Snapper E281320BE, E331520KVE Battery Service, Battery Storage, Battery Testing

Page 28

Section 4 - ADJUSTMENTS & REPAIR

WARNING

The electrolyte (acid) produces a highly explosive gas. Keep all sparks, flame and fire away from area when charging battery or when handling electrolyte or battery. Electrolyte (acid) is a highly corrosive liquid. Wear eye protection. Wash affected areas immediately after having eye or skin contact with electrolyte (acid). Battery acid is corrosive. Rinse empty acid containers with water and mutilate before discarding. If acid is spilled on battery, bench, or clothing, etc., Flush with clear water and neutralize with baking soda.

4.6.3. BATTERY SERVICE

1.Remove battery. Refer to Section “BATTERY REMOVAL”.

2.Place battery in a well ventilated area on a level surface.

3.Using distilled water, refill cells as required to cover cell plates of which can also be visualized through the plastic battery case.

4.With cell caps removed, connect battery charger to battery terminals. Red to positive (+) terminal and black to negative (-) terminal.

5.Slow charge battery at 1 amp for 10 hours.

6.If battery will not accept charge or is partially charged after 10 hours of charging at 1 amp, replace with new battery.

4.6.4. BATTERY STORAGE

If mower is to be stored out of season on its rear bumper, it is recommended the battery be removed, charged and stored.

1.Remove battery. Refer to Section “BATTERY REMOVAL”.

2.Perform battery service.

3.Bring battery to full charge, if required.

4.Store battery in an area away from the RIDER on a wood surface. DO NOT STORE BATTERY ON A CONCRETE SURFACE.

4.6.5.BATTERY TESTING

There are two types of battery tests: Unloaded and Loaded. The unloaded test is the procedure that will be discussed. It’s the simplest and most commonly used. An unloaded test is made on a battery without discharging current. To perform unloaded testing, check charge condition using either a hydrometer or voltmeter.

1.Using a voltmeter, voltage readings appear instantly to show the state of charge. Remember to hook the positive lead to the battery’s positive terminal, and the negative lead to the negative terminal.

2.A hydrometer measures the specific gravity of each cell. The specific gravity tells the degree of charge; generally, a specific gravity of about 1.265 to 1.280 indicates full charge. A reading of 1.230 to 1.260 indicates the battery should be charged. The chart on the next page shows the charge level as measured by syringe float hydrometer, digital voltmeter and five ball hydrometer.

4.6.6.NEW BATTERY PREPARATION 1. Remove battery from carton.

2. Place battery in a well ventilated area on a level non-concrete surface.

3. Remove battery cell caps. Fill cells as required with electrolyte (purchased separately) to proper level. Fill to 3/16” above cell plates. Filling battery with electrolyte will bring the battery to 80% charged state.

4. With cell caps removed, connect battery charger to battery terminals; RED to positive (+) and BLACK to negative (-) terminal.

IMPORTANT: 3/16” above cell plates is the recommended level. DO NOT place anything in battery other than specified electrolyte.

WARNING

DO NOT attempt to charge battery while installed on the Riding Mower. DO NOT use “BOOST” chargers on the battery. DO NOT OVERFILL!

5.Slow charge the battery at 1 amp for 2 hours to bring the battery to full charge.

6.After charging, check level of electrolyte and add as needed to bring level to 3/16” above cell plates.

7.Reinstall cell caps.

8.Remove the hair pin and swivel from the deck support to allow clearance for battery installation.

9.Slide battery partially into battery housing.

10.Connect positive (+) cable (red) first, from wiring harness to the positive terminal (+) on battery using bolt and nut provided in hardware bag. Connect negative (-) cable (black) last, to negative terminal (-) on battery using bolt and nut. Apply a small amount of grease over terminals to prevent corrosion.

11.Insert battery completely into battery housing.

12.Reinstall battery cover. See Figure 4.15.

13.Reinstall swivel and hair pin for deck support.

WARNING

Shield the positive terminal with terminal cover located on battery harness. This prevents metal from touching the positive terminal which could cause sparks.

(Battery Testing Chart on Next Page)

28

Page 27 Page 29
Image 28
Page 27 Page 29
Contents European Rear Engine Riding Mower Series Manual No -3553 I.R /29/00Important Safety Instructions Operation Table of Contents Introduction NomenclatureFamiliarization Decals / Symbols Transmission Shift Lever Symbols Rabbit OPERATOR’S Seat Adjustment 2.2.1. Front to Rear Adjustment PRE-START Check ListStarting & Operation Engine Electric Start On NextEngine Electric Start Starting & OperationEngine Manual Start Starting & Operation 2.3.3. Mower Blade Wheel DriveStopping ENGINE, Wheel DRIVE, Blade 2.4.1. Engine Mower BladeStopping ENGINE, Wheel DRIVE, Blade 2.4.4. Park Brake Cutting Height AdjustmentDo not park the machine on slopes Reverse Lockout Mechanism Reverse Lockout Mechanism OverrideService Engine AIR Cleaner Check Mower Blade Service After First 5 HoursChange Engine OIL Service After First 5 Hours 3.2.4. Check Blade Drive Belt Service Brake / Park BrakeBlade Brake Interlock SystemService Every 25 Operating Hours Battery Fluid LevelClean Mower Deck Lubrication Grease FittingsFront Wheel Bearing Lubrication Rear Axle Bearing LubricationService Annually Fuel FilterEvery TWO Years Storage OUT of SeasonRemoving Fuel Tank Engine Adjustments & Repair Blade Brake AdjustmentFront to Rear Levelness 28, & 33 Decks Mower Deck AdjustmentFront to Rear Levelness 30 Decks Adjustments & Repair Wheel Brake AdjustmentChain Case Mower Blade Replacement 4.4.1. Blade Wear Limits Blade SharpeningBelt Replacement Blade Drive Belt ReplacementBelt Removal Battery Battery Removal Battery InstallationBattery Service Battery StorageBattery Testing NEW Battery Preparation 1. Remove battery from cartonSnapper Rear Engine Rider Accessories Problem Probable Cause Corrective Action StopLoss Of Traction Blades Not CuttingCutting Grass ImproperlySubject Service Reference Power LWATo be Performed Pages Vibration Max Less ThanMAINTENANCE/REPLACEMENT Parts Maintenance Parts Year Limited Warranty Disclaimer of WarrantyService Notes Service Notes Service Notes European Rear Engine Riding Mower Series

E281320BE, E331520KVE specifications

The Snapper E281320BE and E331520KVE are two robust lawn mowers that stand out in the market for their innovative features and advanced technologies. Both models are designed to provide an efficient and comfortable mowing experience, catering to the needs of homeowners and professionals alike.

Starting with the Snapper E281320BE, this model is powered by a reliable 21-inch steel cutting deck that ensures a clean and precise cut every time. Its 20-inch rear wheel drive allows for exceptional maneuverability, making it ideal for navigating tight spaces and uneven terrain. The E281320BE is equipped with a powerful 223cc engine, providing ample power for tackling thick grass and challenging landscapes. This model also offers a three-in-one cutting capability, allowing users to choose between mulching, bagging, or side discharge modes, providing versatility for different mowing conditions.

On the other hand, the Snapper E331520KVE enhances performance with its 33-inch cutting deck, making it suitable for larger lawns while still maintaining excellent cutting efficiency. Featuring a strong 344cc engine, this mower delivers reliable power that can handle heavier workloads. Equipped with a high-back seat and ergonomic controls, the E331520KVE ensures comfortable operation over extended periods, reducing fatigue for the user.

Both models boast Snapper’s innovative Toro-branded SmartChoke technology, which simplifies starting and improves engine performance in various weather conditions. Users will appreciate the easy-to-use height adjustment lever, allowing for quick changes in cutting height to achieve the desired grass length.

The durability of these mowers is reinforced by their steel frame construction, ensuring they withstand the rigours of regular use. Additionally, Snapper has integrated features like a reinforced front bumper and heavy-duty wheels, enhancing stability and traction during operation.

In terms of maintenance, both models are designed for convenience, with easy access to the engine and other components, allowing for straightforward servicing. The Snapper E281320BE and E331520KVE also come with a solid warranty, showcasing the manufacturer’s commitment to quality.

In summary, Snapper's E281320BE and E331520KVE lawn mowers are exceptional choices for those seeking reliability, efficiency, and innovative features in their mowing equipment. With their powerful engines, versatile cutting options, and user-friendly designs, these mowers are set to meet a wide range of lawn care needs.
Top Page Image Contents