Snapper ERP217019BV important safety instructions Repair & Adjustments

Page 17

Section 4 - REPAIR & ADJUSTMENTS

WARNING

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.

4.3.4.Replacing Rubber Driven Disc (Continued from previous page)

2.Using needle nose pliers, unhook the drive spring and slide the driven disc assembly off the hex shaft. See Figure 4.12.

3.Remove the two snap rings which secure the rubber driven disc to the driven disc assembly. See Figure 4.13.

4.Install new rubber driven disc onto driven disc assembly with retaining rings.

5.Reverse above procedures for reassembly and installation of driven disc assembly.

4.3.5.Replacing Bearing In Driven Disc Assembly IMPORTANT: The bearing on these machines is staked into the thrust plate. The bearing will have to be driven out with a mallet and a large punch. A new bearing with four retaining screws will have to be purchased to replace existing bearing.

If the driven disc bearing requires replacement, remove the driven disc assembly and replace bearing as follows:

1. Remove pin and washer from transfer rod, and remove end of transfer rod from hole in driven disc assembly. See Figure 4.9.

2. Using needle nose pliers, unhook the drive spring and slide the driven disc assembly off the hex shaft. See Figure 4.12.

3. Remove both snap rings that secure rubber driven disc hub to thrust plate. See Figure 4.13.

4. Slide the rubber driven disc hub out of the bearing.

5. Drive out existing bearing.

6. Install new bearing and secure to thrust plate with four retaining screws. Tighten screws securely. 7. Reassemble components in reverse order.

INSTALL NEW

REMOVEDRIVEN DISC

SPRING

REMOVE

SNAP

DRIVEN DISC

ASSEMBLY

RINGS

FIGURE 4.13

FIGURE 4.12

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Series Designation Engine Horse PowerEngine Designation From Previous Column Important Safety InstructionsDo not refuel the machine indoors From PreviousImportant Safety Instructions Table of Contents Nomenclature Engine Speed ControlIntroduction Starting & Operation Engine & Blade PRE-START Check ListHandle Height Adjustment Cutting Height AdjustmentPropelling Mower StoppingInstallation of Grass BAG Door Type Bag Recycling Operation Important Drain fuel tank before tipping mower Service After First 5 Hours 3.2.1. Change Engine OILDispose of drain oil properly Storage Procedure Service AnnuallyCheck Mower Blade Check Engine Drive Belt1.A. Ninja Blade Wear Limit Mower Blade Replacement Standard Blade Wear LimitBlade Sharpening Wheel Drive Control Adjustment Cleaning Drive Disc & Driven Disc Driven and Drive Disc ServiceDrive Spring Repair/Replacement Driven Disc AdjustmentOn Next Replacing Rubber Driven Disc Repair & Adjustments On Next Belt ServiceEngine Drive Belt Replacement Stretch Type Belts Pulley Position Reinstall blade hub and cutter bladeCorrective Action Problem Probable CauseMAINTENANCE/REPLACEMENT Parts Service Performed Each100 USE HRS SeasonDecal Identification CE Compliance Specifications Disclaimer of Warranty Year Limited WarrantyPage Page Page European Steel Deck Walk Mowers Series
Related manuals
Manual 28 pages 62.07 Kb

ERP217019BV specifications

The Snapper ERP217019BV is an advanced and reliable piece of equipment widely recognized in the segment of outdoor power tools, particularly for its efficiency and eco-friendly design. It serves as a mower, ensuring that homeowners and landscaping professionals alike have a high-performing unit at their disposal.

One of the standout features of the Snapper ERP217019BV is its innovative 2-in-1 cutting system. This system allows users to mulch grass clippings or bag them for easier disposal. This versatility not only promotes a healthier lawn by returning nutrients but also offers convenience for users who prefer a tidier yard after mowing. The unit’s 21-inch steel cutting deck provides a wide cutting path, making it ideal for both small and large lawns.

Powering the Snapper ERP217019BV is a robust engine known for its reliability and consistent performance. The OHV engine technology ensures efficient fuel consumption while delivering ample power to tackle tough grass. Its easy-start mechanism adds to user convenience, allowing for quick and hassle-free operation, even at the beginning of mowing sessions.

Another feature that sets the Snapper ERP217019BV apart is its adjustable height settings. This mower offers multiple cutting height options, allowing users to customize the grass length based on their specific lawn needs. The wheel design provides excellent maneuverability, making it easy to navigate through tight spaces, flower beds, and around obstacles.

The Snapper ERP217019BV is designed with user comfort in mind. Its ergonomic handle reduces fatigue during extended use, and the foldable design means that it can be stored easily in smaller spaces. Additionally, it incorporates a simple maintenance protocol, ensuring that the mower remains in top condition with minimal effort.

Equipped with modern technologies like vibration-dampening materials, the Snapper ERP217019BV offers a smooth operation that minimizes user strain and enhances overall mowing experience. Its rugged construction promises durability, making it a long-lasting addition to any outdoor toolkit.

In summary, the Snapper ERP217019BV combines innovative features with user-friendly design, making it a leading choice in the lawn care market. Its powerful performance, adaptability, and comfort make it well-suited for both residential and commercial applications, ensuring every mowing task is completed efficiently and effectively.
Top Page Image Contents