Cub Cadet LT1050, LT1046, LT1045 Parking Brake Adjustment, Steering Adjustment, Seat Adjustment

Page 18

Parking Brake Adjustment

WARNING: Never attempt to adjust the brakes while the engine is running. Always disengage PTO, stop engine and remove key to prevent unintended starting.

If the tractor does not come to a complete stop when the brake pedal is completely depressed, or if the tractor’s rear wheels can roll with the parking brake applied, the brake is in need of adjustment. The brake disc can be found on the right side of the transmission in the rear of the tractor. Adjust if necessary as follows.

•Looking at the transmission from the right side of the tractor, locate the compression spring and brake disc. See Figure 12.

Brake Rod

Crown Nut

Brake Disc

NOTE: View shown from beneath tractor.

Figure 12

•Carefully remove the cotter pin from the crown nut on the right side of the brake assembly.

•Using a feeler gauge, check the gap between the brake disc and the brake puck. Proper gap is .011".

•Tighten the crown nut until the proper gap is achieved.

•Insert a replacement cotter pin (part # 714-0111) into the crown nut.

Steering Adjustment

If the tractor turns tighter in one direction than the other, or if the ball joints are being replaced due to damage or wear, the steering drag links may need to be adjusted.

Adjust the drag links so that equal lengths are threaded into the ball joint on the left side and the ball joint on the right side:

•Loosen the jam nut found on the drag link at the rear of the ball joint. See Figure 13.

•Remove the hex nut and lock washer on the top of ball joint. See Figure 13.

Hex Nut and

Lock Washer

Pivot Bar

Axle

Jam Nut

Ball Joint

Figure 13

•Thread the ball joint toward the jam nut to shorten the drag link. Thread the ball joint away from the jam nut to lengthen the drag link.

•Replace hex nut and lock washer and retighten the jam nut after proper adjustment is achieved.

NOTE: Threading the ball joints too far onto the drag links will cause the front tires to "toe-in" too far. Proper toe-in is between 1/16" and 5/16".

Front tire toe-in can be measured as follows:

•Place the steering wheel in position for straight ahead travel.

•In front of the axle, measure the distance horizontally from the inside of the left rim to the inside of the right rim. Note the distance.

•Behind the axle, measure the distance horizontally from the inside of the left rim to the inside of the right rim. Note the distance.

•The measurement taken in front of the axle should be between 1/16" and 5/16" less than the measurement taken behind the axle.

•Adjust if necessary.

Seat Adjustment

WARNING: Before operating this machine, make sure the seat is engaged in the seat stop, stand behind the machine and pull back on seat until fully engaged into stop.

To adjust the position of the seat, move the seat adjustment lever (Refer to Figure 1 on Page 9) to the left and slide the seat forward or rearward. Make sure seat is locked into position before operating the tractor.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Operator’s Manual Table of Contents Important Safe Operation Practices General OperationSlope Operation Do notChildren Service TowingPage Slope Gauge —Gas and Oil Fill-up Shipping Brace RemovalKnow Your Lawn Tractor Choke Control Ignition Switch ModuleSeat Adjustment Lever Brake Pedal234.5 System Indicator LightsHour Meter Deck Lift LeverTo use the Reverse Caution Mode Safety Interlock SwitchesReverse Caution Mode Operating Your Lawn TractorSetting the Gauge Wheels Starting the EngineStopping the Engine Driving The Tractor Setting The Cruise ControlEngaging the Parking Brake Driving On SlopesMoving The Tractor Manually Using the Deck Lift LeverOperating the Headlights Engaging the PTOMulching Inch Decks50-inch Decks Front To Rear Making AdjustmentsLeveling the Deck Side to SideParking Brake Adjustment Steering AdjustmentSeat Adjustment Engine Oil Maintaining Your Lawn TractorEngine Checking the Oil LevelChanging the Engine OIl Draining the OilChanging the Oil Filter Air Filter PrecleanerService Paper Element Re-filling the Crankcase with OilFuel Filter Cleaning the Engine And DeckSpark Plugs Smart JetLubrication CarburetorAdjustment Fuse ServiceTires Cutting BladesChanging The Transmission Drive Belt BatteryCutting Deck Removal Jump StartingHydrostatic Transmission Changing the Deck BeltAll Models LT1042 Maintenance Chart Troubleshooting Trouble Possible Causes Corrective ActionAttachments & Accessories Replacement Parts LT1042 LT1045 LT1046 LT1050Attachments Specifications MANUFACTURER’S Warranty Coverage CUB Cadet LLC MANUFACTURER’S ONE Year Limited Warranty Commercial USECUB Cadet LLC MANUFACTURER’S Limited Warranty Residential USE

LT1046, LT1050, LT1045 specifications

Cub Cadet is renowned for producing high-quality lawn tractors that cater to both residential and commercial needs. Among their popular models is the Cub Cadet LT series, particularly the LT1045, LT1050, and LT1046, which are designed for optimum performance and user comfort.

The Cub Cadet LT1045 is powered by a robust 19 horsepower Kohler engine, providing ample power for various lawn care tasks. Its hydrostatic transmission offers smooth and effortless maneuverability, allowing users to easily navigate their lawns without the need for gear shifting. Equipped with a 42-inch cutting deck, the LT1045 is ideal for medium-sized yards. Its adjustable cutting height ranges from 1 to 4 inches, giving users flexibility to achieve their desired grass length. Moreover, the LT1045 features a comfortable, ergonomic seat that minimizes fatigue during prolonged use.

Moving up the lineup, the LT1046 comes with a slightly more powerful 21 horsepower engine, suited for larger lawn areas. It also features a 46-inch cutting deck which enhances efficiency by covering more ground in a single pass. The LT1046 has a dual-blade system, improving grass cutting and reducing clumping, which can be beneficial for maintaining a neat appearance. Similar to the LT1045, this model incorporates the same hydrostatic transmission, making it user-friendly.

The Cub Cadet LT1050 is a step above the previous models, with an impressive 23 horsepower engine. This powerful engine is capable of handling tougher terrains and taller grass, making it a perfect choice for larger plots or uneven ground. The LT1050 features a 50-inch cutting deck, which significantly reduces mowing time. Furthermore, it boasts advanced cutting technologies such as SmartJet deck wash and a reinforced cutting deck, ensuring durability and ease of maintenance.

All these models exemplify Cub Cadet's emphasis on comfort and convenience; they are equipped with a high-back seat and easy-to-use controls, catering to users of all experience levels. Some models also include features like LED headlights for early morning or late evening mowing.

In summary, the Cub Cadet LT1045, LT1046, and LT1050 offer a variety of features designed for efficiency, comfort, and durability. With advanced engineering and practical technologies, these models are excellent choices for anyone looking to maintain their lawn with ease and precision.
Top Page Image Contents