Snapper ERP217019BV important safety instructions Wheel Drive Control Adjustment

Page 14

Section 4 - REPAIR & ADJUSTMENTS

WARNING

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.

4.Sharpen blade on a grinding wheel at an angle of

22to 28 degrees. DO NOT sharpen blade beyond original cutting edge. See Figure 4.4.

DO NOT SHARPEN

 

BEYOND ORIGINAL

 

CUTTING EDGE

22-28º

 

BLADE TIP

END VIEW OF

BLADE ASSEMBLY

ORIGINAL CUTTING EDGE

FIGURE 4.4

5.Check blade for balance. If necessary, correct balance by grinding heavy end of blade.

6.Reinstall blade. See Figure 4.3. Check torque of blade retaining cap screw. Recommended torque should be 40 ft. lbs.

4.2WHEEL DRIVE CONTROL ADJUSTMENT

1.The wheel drive control is properly adjusted when there is 1/16” to 1/8” clearance between the inside of the spring hook and the inside of the clutch cable eye with the wheel drive control released. See Figure 4.5.

CLUTCH CABLE

 

VINYL SPRING

 

1/16” TO 1/8”

CLUTCH CABLE

CLEARANCE

EYE

UPPER

 

SPRING

SPRING HOOK

 

LOWER

 

SPRING

 

CABLE

CLUTCH CABLE EYE

SPRING

FIGURE 4.5

2.To adjust, unhook upper spring from cable eye and rotate spring in direction required to extend or shorten spring length.

3.Rehook upper spring to cable eye and check clearance. Repeat procedure if required.

NOTE: The vinyl spring cover should be kept over the spring at all times except for adjustments.

4.If the wheel drive control fails to return quickly to the “OFF” position when released, check for binding at the cable holdings located on the side of the right handle. The upper clip should be located 2” below the upper knob; the lower clip should be 4” above the lower knob. The cable should slide freely with the clips installed at these locations.

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Series Designation Engine Horse PowerEngine Designation Important Safety Instructions From Previous ColumnFrom Previous Do not refuel the machine indoorsImportant Safety Instructions Table of Contents Nomenclature Engine Speed ControlIntroduction PRE-START Check List Starting & Operation Engine & BladePropelling Mower Cutting Height AdjustmentHandle Height Adjustment StoppingInstallation of Grass BAG Door Type Bag Recycling Operation Important Drain fuel tank before tipping mower Service After First 5 Hours 3.2.1. Change Engine OILDispose of drain oil properly Check Mower Blade Service AnnuallyStorage Procedure Check Engine Drive Belt1.A. Ninja Blade Wear Limit Mower Blade Replacement Standard Blade Wear LimitBlade Sharpening Wheel Drive Control Adjustment Drive Spring Repair/Replacement Driven and Drive Disc ServiceCleaning Drive Disc & Driven Disc Driven Disc AdjustmentOn Next Replacing Rubber Driven Disc Repair & Adjustments On Next Belt ServiceEngine Drive Belt Replacement Stretch Type Belts Reinstall blade hub and cutter blade Pulley PositionProblem Probable Cause Corrective Action100 Service Performed EachMAINTENANCE/REPLACEMENT Parts USE HRS SeasonDecal Identification CE Compliance Specifications Year Limited Warranty Disclaimer of WarrantyPage Page Page European Steel Deck Walk Mowers Series
Related manuals
Manual 28 pages 62.07 Kb

ERP217019BV specifications

The Snapper ERP217019BV is an advanced and reliable piece of equipment widely recognized in the segment of outdoor power tools, particularly for its efficiency and eco-friendly design. It serves as a mower, ensuring that homeowners and landscaping professionals alike have a high-performing unit at their disposal.

One of the standout features of the Snapper ERP217019BV is its innovative 2-in-1 cutting system. This system allows users to mulch grass clippings or bag them for easier disposal. This versatility not only promotes a healthier lawn by returning nutrients but also offers convenience for users who prefer a tidier yard after mowing. The unit’s 21-inch steel cutting deck provides a wide cutting path, making it ideal for both small and large lawns.

Powering the Snapper ERP217019BV is a robust engine known for its reliability and consistent performance. The OHV engine technology ensures efficient fuel consumption while delivering ample power to tackle tough grass. Its easy-start mechanism adds to user convenience, allowing for quick and hassle-free operation, even at the beginning of mowing sessions.

Another feature that sets the Snapper ERP217019BV apart is its adjustable height settings. This mower offers multiple cutting height options, allowing users to customize the grass length based on their specific lawn needs. The wheel design provides excellent maneuverability, making it easy to navigate through tight spaces, flower beds, and around obstacles.

The Snapper ERP217019BV is designed with user comfort in mind. Its ergonomic handle reduces fatigue during extended use, and the foldable design means that it can be stored easily in smaller spaces. Additionally, it incorporates a simple maintenance protocol, ensuring that the mower remains in top condition with minimal effort.

Equipped with modern technologies like vibration-dampening materials, the Snapper ERP217019BV offers a smooth operation that minimizes user strain and enhances overall mowing experience. Its rugged construction promises durability, making it a long-lasting addition to any outdoor toolkit.

In summary, the Snapper ERP217019BV combines innovative features with user-friendly design, making it a leading choice in the lawn care market. Its powerful performance, adaptability, and comfort make it well-suited for both residential and commercial applications, ensuring every mowing task is completed efficiently and effectively.
Top Page Image Contents