Snapper ERP217019BV Check Mower Blade, Check Engine Drive Belt, Check Transmission POLY-V Belt

Page 12

Section 3 – MAINTENANCE

WARNING

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. Wear heavy leather gloves when handling or working around cutting blades. Blades are extremely sharp and can cause severe injury.

3.2.3. CHECK MOWER BLADE

1.Disconnect spark plug wire and secure end away from plug.

2.Tilt mower up on its rear wheels for access to the blade cap screw. Do not tilt mower with spark plug or carburetor down. See Figure 3.4.

3.Check torque of blade retaining cap screw.

Recommended torque should be 40 ft. lbs.

See

Figure 3.4.

 

4.Check blade for sharpness, wear and damage. Refer to Section “Blade Wear Limits”.

3.2.4.CHECK ENGINE DRIVE BELT

1.Visually check engine drive belt for cracking, fraying, severed or belt strands exposed. If worn or damaged, replace belt before operating mower.

3.2.5. CHECK TRANSMISSION POLY-V BELT

1.Visually check poly-v belt for cracking, fraying, severed or belt strands exposed. If worn or damaged, replace belt before operating mower.

RECOMMENDED

BLADE RETAINING

CAP SCREW

TORQUE VALUE

SHOULD BE 40 FT.

LBS.

FIGURE 3.4

3.3 SERVICE - ANNUALLY

Perform all maintenance as described in the “Service Schedule” section of this manual.

3.3.1. Engine

Service engine according to engine owner’s manual.

3.3.2. Air Filter

Refer to engine owner’s manual for service instructions.

3.3.3. Engine Oil

Refer to engine owner’s manual for service instructions.

3.4 STORAGE PROCEDURE

Refer to the Engine Owner’s Manual for directions regarding engine storage preparations. Prepare the mower for “end of season” storage as follows:

1.Drain fuel from fuel tank and let engine run until all fuel is out of the carburetor.

2.Disconnect and remove the spark plug wire away from spark plug before any other preparations are made!

3.Tape all openings closed to prevent spraying water into exhaust or air intakes during washing.

4.Tilt mower up on its rear wheels and thoroughly clean the underside of the deck. Do not tilt mower with spark plug or carburetor down. Scrape away any accumulation of grass with a putty knife and or wire brush.

5.Lubricate all exposed metal with a light coating of oil to prevent corrosion.

6.On self-propelled models disconnect transfer rod clip and remove ground speed control rod before folding handles.

7.Loosen handle knobs. Carefully fold the handles forward, “flexing” the control cables to prevent cable damage.

8.Store the mower in a shed or other dry area, protected from weather.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Engine Horse Power Engine DesignationSeries Designation Important Safety Instructions From Previous ColumnFrom Previous Do not refuel the machine indoorsImportant Safety Instructions Table of Contents Engine Speed Control IntroductionNomenclature PRE-START Check List Starting & Operation Engine & BladeCutting Height Adjustment Handle Height AdjustmentPropelling Mower StoppingInstallation of Grass BAG Door Type Bag Recycling Operation Service After First 5 Hours 3.2.1. Change Engine OIL Dispose of drain oil properlyImportant Drain fuel tank before tipping mower Service Annually Storage ProcedureCheck Mower Blade Check Engine Drive BeltMower Blade Replacement Standard Blade Wear Limit Blade Sharpening1.A. Ninja Blade Wear Limit Wheel Drive Control Adjustment Driven and Drive Disc Service Cleaning Drive Disc & Driven DiscDrive Spring Repair/Replacement Driven Disc AdjustmentOn Next Replacing Rubber Driven Disc Repair & Adjustments Belt Service Engine Drive Belt Replacement Stretch Type BeltsOn Next Reinstall blade hub and cutter blade Pulley PositionProblem Probable Cause Corrective ActionService Performed Each MAINTENANCE/REPLACEMENT Parts100 USE HRS SeasonDecal Identification CE Compliance Specifications Year Limited Warranty Disclaimer of WarrantyPage Page Page European Steel Deck Walk Mowers Series
Related manuals
Manual 28 pages 62.07 Kb

ERP217019BV specifications

The Snapper ERP217019BV is an advanced and reliable piece of equipment widely recognized in the segment of outdoor power tools, particularly for its efficiency and eco-friendly design. It serves as a mower, ensuring that homeowners and landscaping professionals alike have a high-performing unit at their disposal.

One of the standout features of the Snapper ERP217019BV is its innovative 2-in-1 cutting system. This system allows users to mulch grass clippings or bag them for easier disposal. This versatility not only promotes a healthier lawn by returning nutrients but also offers convenience for users who prefer a tidier yard after mowing. The unit’s 21-inch steel cutting deck provides a wide cutting path, making it ideal for both small and large lawns.

Powering the Snapper ERP217019BV is a robust engine known for its reliability and consistent performance. The OHV engine technology ensures efficient fuel consumption while delivering ample power to tackle tough grass. Its easy-start mechanism adds to user convenience, allowing for quick and hassle-free operation, even at the beginning of mowing sessions.

Another feature that sets the Snapper ERP217019BV apart is its adjustable height settings. This mower offers multiple cutting height options, allowing users to customize the grass length based on their specific lawn needs. The wheel design provides excellent maneuverability, making it easy to navigate through tight spaces, flower beds, and around obstacles.

The Snapper ERP217019BV is designed with user comfort in mind. Its ergonomic handle reduces fatigue during extended use, and the foldable design means that it can be stored easily in smaller spaces. Additionally, it incorporates a simple maintenance protocol, ensuring that the mower remains in top condition with minimal effort.

Equipped with modern technologies like vibration-dampening materials, the Snapper ERP217019BV offers a smooth operation that minimizes user strain and enhances overall mowing experience. Its rugged construction promises durability, making it a long-lasting addition to any outdoor toolkit.

In summary, the Snapper ERP217019BV combines innovative features with user-friendly design, making it a leading choice in the lawn care market. Its powerful performance, adaptability, and comfort make it well-suited for both residential and commercial applications, ensuring every mowing task is completed efficiently and effectively.
Top Page Image Contents