Cub Cadet LT1045, LT1050 manual Making Adjustments, Leveling the Deck, Front To Rear, Side to Side

Page 17

SECTION 6: MAKING ADJUSTMENTS

WARNING: Never attempt to make any adjustments while the engine is running, except where specified in the operator’s manual.

Leveling the Deck

NOTE: Check the tractor’s tire pressure before performing any deck leveling adjustments. Refer to Tires on page 25 for information regarding tire pressure.

Front To Rear

The front of the cutting deck is supported by a stabilizer bar that can adjusted to level the deck from front to rear. The front of the deck should be between 1/4-inch and 3/8-inch lower than the rear of the deck. Adjust if necessary as follows:

•With the tractor parked on a firm, level surface, place the deck lift lever in the top notch (highest position) and rotate the blade nearest the discharge chute so that it is parallel with the tractor.

•Measure the distance from the front of the blade tip to the ground and the rear of the blade tip to the ground.

•The first measurement taken should be between 1/4" and 3/8" less than the second measurement.

•Determine the approximate distance necessary for proper adjustment and proceed, if necessary, to the next step.

•Loosen the two jam nuts on the rear side of the deck stabilizer bracket. See Figure 10

NOTE: Models equipped with a 42-inch deck have only one jam nut, washer and lock nut.

,OOSEN

4IGHTEN

TO LOWER DECK

TO RAISE DECK

Figure 10

•Locate the two lock nuts on the opposite side of the stabilizer bracket. See Figure 10. Tighten the lock nuts to raise the front of the deck; loosen the lock nuts to lower the front of the deck.

•Retighten the two jam nuts loosened earlier when proper adjustment is achieved.

Side to Side

If the cutting deck appears to be mowing unevenly, a side to side adjustment can be performed. Adjust if necessary as follows:

•With the tractor parked on a firm, level surface, place the deck lift lever in the top notch (highest position) and rotate both blades so that they are perpendicular with the tractor.

•Measure the distance from the outside of the left blade tip to the ground and the distance from the outside of the right blade tip to the ground. Both measurements taken should be equal. If they’re not, proceed to the next step.

•Loosen, but do NOT remove, the hex cap screw on the left deck hanger bracket. See Figure 11.

Adjustment Gear

Hex Bolt

Figure 11

•Balance the deck by using a wrench to turn the adjustment gear (found immediately behind the hex cap screw just loosened) clockwise/up or counterclockwise/down.

•The deck is properly balanced when both blade tip measurements taken earlier are equal.

•Retighten the hex cap screw on the left deck hanger bracket when proper adjustment is achieved.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Operator’s Manual Table of Contents General Operation Important Safe Operation PracticesChildren Slope OperationDo not Towing ServicePage — Slope GaugeShipping Brace Removal Gas and Oil Fill-upKnow Your Lawn Tractor Seat Adjustment Lever Ignition Switch ModuleChoke Control Brake PedalHour Meter System Indicator Lights234.5 Deck Lift LeverReverse Caution Mode Safety Interlock SwitchesTo use the Reverse Caution Mode Operating Your Lawn TractorStopping the Engine Setting the Gauge WheelsStarting the Engine Engaging the Parking Brake Setting The Cruise ControlDriving The Tractor Driving On SlopesOperating the Headlights Using the Deck Lift LeverMoving The Tractor Manually Engaging the PTO50-inch Decks MulchingInch Decks Leveling the Deck Making AdjustmentsFront To Rear Side to SideSeat Adjustment Parking Brake AdjustmentSteering Adjustment Engine Maintaining Your Lawn TractorEngine Oil Checking the Oil LevelChanging the Oil Filter Changing the Engine OIlDraining the Oil Service Paper Element PrecleanerAir Filter Re-filling the Crankcase with OilSpark Plugs Cleaning the Engine And DeckFuel Filter Smart JetCarburetor LubricationAdjustment Tires ServiceFuse Cutting BladesCutting Deck Removal BatteryChanging The Transmission Drive Belt Jump StartingChanging the Deck Belt Hydrostatic TransmissionAll Models LT1042 Maintenance Chart Trouble Possible Causes Corrective Action TroubleshootingAttachments Attachments & AccessoriesReplacement Parts LT1042 LT1045 LT1046 LT1050 Specifications MANUFACTURER’S Warranty Coverage Commercial USE CUB Cadet LLC MANUFACTURER’S ONE Year Limited WarrantyResidential USE CUB Cadet LLC MANUFACTURER’S Limited Warranty

LT1046, LT1050, LT1045 specifications

Cub Cadet is renowned for producing high-quality lawn tractors that cater to both residential and commercial needs. Among their popular models is the Cub Cadet LT series, particularly the LT1045, LT1050, and LT1046, which are designed for optimum performance and user comfort.

The Cub Cadet LT1045 is powered by a robust 19 horsepower Kohler engine, providing ample power for various lawn care tasks. Its hydrostatic transmission offers smooth and effortless maneuverability, allowing users to easily navigate their lawns without the need for gear shifting. Equipped with a 42-inch cutting deck, the LT1045 is ideal for medium-sized yards. Its adjustable cutting height ranges from 1 to 4 inches, giving users flexibility to achieve their desired grass length. Moreover, the LT1045 features a comfortable, ergonomic seat that minimizes fatigue during prolonged use.

Moving up the lineup, the LT1046 comes with a slightly more powerful 21 horsepower engine, suited for larger lawn areas. It also features a 46-inch cutting deck which enhances efficiency by covering more ground in a single pass. The LT1046 has a dual-blade system, improving grass cutting and reducing clumping, which can be beneficial for maintaining a neat appearance. Similar to the LT1045, this model incorporates the same hydrostatic transmission, making it user-friendly.

The Cub Cadet LT1050 is a step above the previous models, with an impressive 23 horsepower engine. This powerful engine is capable of handling tougher terrains and taller grass, making it a perfect choice for larger plots or uneven ground. The LT1050 features a 50-inch cutting deck, which significantly reduces mowing time. Furthermore, it boasts advanced cutting technologies such as SmartJet deck wash and a reinforced cutting deck, ensuring durability and ease of maintenance.

All these models exemplify Cub Cadet's emphasis on comfort and convenience; they are equipped with a high-back seat and easy-to-use controls, catering to users of all experience levels. Some models also include features like LED headlights for early morning or late evening mowing.

In summary, the Cub Cadet LT1045, LT1046, and LT1050 offer a variety of features designed for efficiency, comfort, and durability. With advanced engineering and practical technologies, these models are excellent choices for anyone looking to maintain their lawn with ease and precision.
Top Page Image Contents