Snapper ERP217019BV important safety instructions Recycling Operation

Page 10

Section 2 - OPERATING INSTRUCTIONS

WARNING

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.

2.9INSTALLATION of DISCHARGE DEFLECTOR (Optional accessory on some models)

Install discharge deflector if discharging is desired. Grass Bag and Bag Adapter or Recycling Cover must be removed.

1.Remove front and rear nuts that secure Bag Adapter or Recycling Cover to deck. Refer to sections concerning these parts.

2.Install discharge deflector and secure to deck using hardware removed in Step 1. Slot in front edge of discharge deflector must be under nut as shown and both bolts protruding through holes in the side of the deflector. Secure nuts to the side of deflector. Tighten nuts securely. See Figure 2.13.

INSTALL

 

SLIDE

DISCHARGE

 

DEFLECTOR

DEFLECTOR

 

SLOT

 

 

 

INSTALL

NUTS

FIGURE 2.13

2.10INSTALLATION of RECYCLING COVER (Optional Accessory on Some Models)

It will be necessary to remove bag adapter and grass bag or discharge deflector before installing recycling cover. See previous section for instructions. Install the recycling cover and secure to the side and top of the deck with the two nuts provided on the machine. Slide top portion of cover under nut secured to the deck. See Figure 2.14.

RECYCLING

COVER

INSTALL RECYCLING

COVER TO THE DECK

USING THE TWO NUTS

FIGURE 2.14

2.11 RECYCLING OPERATION

NOTE: For best recycling results, cut up to a maximum of 1/3 of grass blade length and recycle ONLY when grass is dry.

1.Set all wheels in the highest cutting position (Notch 7).

2.Move engine speed control to “FAST” (Rabbit) position.

3.Move ground speed control to slowest speed setting.

4.Proceed mowing slowly. If grass is very dense, lower each rear wheel latch one notch lower than the front wheel latches to improve recycling performance.

WARNING

DO NOT operate without entire Grass Catcher or guard in place. Grass Catcher components are subject to deterioration during normal use. Inspect frequently and replace worn or damaged components immediately.

WARNING

Grass Catcher bags used on SNAPPER products are made of woven fabric, and are subject to deterioration and wear during normal usage. Check condition of bag before each use. Immediately replace worn or damaged catcher bags with only bags recommended by SNAPPER. The grass catcher is optional equipment on some models.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Engine Designation Engine Horse PowerSeries Designation Important Safety Instructions From Previous ColumnFrom Previous Do not refuel the machine indoorsImportant Safety Instructions Table of Contents Introduction Engine Speed ControlNomenclature PRE-START Check List Starting & Operation Engine & BladePropelling Mower Cutting Height AdjustmentHandle Height Adjustment StoppingInstallation of Grass BAG Door Type Bag Recycling Operation Dispose of drain oil properly Service After First 5 Hours 3.2.1. Change Engine OILImportant Drain fuel tank before tipping mower Check Mower Blade Service AnnuallyStorage Procedure Check Engine Drive BeltBlade Sharpening Mower Blade Replacement Standard Blade Wear Limit1.A. Ninja Blade Wear Limit Wheel Drive Control Adjustment Drive Spring Repair/Replacement Driven and Drive Disc ServiceCleaning Drive Disc & Driven Disc Driven Disc AdjustmentOn Next Replacing Rubber Driven Disc Repair & Adjustments Engine Drive Belt Replacement Stretch Type Belts Belt ServiceOn Next Reinstall blade hub and cutter blade Pulley PositionProblem Probable Cause Corrective Action100 Service Performed EachMAINTENANCE/REPLACEMENT Parts USE HRS SeasonDecal Identification CE Compliance Specifications Year Limited Warranty Disclaimer of WarrantyPage Page Page European Steel Deck Walk Mowers Series
Related manuals
Manual 28 pages 62.07 Kb

ERP217019BV specifications

The Snapper ERP217019BV is an advanced and reliable piece of equipment widely recognized in the segment of outdoor power tools, particularly for its efficiency and eco-friendly design. It serves as a mower, ensuring that homeowners and landscaping professionals alike have a high-performing unit at their disposal.

One of the standout features of the Snapper ERP217019BV is its innovative 2-in-1 cutting system. This system allows users to mulch grass clippings or bag them for easier disposal. This versatility not only promotes a healthier lawn by returning nutrients but also offers convenience for users who prefer a tidier yard after mowing. The unit’s 21-inch steel cutting deck provides a wide cutting path, making it ideal for both small and large lawns.

Powering the Snapper ERP217019BV is a robust engine known for its reliability and consistent performance. The OHV engine technology ensures efficient fuel consumption while delivering ample power to tackle tough grass. Its easy-start mechanism adds to user convenience, allowing for quick and hassle-free operation, even at the beginning of mowing sessions.

Another feature that sets the Snapper ERP217019BV apart is its adjustable height settings. This mower offers multiple cutting height options, allowing users to customize the grass length based on their specific lawn needs. The wheel design provides excellent maneuverability, making it easy to navigate through tight spaces, flower beds, and around obstacles.

The Snapper ERP217019BV is designed with user comfort in mind. Its ergonomic handle reduces fatigue during extended use, and the foldable design means that it can be stored easily in smaller spaces. Additionally, it incorporates a simple maintenance protocol, ensuring that the mower remains in top condition with minimal effort.

Equipped with modern technologies like vibration-dampening materials, the Snapper ERP217019BV offers a smooth operation that minimizes user strain and enhances overall mowing experience. Its rugged construction promises durability, making it a long-lasting addition to any outdoor toolkit.

In summary, the Snapper ERP217019BV combines innovative features with user-friendly design, making it a leading choice in the lawn care market. Its powerful performance, adaptability, and comfort make it well-suited for both residential and commercial applications, ensuring every mowing task is completed efficiently and effectively.
Top Page Image Contents