blade has been turned off. DO NOT operate machine until blade brake has been adjusted and functioning properly.

2.If the blade continues to rotate longer than 3 seconds do not operate machine. Refer to Section “BLADE BRAKE ADJUSTMENT” or contact your SNAPPER dealer for assistance.

3.2.6.SERVICE BRAKE / PARK BRAKE

1.Check machine brake for proper function. Engage park brake. Push machine. Rear tires should skid. Drive machine forward and apply brake. Machine should come to a complete stop in less than 5 ft.

2.If brakes are not functioning properly brake adjustment must be completed before operating machine. Refer to Section “SERVICE BRAKE – PARK BRAKE ADJUSTMENT”.

3.2.7.INTERLOCK SYSTEM

Check interlock controls for proper function:

The engine MUST NOT start if:

1.Blade Control is “ON” and/or clutch/brake pedal is released.

The engine and blades MUST STOP if:

2.The operator leaves the operator position with Blade Control “ON” and/or clutch/brake pedal is released.

WARNING

DO NOT operate machine if interlock system is not functioning properly. Contact your SNAPPER dealer immediately for assistance.

16

Image 16
Contents European Rear Engine Riding Mower Series Manual No -3553 I.R /29/00Important Safety Instructions Operation Table of Contents Introduction NomenclatureFamiliarization Decals / Symbols Transmission Shift Lever Symbols Rabbit OPERATOR’S Seat Adjustment 2.2.1. Front to Rear Adjustment PRE-START Check ListStarting & Operation Engine Electric Start On NextEngine Electric Start Starting & OperationEngine Manual Start Starting & Operation 2.3.3. Mower Blade Wheel DriveStopping ENGINE, Wheel DRIVE, Blade 2.4.1. Engine Mower BladeStopping ENGINE, Wheel DRIVE, Blade 2.4.4. Park Brake Cutting Height AdjustmentDo not park the machine on slopes Reverse Lockout Mechanism Reverse Lockout Mechanism OverrideService Engine AIR Cleaner Check Mower Blade Service After First 5 HoursChange Engine OIL Service After First 5 Hours 3.2.4. Check Blade Drive Belt Service Brake / Park BrakeBlade Brake Interlock SystemService Every 25 Operating Hours Battery Fluid LevelClean Mower Deck Lubrication Grease FittingsFront Wheel Bearing Lubrication Rear Axle Bearing LubricationService Annually Fuel FilterEvery TWO Years Storage OUT of SeasonRemoving Fuel Tank Engine Adjustments & Repair Blade Brake AdjustmentFront to Rear Levelness 28, & 33 Decks Mower Deck AdjustmentFront to Rear Levelness 30 Decks Adjustments & Repair Wheel Brake AdjustmentChain Case Mower Blade Replacement 4.4.1. Blade Wear Limits Blade SharpeningBelt Replacement Blade Drive Belt ReplacementBelt Removal Battery Battery Removal Battery InstallationBattery Service Battery StorageBattery Testing NEW Battery Preparation 1. Remove battery from cartonSnapper Rear Engine Rider Accessories Problem Probable Cause Corrective Action StopLoss Of Traction Blades Not CuttingCutting Grass ImproperlySubject Service Reference Power LWATo be Performed Pages Vibration Max Less ThanMAINTENANCE/REPLACEMENT Parts Maintenance Parts Year Limited Warranty Disclaimer of WarrantyService Notes Service Notes Service Notes European Rear Engine Riding Mower Series

E281320BE, E331520KVE specifications

The Snapper E281320BE and E331520KVE are two robust lawn mowers that stand out in the market for their innovative features and advanced technologies. Both models are designed to provide an efficient and comfortable mowing experience, catering to the needs of homeowners and professionals alike.

Starting with the Snapper E281320BE, this model is powered by a reliable 21-inch steel cutting deck that ensures a clean and precise cut every time. Its 20-inch rear wheel drive allows for exceptional maneuverability, making it ideal for navigating tight spaces and uneven terrain. The E281320BE is equipped with a powerful 223cc engine, providing ample power for tackling thick grass and challenging landscapes. This model also offers a three-in-one cutting capability, allowing users to choose between mulching, bagging, or side discharge modes, providing versatility for different mowing conditions.

On the other hand, the Snapper E331520KVE enhances performance with its 33-inch cutting deck, making it suitable for larger lawns while still maintaining excellent cutting efficiency. Featuring a strong 344cc engine, this mower delivers reliable power that can handle heavier workloads. Equipped with a high-back seat and ergonomic controls, the E331520KVE ensures comfortable operation over extended periods, reducing fatigue for the user.

Both models boast Snapper’s innovative Toro-branded SmartChoke technology, which simplifies starting and improves engine performance in various weather conditions. Users will appreciate the easy-to-use height adjustment lever, allowing for quick changes in cutting height to achieve the desired grass length.

The durability of these mowers is reinforced by their steel frame construction, ensuring they withstand the rigours of regular use. Additionally, Snapper has integrated features like a reinforced front bumper and heavy-duty wheels, enhancing stability and traction during operation.

In terms of maintenance, both models are designed for convenience, with easy access to the engine and other components, allowing for straightforward servicing. The Snapper E281320BE and E331520KVE also come with a solid warranty, showcasing the manufacturer’s commitment to quality.

In summary, Snapper's E281320BE and E331520KVE lawn mowers are exceptional choices for those seeking reliability, efficiency, and innovative features in their mowing equipment. With their powerful engines, versatile cutting options, and user-friendly designs, these mowers are set to meet a wide range of lawn care needs.