Cub Cadet LT1046, LT1050 manual Setting the Gauge Wheels, Starting the Engine, Stopping the Engine

Page 13

Setting the Gauge Wheels

Select the height position of the cutting deck by placing the deck lift lever in any of the six different cutting height notches on the right fender.

Adjust the deck wheels so that they are between ¼-inch and ½-inch above the ground as follows.

WARNING: Keep hands and feet away from the discharge opening of the cutting deck.

Place the tractor on a firm and level surface, preferably pavement, refer to Figure 5, and proceed as follows:

•Place the tractor’s deck lift handle in the normally desired mowing height setting, then check the gauge wheels for contact or excessive clearance with the surface below.

Shoulder Screw

Lock Nut

Shoulder Screw

Lock Nut

Figure 5

•If the wheels contact the surface adjust as follows:

a.Raise the deck lift handle to its highest setting.

b.Remove the rear gauge wheels by removing the lock nuts and shoulder screws which secure them to the deck.

c.Remove the lock nuts and shoulder screws which secure the front gauge wheels to the deck.

d.Place the deck lift handle in the desired mowing height setting.

e.Insert the shoulder screw and flat washer with the rear gauge wheel into the index hole that leaves approximately 1/2" between the bottom of the wheel and the pavement.

f.Note the position of the index hole used; then install the other rear gauge wheel and the front ball wheels into the corresponding index hole of the other gauge wheel brackets.

•If the gauge wheels have excessive clearance with the surface below, lower the wheels to the index

hole that provides the approximate 1/2" clearance as described above.

Refer to Leveling the Deck on page 17 of this manual for more detailed instructions regarding various deck adjustments.

Starting the Engine

WARNING: Do not operate the tractor if the interlock system is malfunctioning. This system was designed for your safety and protection.

NOTE: Refer to the TRACTOR SET-UPon page 8 of this manual for Gasoline and Oil fill-up instructions.

•Insert the tractor key into the ignition switch module.

•Place the PTO (Blade Engage) knob in the disengaged (OFF) position.

•Engage the tractor’s parking brake.

•Activate the choke control.

•Turn the ignition key clockwise to the START position. After the engine starts, release the key. It will return to the NORMAL MOWING position.

IMPORTANT: Do NOT hold the key in the START position for longer than ten seconds at a time. Doing so may cause damage to your engine’s electric starter.

•After the engine starts, deactivate the choke control.

NOTE: Do NOT leave the choke control on while operating the tractor. Doing so will result in a "rich" fuel mixture and cause the engine to run poorly.

Stopping the Engine

WARNING: If you strike a foreign object, stop the engine, disconnect the spark plug wire(s) and ground against the engine. Thoroughly inspect the machine for any damage. Repair the damage before restarting and operating

•If the blades are engaged, place the PTO/Blade Engage knob in the disengaged (OFF) position.

•Place the throttle control near the FAST position

•Turn the ignition key counterclockwise to the STOP position.

•Remove the key from the ignition switch to prevent unintended starting.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Operator’s Manual Table of Contents General Operation Important Safe Operation PracticesDo not Slope OperationChildren Towing ServicePage — Slope GaugeShipping Brace Removal Gas and Oil Fill-upKnow Your Lawn Tractor Seat Adjustment Lever Ignition Switch ModuleChoke Control Brake PedalHour Meter System Indicator Lights234.5 Deck Lift LeverReverse Caution Mode Safety Interlock SwitchesTo use the Reverse Caution Mode Operating Your Lawn TractorStarting the Engine Setting the Gauge WheelsStopping the Engine Engaging the Parking Brake Setting The Cruise ControlDriving The Tractor Driving On SlopesOperating the Headlights Using the Deck Lift LeverMoving The Tractor Manually Engaging the PTOInch Decks Mulching50-inch Decks Leveling the Deck Making AdjustmentsFront To Rear Side to SideSteering Adjustment Parking Brake AdjustmentSeat Adjustment Engine Maintaining Your Lawn TractorEngine Oil Checking the Oil LevelDraining the Oil Changing the Engine OIlChanging the Oil Filter Service Paper Element PrecleanerAir Filter Re-filling the Crankcase with OilSpark Plugs Cleaning the Engine And DeckFuel Filter Smart JetCarburetor LubricationAdjustment Tires ServiceFuse Cutting BladesCutting Deck Removal BatteryChanging The Transmission Drive Belt Jump StartingChanging the Deck Belt Hydrostatic TransmissionAll Models LT1042 Maintenance Chart Trouble Possible Causes Corrective Action TroubleshootingReplacement Parts LT1042 LT1045 LT1046 LT1050 Attachments & AccessoriesAttachments Specifications MANUFACTURER’S Warranty Coverage Commercial USE CUB Cadet LLC MANUFACTURER’S ONE Year Limited WarrantyResidential USE CUB Cadet LLC MANUFACTURER’S Limited Warranty

LT1046, LT1050, LT1045 specifications

Cub Cadet is renowned for producing high-quality lawn tractors that cater to both residential and commercial needs. Among their popular models is the Cub Cadet LT series, particularly the LT1045, LT1050, and LT1046, which are designed for optimum performance and user comfort.

The Cub Cadet LT1045 is powered by a robust 19 horsepower Kohler engine, providing ample power for various lawn care tasks. Its hydrostatic transmission offers smooth and effortless maneuverability, allowing users to easily navigate their lawns without the need for gear shifting. Equipped with a 42-inch cutting deck, the LT1045 is ideal for medium-sized yards. Its adjustable cutting height ranges from 1 to 4 inches, giving users flexibility to achieve their desired grass length. Moreover, the LT1045 features a comfortable, ergonomic seat that minimizes fatigue during prolonged use.

Moving up the lineup, the LT1046 comes with a slightly more powerful 21 horsepower engine, suited for larger lawn areas. It also features a 46-inch cutting deck which enhances efficiency by covering more ground in a single pass. The LT1046 has a dual-blade system, improving grass cutting and reducing clumping, which can be beneficial for maintaining a neat appearance. Similar to the LT1045, this model incorporates the same hydrostatic transmission, making it user-friendly.

The Cub Cadet LT1050 is a step above the previous models, with an impressive 23 horsepower engine. This powerful engine is capable of handling tougher terrains and taller grass, making it a perfect choice for larger plots or uneven ground. The LT1050 features a 50-inch cutting deck, which significantly reduces mowing time. Furthermore, it boasts advanced cutting technologies such as SmartJet deck wash and a reinforced cutting deck, ensuring durability and ease of maintenance.

All these models exemplify Cub Cadet's emphasis on comfort and convenience; they are equipped with a high-back seat and easy-to-use controls, catering to users of all experience levels. Some models also include features like LED headlights for early morning or late evening mowing.

In summary, the Cub Cadet LT1045, LT1046, and LT1050 offer a variety of features designed for efficiency, comfort, and durability. With advanced engineering and practical technologies, these models are excellent choices for anyone looking to maintain their lawn with ease and precision.
Top Page Image Contents