Snapper ERP217019BV important safety instructions Problem Probable Cause, Corrective Action

Page 20

TROUBLESHOOTING

PROBLEM

 

PROBABLE CAUSE

Engine Will Not Start

1.

Fuel tank empty.

Using Recoil Starter

2.

Engine needs priming.

 

 

 

 

3.

Spark plug wire disconnected.

Engine Stalls or Stops

1.

Blade control is released or is not being held securely

After Running

 

against handle.

2.Fuel tank empty.

3.Engine air pre-cleaner and or air cleaner dirty.

4.Spark plug defective or gap set improperly.

5.Water, debris or stale fuel in fuel system. Engine Loses Power 1. Engine air pre-cleaner or air cleaner dirty

 

2.

Spark plug faulty.

 

3.

Water, debris or stale fuel in fuel system.

Excessive Vibration 1. Damaged, out of balance or bent mower blade.

 

2.

Loose blade components.

 

3.

Loose or missing air lift (if equipped).

 

4.

Lumpy or frayed belt

Mower Will Not Move

1. Damaged transmission

Loss Of Traction

2. Traction drive belt requires replacement

(Self-Propelled Models)

3. Driven disc slipping

Cutting Grass

1. Cutting height too low or high.

Improperly

2. Engine speed too slow.

 

3.

Forward ground speed too fast.

 

4.

Terraced cut, side to side.

 

5.

Excessive deck pitch, front to rear.

 

6.

Cutting blade dull or damaged.

Poor Grass Discharge

1. Engine speed too slow.

 

2.

Forward speed too fast.

 

3.

Grass is wet.

 

4.

Excessively worn or damaged blade.

 

5.

Build up of grass clippings and debris under deck.

 

6.

Improper blade installed on deck.

 

7.

Blade installed improperly on deck.

Oil Leaking

1. Leaking engine case.

CORRECTIVE ACTION

1.Fill fuel tank with fresh fuel.

2.Prime engine. Check Engine Manual for Instructions.

3.Place spark plug wire onto spark plug.

1.Blade control should be held securely against handle at all times during operation of mower.

2.Fill with fuel to proper level.

3.Clean free of all debris.

4.Service spark plug.

5.Drain and clean fuel system.

1.Clean or replace filters.

2.Service spark plug.

3.Drain and clean fuel system.

1.Service mower blade.

2.Service and tighten loose parts.

3.Replace air lifts. Tighten to proper torque.

4.Replace belt.

1.Contact authorized SNAPPER dealer.

2.Replace traction drive belt.

3.Clean or replace driven disc.

1.Adjust cutting height.

2.Move engine speed control to “FAST” position.

3.Move ground speed control to a slower speed.

4.Adjust height of cut with height adjust levers.

5.Adjust height of cut with height adjust levers.

6.Sharpen cutting edges or replace blade.

1.Move engine speed control to “FAST” position.

2.Move ground speed control to a slower speed.

3.Mow when grass is dry.

4.Service mower blade.

5.Clean deck.

6.Install proper SNAPPER blade.

7.Install blade properly.

1.Contact authorized SNAPPER dealer.

2.Check and tighten drain plug.

3.Make sure dip stick or oil filler cap is securely in place.

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Series Designation Engine Horse PowerEngine Designation Important Safety Instructions From Previous ColumnFrom Previous Do not refuel the machine indoorsImportant Safety Instructions Table of Contents Nomenclature Engine Speed ControlIntroduction PRE-START Check List Starting & Operation Engine & BladeCutting Height Adjustment Handle Height AdjustmentPropelling Mower StoppingInstallation of Grass BAG Door Type Bag Recycling Operation Important Drain fuel tank before tipping mower Service After First 5 Hours 3.2.1. Change Engine OILDispose of drain oil properly Service Annually Storage ProcedureCheck Mower Blade Check Engine Drive Belt1.A. Ninja Blade Wear Limit Mower Blade Replacement Standard Blade Wear LimitBlade Sharpening Wheel Drive Control Adjustment Driven and Drive Disc Service Cleaning Drive Disc & Driven DiscDrive Spring Repair/Replacement Driven Disc AdjustmentOn Next Replacing Rubber Driven Disc Repair & Adjustments On Next Belt ServiceEngine Drive Belt Replacement Stretch Type Belts Reinstall blade hub and cutter blade Pulley PositionProblem Probable Cause Corrective ActionService Performed Each MAINTENANCE/REPLACEMENT Parts100 USE HRS SeasonDecal Identification CE Compliance Specifications Year Limited Warranty Disclaimer of WarrantyPage Page Page European Steel Deck Walk Mowers Series
Related manuals
Manual 28 pages 62.07 Kb

ERP217019BV specifications

The Snapper ERP217019BV is an advanced and reliable piece of equipment widely recognized in the segment of outdoor power tools, particularly for its efficiency and eco-friendly design. It serves as a mower, ensuring that homeowners and landscaping professionals alike have a high-performing unit at their disposal.

One of the standout features of the Snapper ERP217019BV is its innovative 2-in-1 cutting system. This system allows users to mulch grass clippings or bag them for easier disposal. This versatility not only promotes a healthier lawn by returning nutrients but also offers convenience for users who prefer a tidier yard after mowing. The unit’s 21-inch steel cutting deck provides a wide cutting path, making it ideal for both small and large lawns.

Powering the Snapper ERP217019BV is a robust engine known for its reliability and consistent performance. The OHV engine technology ensures efficient fuel consumption while delivering ample power to tackle tough grass. Its easy-start mechanism adds to user convenience, allowing for quick and hassle-free operation, even at the beginning of mowing sessions.

Another feature that sets the Snapper ERP217019BV apart is its adjustable height settings. This mower offers multiple cutting height options, allowing users to customize the grass length based on their specific lawn needs. The wheel design provides excellent maneuverability, making it easy to navigate through tight spaces, flower beds, and around obstacles.

The Snapper ERP217019BV is designed with user comfort in mind. Its ergonomic handle reduces fatigue during extended use, and the foldable design means that it can be stored easily in smaller spaces. Additionally, it incorporates a simple maintenance protocol, ensuring that the mower remains in top condition with minimal effort.

Equipped with modern technologies like vibration-dampening materials, the Snapper ERP217019BV offers a smooth operation that minimizes user strain and enhances overall mowing experience. Its rugged construction promises durability, making it a long-lasting addition to any outdoor toolkit.

In summary, the Snapper ERP217019BV combines innovative features with user-friendly design, making it a leading choice in the lawn care market. Its powerful performance, adaptability, and comfort make it well-suited for both residential and commercial applications, ensuring every mowing task is completed efficiently and effectively.
Top Page Image Contents