Snapper E281320BE, E331520KVE Problem Probable Cause Corrective Action, Stop

Page 30

TROUBLESHOOTING

PROBLEM

 

PROBABLE CAUSE

 

CORRECTIVE ACTION

 

 

 

 

Engine Will Not

1. Fuel tank empty.

1.

Fill fuel tank with fresh fuel to proper level.

Start Using

2. Engine needs choking.

2.

Move choke control to “CHOKE” position.

Recoil Starter

3. Spark plug wire disconnected.

3.

Place spark plug wire onto spark plug.

 

4.

Faulty parking brake, blade or ignition switch.

4.

Contact authorized SNAPPER dealer.

 

5.

Park brake not engaged.

5.

Engage park brake.

 

6.

Ignition is in the OFF position.

6.

Turn ignition switch to the RUN position.

Engine Will Not

1. Fuel tank empty.

1.

Fill fuel tank with fresh fuel to proper level.

Start Using

2. Engine needs choking.

2.

Move choke control to “CHOKE” position.

Electric Starter

3. Spark plug wire disconnected.

3.

Place spark plug wire onto spark plug.

 

4.

Faulty parking brake, blade or ignition switch.

4.

Contact authorized SNAPPER dealer.

 

5.

Park brake not engaged.

5.

Engage park brake.

 

6.

Blown Fuse.

6.

Replace with new 20 AMP fuse.

 

7.

Faulty interlock module.

7.

Contact authorized SNAPPER dealer.

 

8.

Ignition is in the OFF position.

8.

Turn ignition switch to the START position.

 

9.

Battery is weak or dead.

9. Charge or replace with new battery.

 

10. Battery cables loose, broken disconnected or

10. Clean and connect battery cables. If

 

 

corroded.

 

broken, replace with new battery cables.

 

11. Faulty electric starter or starter solenoid.

11. Contact authorized SNAPPER dealer.

 

12. Starter cable loose, broken or disconnected

12. Connect starter cable. If broken, replace

 

 

 

 

with new starter cable.

 

13. Electrical wiring harness disconnected or broken.

13. Connect or replace with new wiring harness.

Engine Stalls After

1. Operator not in seat.

1.

Sit in operator’s seat.

Running

2. Choke control in the “CHOKE” position.

2. Move choke control to “OFF” position.

 

3.

Fuel tank empty.

3.

Fill fuel tank with fresh fuel to proper level.

 

4.

Engine air pre-cleaner and or air cleaner dirty.

4.

Clean free of all debris.

 

5.

Spark plug defective or gap set improperly.

5.

Service spark plug.

 

6.

Fuel filter restricted.

6.

Replace fuel filter.

 

7.

Water, debris or stale fuel in fuel system.

7.

Drain and clean fuel system.

 

8.

Vent on Fuel Cap closed.

8.

Open vent.

Engine Loses

1. Excessive load on engine.

1.

Lessen load.

Power

2. Engine air pre-cleaner or air cleaner dirty

2.

Clean or replace filters.

 

3.

Spark plug faulty.

3.

Service spark plug.

 

4.

Water, debris or stale fuel in fuel system.

4.

Drain and clean fuel system. Replace filter.

 

5.

Debris build up on engine cooling screen.

5. Clean all debris from engine cooling screen.

Engine Backfires

1. Throttle control set too “FAST”.

1. Set throttle control to “SLOW” and allow

When Turned To

 

 

 

engine to idle. Then, turn key to “OFF”.

“STOP”

 

 

 

 

Excessive Vibration

1. Damaged, out of balance or bent mower blades.

1.

Service mower blade(s).

 

2.

Loose blade components.

2.

Service and tighten loose parts.

 

3.

Loose or missing air lift (if equipped).

3.

Replace air lifts. Tighten to proper torque.

 

4.

Lumpy or frayed belt

4.

Replace belt.

 

5.

Bent Idler, stationary or spindle pulley

5.

Replace pulley.

(Trouble Shooting Continued on Next Page)

30

Image 30
Contents European Rear Engine Riding Mower Series Manual No -3553 I.R /29/00Important Safety Instructions Operation Table of Contents Introduction NomenclatureFamiliarization Decals / Symbols Transmission Shift Lever Symbols Rabbit OPERATOR’S Seat Adjustment 2.2.1. Front to Rear Adjustment PRE-START Check ListStarting & Operation Engine Electric Start On NextStarting & Operation Engine Electric StartEngine Manual Start Starting & Operation 2.3.3. Mower Blade Wheel DriveStopping ENGINE, Wheel DRIVE, Blade 2.4.1. Engine Mower BladeCutting Height Adjustment Stopping ENGINE, Wheel DRIVE, Blade 2.4.4. Park BrakeDo not park the machine on slopes Reverse Lockout Mechanism Reverse Lockout Mechanism OverrideService After First 5 Hours Service Engine AIR Cleaner Check Mower BladeChange Engine OIL Blade Brake Service After First 5 Hours 3.2.4. Check Blade Drive BeltService Brake / Park Brake Interlock SystemClean Mower Deck Service Every 25 Operating HoursBattery Fluid Level Lubrication Grease FittingsFront Wheel Bearing Lubrication Rear Axle Bearing LubricationEvery TWO Years Service AnnuallyFuel Filter Storage OUT of SeasonRemoving Fuel Tank Engine Adjustments & Repair Blade Brake AdjustmentMower Deck Adjustment Front to Rear Levelness 28, & 33 DecksFront to Rear Levelness 30 Decks Adjustments & Repair Wheel Brake AdjustmentChain Case Mower Blade Replacement 4.4.1. Blade Wear Limits Blade SharpeningBlade Drive Belt Replacement Belt ReplacementBelt Removal Battery Battery Removal Battery InstallationBattery Testing Battery ServiceBattery Storage NEW Battery Preparation 1. Remove battery from cartonSnapper Rear Engine Rider Accessories Problem Probable Cause Corrective Action StopCutting Grass Loss Of TractionBlades Not Cutting ImproperlyTo be Performed Pages Subject Service ReferencePower LWA Vibration Max Less ThanMAINTENANCE/REPLACEMENT Parts Maintenance Parts Year Limited Warranty Disclaimer of WarrantyService Notes Service Notes Service Notes European Rear Engine Riding Mower Series

E281320BE, E331520KVE specifications

The Snapper E281320BE and E331520KVE are two robust lawn mowers that stand out in the market for their innovative features and advanced technologies. Both models are designed to provide an efficient and comfortable mowing experience, catering to the needs of homeowners and professionals alike.

Starting with the Snapper E281320BE, this model is powered by a reliable 21-inch steel cutting deck that ensures a clean and precise cut every time. Its 20-inch rear wheel drive allows for exceptional maneuverability, making it ideal for navigating tight spaces and uneven terrain. The E281320BE is equipped with a powerful 223cc engine, providing ample power for tackling thick grass and challenging landscapes. This model also offers a three-in-one cutting capability, allowing users to choose between mulching, bagging, or side discharge modes, providing versatility for different mowing conditions.

On the other hand, the Snapper E331520KVE enhances performance with its 33-inch cutting deck, making it suitable for larger lawns while still maintaining excellent cutting efficiency. Featuring a strong 344cc engine, this mower delivers reliable power that can handle heavier workloads. Equipped with a high-back seat and ergonomic controls, the E331520KVE ensures comfortable operation over extended periods, reducing fatigue for the user.

Both models boast Snapper’s innovative Toro-branded SmartChoke technology, which simplifies starting and improves engine performance in various weather conditions. Users will appreciate the easy-to-use height adjustment lever, allowing for quick changes in cutting height to achieve the desired grass length.

The durability of these mowers is reinforced by their steel frame construction, ensuring they withstand the rigours of regular use. Additionally, Snapper has integrated features like a reinforced front bumper and heavy-duty wheels, enhancing stability and traction during operation.

In terms of maintenance, both models are designed for convenience, with easy access to the engine and other components, allowing for straightforward servicing. The Snapper E281320BE and E331520KVE also come with a solid warranty, showcasing the manufacturer’s commitment to quality.

In summary, Snapper's E281320BE and E331520KVE lawn mowers are exceptional choices for those seeking reliability, efficiency, and innovative features in their mowing equipment. With their powerful engines, versatile cutting options, and user-friendly designs, these mowers are set to meet a wide range of lawn care needs.