Snapper E281320BE, E331520KVE Adjustments & Repair, Wheel Brake Adjustment

Page 23

SECTION 4 - ADJUSTMENTS & REPAIR

FLOOR

SHOWN WITH COVER REMOVED

 

HANGER

HAIR PIN

CHAIN PIVOT

SUPPORT

BRACKET

HANGER

CHAIN

FIGURE 4.4

WARNING

DO NOT attempt any adjustments, maintenance, service or repairs with the engine running. STOP engine. STOP blade. Engage parking brake. Remove key. Remove spark plug wire from spark plug and secure away from plug. Engine and components are HOT. Avoid serious burns, allow all parts to cool before working on machine. Fuel Filler Cap and vent must be closed securely to prevent fuel spillage.

4.2.4.CUTTING HEIGHT ADJUSTMENT The deck cutting height range may be adjusted.

1. Place the Rear Engine Rider on a smooth, level surface.

2. Move deck lift lever to the lowest cutting position.

3. Loosen the two lift quadrant mounting bolts and eccentric bolt. See Figure 4.5.

RAISE OR

LOWER LIFT

QUADRANT

AS DESIRED

LOOSEN

 

 

MOUNTING

 

ROTATE

BOLTS

 

 

ECCENTRIC

 

 

 

 

 

 

 

 

LOOSEN

ECCENTRIC

BOLT

FIGURE 4.5

4.Rotate eccentric to raise or lower desired cutting height range.

5.Tighten lift quadrant mounting bolts and eccentric bolt.

NOTE: Lift quadrant in lowest position gives 1” to 3 1/2” cutting height range. Lift quadrant in highest position gives 1-1/2” to 4” cutting height range.

4.3REAR ENGINE RIDER DRIVE COMPONENTS Your Snapper rider is equipped with a patented smooth start clutch. The clutch should operate smoothly and provide ample traction. If problems are experienced, contact your Snapper dealer for repair.

4.3.1. WHEEL BRAKE ADJUSTMENT

Test the wheel brake on a dry concrete surface. When properly adjusted, the Rear Engine Rider will stop within 5 feet from fastest speed. If stopping distance is more than 5 feet, the wheel brake should be adjusted as follows:

1.Follow WARNING statement found on this page.

2.Check fuel level in tank. If over 3/4 full, remove tank. Refer to Section “REMOVING FUEL TANK”. If 3/4 or less, proceed to next step.

3.Carefully stand Rear Engine Rider on rear bumper.

(Continued on next page)

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Manual No -3553 I.R /29/00 European Rear Engine Riding Mower SeriesImportant Safety Instructions Operation Table of Contents Nomenclature IntroductionFamiliarization Decals / Symbols Transmission Shift Lever Symbols Rabbit PRE-START Check List OPERATOR’S Seat Adjustment 2.2.1. Front to Rear AdjustmentOn Next Starting & Operation Engine Electric StartEngine Manual Start Starting & OperationEngine Electric Start Wheel Drive Starting & Operation 2.3.3. Mower BladeMower Blade Stopping ENGINE, Wheel DRIVE, Blade 2.4.1. EngineDo not park the machine on slopes Cutting Height AdjustmentStopping ENGINE, Wheel DRIVE, Blade 2.4.4. Park Brake Reverse Lockout Mechanism Override Reverse Lockout MechanismChange Engine OIL Service After First 5 HoursService Engine AIR Cleaner Check Mower Blade Interlock System Service After First 5 Hours 3.2.4. Check Blade Drive BeltService Brake / Park Brake Blade BrakeLubrication Grease Fittings Service Every 25 Operating HoursBattery Fluid Level Clean Mower DeckRear Axle Bearing Lubrication Front Wheel Bearing LubricationStorage OUT of Season Service AnnuallyFuel Filter Every TWO YearsRemoving Fuel Tank Blade Brake Adjustment Engine Adjustments & RepairFront to Rear Levelness 30 Decks Mower Deck AdjustmentFront to Rear Levelness 28, & 33 Decks Wheel Brake Adjustment Adjustments & RepairChain Case Blade Sharpening Mower Blade Replacement 4.4.1. Blade Wear LimitsBelt Removal Blade Drive Belt ReplacementBelt Replacement Battery Installation Battery Battery RemovalNEW Battery Preparation 1. Remove battery from carton Battery ServiceBattery Storage Battery TestingSnapper Rear Engine Rider Accessories Stop Problem Probable Cause Corrective ActionImproperly Loss Of TractionBlades Not Cutting Cutting GrassVibration Max Less Than Subject Service ReferencePower LWA To be Performed PagesMAINTENANCE/REPLACEMENT Parts Maintenance Parts Disclaimer of Warranty Year Limited WarrantyService Notes Service Notes Service Notes European Rear Engine Riding Mower Series

E281320BE, E331520KVE specifications

The Snapper E281320BE and E331520KVE are two robust lawn mowers that stand out in the market for their innovative features and advanced technologies. Both models are designed to provide an efficient and comfortable mowing experience, catering to the needs of homeowners and professionals alike.

Starting with the Snapper E281320BE, this model is powered by a reliable 21-inch steel cutting deck that ensures a clean and precise cut every time. Its 20-inch rear wheel drive allows for exceptional maneuverability, making it ideal for navigating tight spaces and uneven terrain. The E281320BE is equipped with a powerful 223cc engine, providing ample power for tackling thick grass and challenging landscapes. This model also offers a three-in-one cutting capability, allowing users to choose between mulching, bagging, or side discharge modes, providing versatility for different mowing conditions.

On the other hand, the Snapper E331520KVE enhances performance with its 33-inch cutting deck, making it suitable for larger lawns while still maintaining excellent cutting efficiency. Featuring a strong 344cc engine, this mower delivers reliable power that can handle heavier workloads. Equipped with a high-back seat and ergonomic controls, the E331520KVE ensures comfortable operation over extended periods, reducing fatigue for the user.

Both models boast Snapper’s innovative Toro-branded SmartChoke technology, which simplifies starting and improves engine performance in various weather conditions. Users will appreciate the easy-to-use height adjustment lever, allowing for quick changes in cutting height to achieve the desired grass length.

The durability of these mowers is reinforced by their steel frame construction, ensuring they withstand the rigours of regular use. Additionally, Snapper has integrated features like a reinforced front bumper and heavy-duty wheels, enhancing stability and traction during operation.

In terms of maintenance, both models are designed for convenience, with easy access to the engine and other components, allowing for straightforward servicing. The Snapper E281320BE and E331520KVE also come with a solid warranty, showcasing the manufacturer’s commitment to quality.

In summary, Snapper's E281320BE and E331520KVE lawn mowers are exceptional choices for those seeking reliability, efficiency, and innovative features in their mowing equipment. With their powerful engines, versatile cutting options, and user-friendly designs, these mowers are set to meet a wide range of lawn care needs.
Top Page Image Contents