Snapper ERP217019BV Mower Blade Replacement Standard Blade Wear Limit, Blade Sharpening

Page 13

Section 4 - REPAIR & ADJUSTMENTS

WARNING

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool. Wear heavy leather gloves when handling or working around cutting blades. Blades are extremely sharp and can cause severe injury.

4.1MOWER BLADE REPLACEMENT

4.1.1. STANDARD BLADE WEAR LIMIT

1.Inspect blade frequently for signs of excessive wear or damage. See Figure 4.1.

NEW BLADE

WEAR LIMIT (NOTCH STARTS)

2.Replace the blade if it is badly chipped, bent, noticeably out of balance or has cracks or notch in either tip. See Figure 4.1 & 4.2. Replace with new blade.

WARNING

DO NOT use a cutting blade that shows signs of excessive wear or damage. Refer to Section “MOWER BLADE REPLACEMENT” for proper blade inspection and service procedures.

4.1.2. BLADE SHARPENING

1.Disconnect spark plug wire and secure end away from plug.

IMPORTANT: Drain fuel tank before tipping mower. DO NOT tip machine with carburetor or spark plug down. Oil from crankcase will saturate the air filter and cause the engine to be hard to start or not start at all. If contamination does occur, the air filter will have to be replaced.

DANGEROUS CONDITION ! DO NOT USE ON MOWER ! REPLACE WITH NEW BLADE.

2.Tilt mower up on its rear wheels. Do not tilt mower with spark plug or carburetor down.

3.Remove blade. See Figure 4.3.

MAKE SURE THAT

BLADE HUB IS

SEATED

BLADE BETWEEN

HUB FLANGES

FIGURE 4.1

4.1.1.A. NINJA BLADE WEAR LIMIT

1.Inspect blade frequently for signs of excessive wear or damage. See Figure 4.2.

NEW BLADE

WEAR LIMIT.

CRACKS OR

 

 

NOTCHES

 

BEGIN TO

 

APPEAR ON TIP

FLANGE

BLADE

CONE WASHER (Concave Side Up)

CAPSCREW

FIGURE 4.3

DANGEROUS !

DO NOT USE A BLADE IN

THIS CONDITION !

FIGURE 4.2

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Engine Designation Engine Horse PowerSeries Designation From Previous Column Important Safety InstructionsDo not refuel the machine indoors From PreviousImportant Safety Instructions Table of Contents Introduction Engine Speed ControlNomenclature Starting & Operation Engine & Blade PRE-START Check ListHandle Height Adjustment Cutting Height AdjustmentPropelling Mower StoppingInstallation of Grass BAG Door Type Bag Recycling Operation Dispose of drain oil properly Service After First 5 Hours 3.2.1. Change Engine OILImportant Drain fuel tank before tipping mower Storage Procedure Service AnnuallyCheck Mower Blade Check Engine Drive BeltBlade Sharpening Mower Blade Replacement Standard Blade Wear Limit1.A. Ninja Blade Wear Limit Wheel Drive Control Adjustment Cleaning Drive Disc & Driven Disc Driven and Drive Disc ServiceDrive Spring Repair/Replacement Driven Disc AdjustmentOn Next Replacing Rubber Driven Disc Repair & Adjustments Engine Drive Belt Replacement Stretch Type Belts Belt ServiceOn Next Pulley Position Reinstall blade hub and cutter bladeCorrective Action Problem Probable CauseMAINTENANCE/REPLACEMENT Parts Service Performed Each100 USE HRS SeasonDecal Identification CE Compliance Specifications Disclaimer of Warranty Year Limited WarrantyPage Page Page European Steel Deck Walk Mowers Series
Related manuals
Manual 28 pages 62.07 Kb

ERP217019BV specifications

The Snapper ERP217019BV is an advanced and reliable piece of equipment widely recognized in the segment of outdoor power tools, particularly for its efficiency and eco-friendly design. It serves as a mower, ensuring that homeowners and landscaping professionals alike have a high-performing unit at their disposal.

One of the standout features of the Snapper ERP217019BV is its innovative 2-in-1 cutting system. This system allows users to mulch grass clippings or bag them for easier disposal. This versatility not only promotes a healthier lawn by returning nutrients but also offers convenience for users who prefer a tidier yard after mowing. The unit’s 21-inch steel cutting deck provides a wide cutting path, making it ideal for both small and large lawns.

Powering the Snapper ERP217019BV is a robust engine known for its reliability and consistent performance. The OHV engine technology ensures efficient fuel consumption while delivering ample power to tackle tough grass. Its easy-start mechanism adds to user convenience, allowing for quick and hassle-free operation, even at the beginning of mowing sessions.

Another feature that sets the Snapper ERP217019BV apart is its adjustable height settings. This mower offers multiple cutting height options, allowing users to customize the grass length based on their specific lawn needs. The wheel design provides excellent maneuverability, making it easy to navigate through tight spaces, flower beds, and around obstacles.

The Snapper ERP217019BV is designed with user comfort in mind. Its ergonomic handle reduces fatigue during extended use, and the foldable design means that it can be stored easily in smaller spaces. Additionally, it incorporates a simple maintenance protocol, ensuring that the mower remains in top condition with minimal effort.

Equipped with modern technologies like vibration-dampening materials, the Snapper ERP217019BV offers a smooth operation that minimizes user strain and enhances overall mowing experience. Its rugged construction promises durability, making it a long-lasting addition to any outdoor toolkit.

In summary, the Snapper ERP217019BV combines innovative features with user-friendly design, making it a leading choice in the lawn care market. Its powerful performance, adaptability, and comfort make it well-suited for both residential and commercial applications, ensuring every mowing task is completed efficiently and effectively.
Top Page Image Contents