Cub Cadet LT1050, LT1046, LT1045 manual Adjustment

Page 24

•Make sure the fuel tank is filled with clean, fresh gasoline.

•Make sure the fuel tank cap vent is not blocked and that it is operating properly.

•If the fuel tank is equipped with a shut-off valve, make sure it is open.

•Make sure that the in-line fuel filter is clean and unobstructed. Replace the filter if necessary.

•Make sure fuel is reaching the carburetor. Check the fuel lines and fuel pump for restrictions or faulty components, replace as necessary.

•Make sure the air cleaner element is clean and all air cleaner element components are secure.

If, after checking the items listed above, the engine is hard to start, runs roughly, or stalls at low idle speed, it may be necessary to adjust or service the carburetor.

Adjustment

NOTE: Engines may have a fixed idle or limiter cap on the idle fuel adjusting needle. Step 2 can only be performed within the limits allowed by the cap.

1.Start the engine and run at half throttle for five to 10 minutes to warm up. The engine must be warm before performing steps 2 and 3.

2.Low Idle Fuel Needle Setting: Place the throttle into the “idle” or “slow” position. Turn the low idle fuel adjusting needle out (counterclockwise) from the preliminary setting until engine speed decreases (rich). Note the position of the needle. Now turn the adjusting needle in (clockwise). The engine speed may increase, then it will decrease as the needle is turned in (lean). Note the position of the needle. Set the adjusting needle midway between the rich and lean settings. See Figure 20.

Lean

Adjust to Midpoint

Rich

3.Low Idle Speed Setting: Place the throttle control into the “idle” or “slow” position. Set the low idle speed to 1200 RPM* (± 75 RPM) on Models LT1042 & LT1045 (1500 RPM* (± 75 RPM) on Models LT1046 & LT1050) by turning the low idle speed adjusting screw in or out. Check the speed using a tachometer.

NOTE: To ensure best results when setting the low idle fuel needle, the low idle speed must not exceed 1200 RPM (± 75 RPM) on Models LT1042 & LT1045 and 1500 RPM* (± 75 RPM) on Models LT1046 & LT1050).

Figure 20

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Operator’s Manual Table of Contents Important Safe Operation Practices General OperationSlope Operation Do notChildren Service TowingPage Slope Gauge —Gas and Oil Fill-up Shipping Brace RemovalKnow Your Lawn Tractor Ignition Switch Module Seat Adjustment LeverChoke Control Brake PedalSystem Indicator Lights Hour Meter234.5 Deck Lift LeverSafety Interlock Switches Reverse Caution ModeTo use the Reverse Caution Mode Operating Your Lawn TractorSetting the Gauge Wheels Starting the EngineStopping the Engine Setting The Cruise Control Engaging the Parking BrakeDriving The Tractor Driving On SlopesUsing the Deck Lift Lever Operating the HeadlightsMoving The Tractor Manually Engaging the PTOMulching Inch Decks50-inch Decks Making Adjustments Leveling the DeckFront To Rear Side to SideParking Brake Adjustment Steering AdjustmentSeat Adjustment Maintaining Your Lawn Tractor EngineEngine Oil Checking the Oil LevelChanging the Engine OIl Draining the OilChanging the Oil Filter Precleaner Service Paper ElementAir Filter Re-filling the Crankcase with OilCleaning the Engine And Deck Spark PlugsFuel Filter Smart JetLubrication CarburetorAdjustment Service TiresFuse Cutting BladesBattery Cutting Deck RemovalChanging The Transmission Drive Belt Jump StartingHydrostatic Transmission Changing the Deck BeltAll Models LT1042 Maintenance Chart Troubleshooting Trouble Possible Causes Corrective ActionAttachments & Accessories Replacement Parts LT1042 LT1045 LT1046 LT1050Attachments Specifications MANUFACTURER’S Warranty Coverage CUB Cadet LLC MANUFACTURER’S ONE Year Limited Warranty Commercial USECUB Cadet LLC MANUFACTURER’S Limited Warranty Residential USE

LT1046, LT1050, LT1045 specifications

Cub Cadet is renowned for producing high-quality lawn tractors that cater to both residential and commercial needs. Among their popular models is the Cub Cadet LT series, particularly the LT1045, LT1050, and LT1046, which are designed for optimum performance and user comfort.

The Cub Cadet LT1045 is powered by a robust 19 horsepower Kohler engine, providing ample power for various lawn care tasks. Its hydrostatic transmission offers smooth and effortless maneuverability, allowing users to easily navigate their lawns without the need for gear shifting. Equipped with a 42-inch cutting deck, the LT1045 is ideal for medium-sized yards. Its adjustable cutting height ranges from 1 to 4 inches, giving users flexibility to achieve their desired grass length. Moreover, the LT1045 features a comfortable, ergonomic seat that minimizes fatigue during prolonged use.

Moving up the lineup, the LT1046 comes with a slightly more powerful 21 horsepower engine, suited for larger lawn areas. It also features a 46-inch cutting deck which enhances efficiency by covering more ground in a single pass. The LT1046 has a dual-blade system, improving grass cutting and reducing clumping, which can be beneficial for maintaining a neat appearance. Similar to the LT1045, this model incorporates the same hydrostatic transmission, making it user-friendly.

The Cub Cadet LT1050 is a step above the previous models, with an impressive 23 horsepower engine. This powerful engine is capable of handling tougher terrains and taller grass, making it a perfect choice for larger plots or uneven ground. The LT1050 features a 50-inch cutting deck, which significantly reduces mowing time. Furthermore, it boasts advanced cutting technologies such as SmartJet deck wash and a reinforced cutting deck, ensuring durability and ease of maintenance.

All these models exemplify Cub Cadet's emphasis on comfort and convenience; they are equipped with a high-back seat and easy-to-use controls, catering to users of all experience levels. Some models also include features like LED headlights for early morning or late evening mowing.

In summary, the Cub Cadet LT1045, LT1046, and LT1050 offer a variety of features designed for efficiency, comfort, and durability. With advanced engineering and practical technologies, these models are excellent choices for anyone looking to maintain their lawn with ease and precision.
Top Page Image Contents