Cub Cadet LT1046, LT1050, LT1045 manual Mulching, Inch Decks, inch Decks

Page 16

•For best results it is recommended that the first two laps be cut with the discharge thrown towards the center. After the first two laps, reverse the direction to throw the discharge to the outside for the balance of cutting. This will give a better appearance to the lawn.

•Do not cut the grass too short. Short grass invites weed growth and yellows quickly in dry weather.

•Mowing should always be done with the engine at full throttle.

•Under heavier conditions it may be necessary to go back over the cut area a second time to get a clean cut.

•Do NOT attempt to mow heavy brush and weeds and extremely tall grass. Your tractor is designed to mow lawns, NOT clear brush.

•Keep the blades sharp and replace the blades when worn. Refer to Cutting Blades on page 25 of this manual for proper blade sharpening instructions.

Mulching

Cub Cadet Series 1000 tractors are equipped with a mulch kit which incorporates special blades, already standard on your tractor, in a process of recirculating grass clippings repeatedly beneath the cutting deck. The ultra-fine clippings are then forced back into the lawn where they act as a natural fertilizer. Observe the following points for the best results when mulching.

•Never attempt to mulch if the lawn is damp. Wet grass tends to stick to the underside of the cutting deck preventing proper mulching of the clippings.

•Do NOT attempt to mulch more than 1/3 the total height of the grass or approximately 1-1/2 inches. Doing so will cause the clippings to clump up beneath the deck and not be mulched effectively.

•Maintain a slow ground speed to allow the grass clippings more time to effectively be mulched.

•Always position the throttle control lever in the FAST (rabbit) position and allow it to remain there while mowing. Failing to keep the engine at full throttle places strain on the tractor’s engine and does not allow the blades to properly mulch grass.

NOTE: It is not necessary to remove the discharge chute to operate the mower with the mulch kit installed.

42-inch Decks

On model LT1042, the mulch kit is installed at the factory. To operate the cutting deck without mulching, simply remove the mulch plug by unthreading the plastic wing nut which fastens it to the cutting deck. This will allow the clippings to discharge out the side. See Figure 9.

Carriage Screw

 

Plastic Wing Nut

Mulch Plug

Figure 9

46- and 50-inch Decks

On models LT1045, LT1046 and LT1050, the mulch kit is packed separately within the tractor’s crate. Observe the instructions included with the mulch kit for the best results when mulching.

16

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Operator’s Manual Table of Contents Important Safe Operation Practices General OperationDo not Slope OperationChildren Service TowingPage Slope Gauge —Gas and Oil Fill-up Shipping Brace RemovalKnow Your Lawn Tractor Ignition Switch Module Seat Adjustment LeverChoke Control Brake PedalSystem Indicator Lights Hour Meter234.5 Deck Lift LeverSafety Interlock Switches Reverse Caution ModeTo use the Reverse Caution Mode Operating Your Lawn TractorStarting the Engine Setting the Gauge WheelsStopping the Engine Setting The Cruise Control Engaging the Parking BrakeDriving The Tractor Driving On SlopesUsing the Deck Lift Lever Operating the HeadlightsMoving The Tractor Manually Engaging the PTOInch Decks Mulching50-inch Decks Making Adjustments Leveling the DeckFront To Rear Side to SideSteering Adjustment Parking Brake AdjustmentSeat Adjustment Maintaining Your Lawn Tractor EngineEngine Oil Checking the Oil LevelDraining the Oil Changing the Engine OIlChanging the Oil Filter Precleaner Service Paper ElementAir Filter Re-filling the Crankcase with OilCleaning the Engine And Deck Spark PlugsFuel Filter Smart JetLubrication CarburetorAdjustment Service TiresFuse Cutting BladesBattery Cutting Deck RemovalChanging The Transmission Drive Belt Jump StartingHydrostatic Transmission Changing the Deck BeltAll Models LT1042 Maintenance Chart Troubleshooting Trouble Possible Causes Corrective ActionReplacement Parts LT1042 LT1045 LT1046 LT1050 Attachments & AccessoriesAttachments Specifications MANUFACTURER’S Warranty Coverage CUB Cadet LLC MANUFACTURER’S ONE Year Limited Warranty Commercial USECUB Cadet LLC MANUFACTURER’S Limited Warranty Residential USE

LT1046, LT1050, LT1045 specifications

Cub Cadet is renowned for producing high-quality lawn tractors that cater to both residential and commercial needs. Among their popular models is the Cub Cadet LT series, particularly the LT1045, LT1050, and LT1046, which are designed for optimum performance and user comfort.

The Cub Cadet LT1045 is powered by a robust 19 horsepower Kohler engine, providing ample power for various lawn care tasks. Its hydrostatic transmission offers smooth and effortless maneuverability, allowing users to easily navigate their lawns without the need for gear shifting. Equipped with a 42-inch cutting deck, the LT1045 is ideal for medium-sized yards. Its adjustable cutting height ranges from 1 to 4 inches, giving users flexibility to achieve their desired grass length. Moreover, the LT1045 features a comfortable, ergonomic seat that minimizes fatigue during prolonged use.

Moving up the lineup, the LT1046 comes with a slightly more powerful 21 horsepower engine, suited for larger lawn areas. It also features a 46-inch cutting deck which enhances efficiency by covering more ground in a single pass. The LT1046 has a dual-blade system, improving grass cutting and reducing clumping, which can be beneficial for maintaining a neat appearance. Similar to the LT1045, this model incorporates the same hydrostatic transmission, making it user-friendly.

The Cub Cadet LT1050 is a step above the previous models, with an impressive 23 horsepower engine. This powerful engine is capable of handling tougher terrains and taller grass, making it a perfect choice for larger plots or uneven ground. The LT1050 features a 50-inch cutting deck, which significantly reduces mowing time. Furthermore, it boasts advanced cutting technologies such as SmartJet deck wash and a reinforced cutting deck, ensuring durability and ease of maintenance.

All these models exemplify Cub Cadet's emphasis on comfort and convenience; they are equipped with a high-back seat and easy-to-use controls, catering to users of all experience levels. Some models also include features like LED headlights for early morning or late evening mowing.

In summary, the Cub Cadet LT1045, LT1046, and LT1050 offer a variety of features designed for efficiency, comfort, and durability. With advanced engineering and practical technologies, these models are excellent choices for anyone looking to maintain their lawn with ease and precision.
Top Page Image Contents