Snapper E281320BE, E331520KVE Lubrication Grease Fittings, Service Every 25 Operating Hours

Page 17

Section 3 - MAINTENANCE

3.2.8.REVERSE LOCKOUT MECHANISM

Check function of Reverse Lockout Mechanism with engine off.

1.Depress and hold blade pedals.

2.Depress and hold clutch/brake pedal.

3.Shift lever must not go into reverse.

WARNING

DO NOT operate machine if Reverse Lockout Mechanism is not functioning properly. Contact your SNAPPER dealer immediately for assistance.

3.2.9.LUBRICATION – GREASE FITTINGS

The following components on the Rear Engine Rider are equipped with grease fittings and require periodic lubrication. Apply General Purpose grease (NLGI No.2) with a grease gun.

1.Front Wheel Bearings. Refer to Section

“FRONT WHEEL BEARINGS – LUBRICATION”.

2.Rear Axle Bearing. Refer to Section “REAR

AXLE BEARING – LUBRICATION”.

3.Mower Blade Spindle. Refer to Section

“MOWER BLADE SPINDLE – LUBRICATION”.

3.3 SERVICE - EVERY 25 OPERATING HOURS

3.3.1.Perform all service required after the first 5 hours of operation. Refer to Section “SERVICE – AFTER 5 HOURS”.

WARNING

DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. Stop engine. Stop blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure away from plug. Engine and components are HOT. Avoid serious burns, allow all parts to cool before working on machine. Fuel Filler Cap and Vent must be closed securely to prevent fuel spillage.

3.3.2.BATTERY FLUID LEVEL

1.Remove battery. Refer to Section “BATTERY REMOVAL”.

2.Remove battery caps. Check fluid level.

3.Add water only to bring fluid to proper level – approximately 3/16” above plates.

DO NOT OVERFILL.

4.Reinstall battery. Refer to Section “BATTERY INSTALLATION”.

3.3.3.MOWER DECK LEVELNESS

Check mower deck for proper level. Adjust as required. Refer to Section “MOWER DECK ADJUSTMENT –

LEVELNESS”.

3.3.4.CLEAN MOWER DECK

1.Follow WARNING statement found on this page.

2.Check fuel level in tank. If over 3/4 full, remove tank. Refer to Section “REMOVING FUEL TANK”. If 3/4 or less, proceed to next step.

3.Carefully stand Rear Engine Rider on rear bumper.

4.Clean underside of mower deck, removing all accumulation of grass clippings and debris.

5.Clean top of deck, removing all grass clippings and debris.

3.3.5MOWER BLADE SPINDLE - LUBRICATION

1.Follow WARNING statement found on this page.

2.Check fuel level in tank. If over 3/4 full, remove tank. Refer to Section “FUEL TANK REMOVAL”. If 3/4 or less, proceed to next step.

3.Carefully stand Rear Engine Rider on rear bumper.

4.Lubricate spindle with three shots of general purpose grease from grease gun. See Figure 3.5.

IMPORTANT: If the Rear Engine Rider will be on its rear bumper for longer than two hours, remove the battery. Refer to Section “BATTERY REMOVAL”.

3.3.6.MOWER DECK LINKAGE - LUBRICATION Lubricate all mower deck linkage pivot points with a light coat of motor oil.

SPINDLE

GREASE FITTING

FIGURE 3.5

17

Image 17
Contents Manual No -3553 I.R /29/00 European Rear Engine Riding Mower SeriesImportant Safety Instructions Operation Table of Contents Nomenclature IntroductionFamiliarization Decals / Symbols Transmission Shift Lever Symbols Rabbit PRE-START Check List OPERATOR’S Seat Adjustment 2.2.1. Front to Rear AdjustmentOn Next Starting & Operation Engine Electric StartEngine Manual Start Starting & OperationEngine Electric Start Wheel Drive Starting & Operation 2.3.3. Mower BladeMower Blade Stopping ENGINE, Wheel DRIVE, Blade 2.4.1. EngineDo not park the machine on slopes Cutting Height AdjustmentStopping ENGINE, Wheel DRIVE, Blade 2.4.4. Park Brake Reverse Lockout Mechanism Override Reverse Lockout MechanismChange Engine OIL Service After First 5 HoursService Engine AIR Cleaner Check Mower Blade Service Brake / Park Brake Service After First 5 Hours 3.2.4. Check Blade Drive BeltBlade Brake Interlock SystemBattery Fluid Level Service Every 25 Operating HoursClean Mower Deck Lubrication Grease FittingsRear Axle Bearing Lubrication Front Wheel Bearing LubricationFuel Filter Service AnnuallyEvery TWO Years Storage OUT of SeasonRemoving Fuel Tank Blade Brake Adjustment Engine Adjustments & RepairFront to Rear Levelness 30 Decks Mower Deck AdjustmentFront to Rear Levelness 28, & 33 Decks Wheel Brake Adjustment Adjustments & RepairChain Case Blade Sharpening Mower Blade Replacement 4.4.1. Blade Wear LimitsBelt Removal Blade Drive Belt ReplacementBelt Replacement Battery Installation Battery Battery RemovalBattery Storage Battery ServiceBattery Testing NEW Battery Preparation 1. Remove battery from cartonSnapper Rear Engine Rider Accessories Stop Problem Probable Cause Corrective ActionBlades Not Cutting Loss Of TractionCutting Grass ImproperlyPower LWA Subject Service ReferenceTo be Performed Pages Vibration Max Less ThanMAINTENANCE/REPLACEMENT Parts Maintenance Parts Disclaimer of Warranty Year Limited WarrantyService Notes Service Notes Service Notes European Rear Engine Riding Mower Series

E281320BE, E331520KVE specifications

The Snapper E281320BE and E331520KVE are two robust lawn mowers that stand out in the market for their innovative features and advanced technologies. Both models are designed to provide an efficient and comfortable mowing experience, catering to the needs of homeowners and professionals alike.

Starting with the Snapper E281320BE, this model is powered by a reliable 21-inch steel cutting deck that ensures a clean and precise cut every time. Its 20-inch rear wheel drive allows for exceptional maneuverability, making it ideal for navigating tight spaces and uneven terrain. The E281320BE is equipped with a powerful 223cc engine, providing ample power for tackling thick grass and challenging landscapes. This model also offers a three-in-one cutting capability, allowing users to choose between mulching, bagging, or side discharge modes, providing versatility for different mowing conditions.

On the other hand, the Snapper E331520KVE enhances performance with its 33-inch cutting deck, making it suitable for larger lawns while still maintaining excellent cutting efficiency. Featuring a strong 344cc engine, this mower delivers reliable power that can handle heavier workloads. Equipped with a high-back seat and ergonomic controls, the E331520KVE ensures comfortable operation over extended periods, reducing fatigue for the user.

Both models boast Snapper’s innovative Toro-branded SmartChoke technology, which simplifies starting and improves engine performance in various weather conditions. Users will appreciate the easy-to-use height adjustment lever, allowing for quick changes in cutting height to achieve the desired grass length.

The durability of these mowers is reinforced by their steel frame construction, ensuring they withstand the rigours of regular use. Additionally, Snapper has integrated features like a reinforced front bumper and heavy-duty wheels, enhancing stability and traction during operation.

In terms of maintenance, both models are designed for convenience, with easy access to the engine and other components, allowing for straightforward servicing. The Snapper E281320BE and E331520KVE also come with a solid warranty, showcasing the manufacturer’s commitment to quality.

In summary, Snapper's E281320BE and E331520KVE lawn mowers are exceptional choices for those seeking reliability, efficiency, and innovative features in their mowing equipment. With their powerful engines, versatile cutting options, and user-friendly designs, these mowers are set to meet a wide range of lawn care needs.