Snapper YZ18425BVE, YZ20485BVE Battery Condition Chart, Battery Testing

Page 23

Section 4 - ADJUSTMENTS & REPAIR

WARNING

The electrolyte (acid) produces a highly explosive gas. Keep all sparks, flame and fire away from area when charging battery or when handling electrolyte or battery. Electrolyte (acid) is a highly corrosive liquid. Wear eye protection. Wash affected areas immediately after having eye or skin contact with electrolyte (acid). Battery acid is corrosive. Rinse empty acid containers with water and mutilate before discarding. If acid is spilled on battery, bench, or clothing, etc., Flush with clear water and neutralize with baking soda. DO NOT attempt to charge battery while installed on the SCRAMBLER. DO NOT use “BOOST” chargers on the battery.

IMPORTANT: DO NOT place anything in new battery other than specified electrolyte.

WARNING

DO NOT OVERFILL! DO NOT attempt to charge battery while installed on the SCRAMBLER. DO NOT use “BOOST” chargers on the battery.

5.Slow charge the battery at 1 amp for 2 hours to bring the battery to full charge.

6.After charging, check level of electrolyte and add as needed to bring to proper level.

7.Reinstall cell caps.

8.Install battery into power unit. Connect over flow tube.

9.Connect positive (+) cable (red) first, from wiring harness to the positive terminal (+) on battery using bolt and nut provided in hardware bag. Connect negative (-) cable (black) last, to negative terminal (-) on battery using bolt and nut. Apply a small amount of grease over terminals to prevent corrosion.

Shield the positive terminal with terminal cover located on battery harness. This prevents metal from touching the positive terminal, which could cause sparks.

4.4.6.BATTERY TESTING

There are two types of battery tests: Unloaded and Loaded. The unloaded test is the procedure that will be discussed. It’s the simplest and most commonly used. An unloaded test is made on a battery without discharging current. To perform unloaded testing, check charge condition using either a hydrometer or voltmeter.

1.Using a voltmeter, voltage readings appear instantly to show the state of charge. Remember to hook the positive lead to the battery’s positive terminal, and the negative lead to the negative terminal.

2.A hydrometer measures the specific gravity of each cell. The specific gravity tells the degree of charge; generally, a specific gravity of about 1.265 to 1.280 indicates full charge. A reading of 1.230 to 1.260 indicates the battery should be charged. The Battery Condition chart below shows the charge level as measured by syringe float hydrometer, digital voltmeter and five ball hydrometer.

WARNING

Battery Condition Chart

 

State of Charge

Syringe Hydrometer

Digital Voltmeter

Five Ball Hydrometer

100%

Charged w/ Sulfate Stop

1.280

12.80v

Five Balls Floating

100%

Charged

1.265

12.60v

Four Balls Floating

75% Charged

1.210

12.40v

Three Balls Floating

50% Charged

1.160

12.10v

Two Balls Floating

25% Charged

1.120

11.90v

One Ball Floating

0% Charged

Less than 1.100

Less than 11.80v

Zero Balls Floating

23

Image 23
Contents Model Number Explanation ScramblerPreparation Protection for ChildrenProtection Against Tipovers Operation Safe Handling of GasolineMaintenance Table of Contents Nomenclature IntroductionPRE-START Check List Operating InstructionsOn Next Starting & Operation Engine Electric StartMower Blade Mower Blade StoppingEngine Wheel DriveEngine Must Begin to Stop if Cutting Height AdjustmentEngine Must not Start if Engine should Start ifTwin & Triple Blade Deck Service After First 5 HoursChange Engine OIL Check Mower BladeCheck Transaxle Drive Belt Service Every 25 Operating HoursMower Components Service Every 25 Operating Hours 3.3.1. EngineFront Wheel Bearings Mower Deck Linkage LubricationScrambler Lubrication Storage OUT of Season Service AnnuallyBelt Removal Engine Adjustments & RepairMower Drive Belt Adjustment Belt ReplacementBlade Brake Refer to Section MAINTENANCE/REPLACEMENT PartsHairpin Lift ARM Deck Shown Front or Rear View of DeckTwin Blade Deck Single Blade DeckWheel Brake Adjustment Blade Sharpening Mower Blade Replacement 4.3.1. Blade Wear LimitsBlade Replacement Numbers refer to Section Maintenance /REPLACEMENT PartsBattery Storage Battery Battery RemovalBattery Installation 1. Slide battery into battery cradle Battery ServiceBattery Testing Battery Condition ChartCorrective Action Problem Probable CauseTrouble Shooting on Next Loss Of Traction MAINTENANCE/REPLACEMENT PartsUSE HRS Season Service Performed Each100 Disclaimer of Warranty Year Limited WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Snapper Product Registration Form Scrambler Hydro Drive Series

YZ18425BVE, YZ20485BVE specifications

The Snapper YZ18425BVE and YZ20485BVE represent a significant advancement in outdoor power equipment, specifically designed for those who seek performance, reliability, and efficiency in their lawn care endeavors. These models combine cutting-edge technology and user-friendly features, making them ideal choices for both residential and commercial applications.

At the heart of both models is a robust engine designed to deliver exceptional power. The YZ18425BVE features an 18 horsepower engine, while the YZ20485BVE boasts a more powerful 20 horsepower variant. This substantial power allows for swift and efficient mowing, easily cutting through thick grass and tackling uneven terrains. Both engines are engineered with fuel efficiency in mind, enabling longer operational hours on a single tank and reducing the frequency of refueling.

One of the standout features of the Snapper YZ series is its innovative cutting deck design. With a precise cutting width of 42 inches for the YZ18425BVE and 48 inches for the YZ20485BVE, these mowers provide a clean and consistent cut, ensuring an immaculate lawn. The deck is constructed for durability, featuring advanced materials that withstand the rigors of regular use while maintaining performance.

User comfort and control are paramount in the design of these models. Both mowers come equipped with an ergonomic seat and an intuitive control layout, allowing operators to maneuver with ease and precision. The YZ20485BVE also includes advanced suspension features that enhance the overall riding experience, reducing vibrations and increasing operator comfort during extended use.

In terms of safety, the Snapper YZ series prioritizes user protection. Key safety features include automatic blade shut-off systems and easy-to-reach controls that ensure operators can quickly respond to any situation. Additionally, these models are designed with stability in mind, featuring a wide wheelbase that improves traction and control on various terrains.

Both the YZ18425BVE and YZ20485BVE are equipped with easy maintenance features, such as accessible oil and air filters, allowing users to perform routine checks and servicing without hassle. This commitment to maintenance ease ensures that the mowers remain in peak condition for years of reliable service.

Overall, the Snapper YZ18425BVE and YZ20485BVE are exemplary choices for those looking for high-performance lawn mowers that combine power, efficiency, and user comfort.