Snapper YZ18425BVE, YZ20485BVE MAINTENANCE/REPLACEMENT Parts, Loss Of Traction

Page 25

TROUBLESHOOTING

PROBLEM

 

PROBABLE CAUSE

Rider Will Not Move Or

1. Joystick in the neutral “N” position.

Loss Of Traction

2. Roll release lever is in “ROLL” position.

 

3.

Low transmission hydraulic oil level.

 

4.

Parking Brake engaged.

 

5.

Traction drive belt requires replacement.

Blade(s) Not Cutting

1. Blade engagement switch in the “OFF” position.

 

2.

Clutch belt slipping.

 

3.

Mower belt slipping.

 

4.

Electric clutch not functioning.

Cutting Grass

1. Uneven tire pressure.

Improperly

2. Cutting height too low or high.

 

3.

Engine speed too slow.

 

4.

Forward speed too fast.

 

5.

Terraced cut, side to side.

 

6.

Excessive deck pitch, front to rear.

 

7.

Cutting blade(s) dull or damaged.

 

8.

Blade belt slipping.

 

9.

Check electric clutch.

 

10. Check clutch belt.

Poor Grass Discharge 1. Engine speed too slow.

2.Forward speed too fast.

3.Grass is wet.

4.Excessively worn or damaged blade(s).

5.Build up of grass clippings and debris under deck.

6.Improper blade(s) installed on deck.

7.Blade(s) installed improperly on deck.

Battery Will Not Charge 1. Poor cable connections.

2.Bad battery cell(s).

3.Faulty alternator.

Oil Leaking

1. Leaking hose fittings, clamps or reservoir.

CORRECTIVE ACTION

1.Place joystick in desired speed position.

2.Move roll release lever to the engaged position.

3.Contact authorized SNAPPER dealer.

4.Move parking brake to disengaged position.

5.Replace traction drive belt.

1.Move blade switch to the “ON” position.

2.Replace clutch belt.

3.Replace mower belt.

4.Contact authorized SNAPPER dealer.

1.Bring to proper pressure.

2.Adjust cutting height.

3.Move engine speed control to “FAST” position.

4.Move joystick to a slower speed.

5.Adjust side to side level.

6.Adjust front to rear pitch.

7.Sharpen cutting edges or replace blade(s).

8.Replace blade belt.

9.Adjust to proper specifications. (33” Deck Only)

10.Replace clutch belt.

1.Move engine speed control to “FAST” position.

2.Move joystick to a slower speed.

3.Mow when grass is dry.

4.Service mower blade(s).

5.Clean deck.

6.Install proper SNAPPER blades.

7.Install blades properly.

1.Clean cables and battery terminals.

2.Replace with new battery.

3.Contact engine manufacturer’s dealer.

1.Verify fittings and hose clamps are tight.

4.6. MAINTENANCE/REPLACEMENT PARTS

MAINTENANCE/REPLACEMENT PARTS

42” Cutter Deck Blade (2 Blades Required)

2-6691

48” Cutter Deck Blade (3 Blades Required)

7-5588

42” Cutter Deck Belt (Electric Clutch to Cutting Deck)

7-5235

48” Cutter Deck Belt (Electric Clutch to Cutting Deck)

7-5092

Wheel Drive Belt (Engine to Hydro Transaxle)

4-1823

Mower Drive Belt (Engine to Electric Clutch)

2-9117

Mower Drive Belt (Engine to Electric Clutch) (48” Deck Only)

4-6997

Parts Manual for SCRAMBLER Series 5

06176

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Model Number Explanation ScramblerProtection Against Tipovers Protection for ChildrenPreparation Operation Safe Handling of GasolineMaintenance Table of Contents Nomenclature IntroductionPRE-START Check List Operating InstructionsOn Next Starting & Operation Engine Electric StartEngine Mower Blade StoppingWheel Drive Mower BladeEngine Must not Start if Cutting Height AdjustmentEngine should Start if Engine Must Begin to Stop ifChange Engine OIL Service After First 5 HoursCheck Mower Blade Twin & Triple Blade DeckCheck Transaxle Drive Belt Service Every 25 Operating HoursMower Components Service Every 25 Operating Hours 3.3.1. EngineScrambler Lubrication Mower Deck Linkage LubricationFront Wheel Bearings Storage OUT of Season Service AnnuallyMower Drive Belt Adjustment Engine Adjustments & RepairBelt Replacement Belt RemovalBlade Brake Refer to Section MAINTENANCE/REPLACEMENT PartsHairpin Lift ARM Twin Blade Deck Front or Rear View of DeckSingle Blade Deck Deck ShownWheel Brake Adjustment Blade Replacement Mower Blade Replacement 4.3.1. Blade Wear LimitsNumbers refer to Section Maintenance /REPLACEMENT Parts Blade SharpeningBattery Installation 1. Slide battery into battery cradle Battery Battery RemovalBattery Service Battery StorageBattery Testing Battery Condition ChartTrouble Shooting on Next Problem Probable CauseCorrective Action Loss Of Traction MAINTENANCE/REPLACEMENT Parts100 Service Performed EachUSE HRS Season Disclaimer of Warranty Year Limited WarrantyPrimary Maintenance Primary Maintenance Primary Maintenance Primary Maintenance Snapper Product Registration Form Scrambler Hydro Drive Series

YZ18425BVE, YZ20485BVE specifications

The Snapper YZ18425BVE and YZ20485BVE represent a significant advancement in outdoor power equipment, specifically designed for those who seek performance, reliability, and efficiency in their lawn care endeavors. These models combine cutting-edge technology and user-friendly features, making them ideal choices for both residential and commercial applications.

At the heart of both models is a robust engine designed to deliver exceptional power. The YZ18425BVE features an 18 horsepower engine, while the YZ20485BVE boasts a more powerful 20 horsepower variant. This substantial power allows for swift and efficient mowing, easily cutting through thick grass and tackling uneven terrains. Both engines are engineered with fuel efficiency in mind, enabling longer operational hours on a single tank and reducing the frequency of refueling.

One of the standout features of the Snapper YZ series is its innovative cutting deck design. With a precise cutting width of 42 inches for the YZ18425BVE and 48 inches for the YZ20485BVE, these mowers provide a clean and consistent cut, ensuring an immaculate lawn. The deck is constructed for durability, featuring advanced materials that withstand the rigors of regular use while maintaining performance.

User comfort and control are paramount in the design of these models. Both mowers come equipped with an ergonomic seat and an intuitive control layout, allowing operators to maneuver with ease and precision. The YZ20485BVE also includes advanced suspension features that enhance the overall riding experience, reducing vibrations and increasing operator comfort during extended use.

In terms of safety, the Snapper YZ series prioritizes user protection. Key safety features include automatic blade shut-off systems and easy-to-reach controls that ensure operators can quickly respond to any situation. Additionally, these models are designed with stability in mind, featuring a wide wheelbase that improves traction and control on various terrains.

Both the YZ18425BVE and YZ20485BVE are equipped with easy maintenance features, such as accessible oil and air filters, allowing users to perform routine checks and servicing without hassle. This commitment to maintenance ease ensures that the mowers remain in peak condition for years of reliable service.

Overall, the Snapper YZ18425BVE and YZ20485BVE are exemplary choices for those looking for high-performance lawn mowers that combine power, efficiency, and user comfort.
Top Page Image Contents