Craftsman 247.77012 manual Operation, Maintenance & Storage, Do not modify engine

Page 5

SAFETY INSTRUCTIONS

Operation

•Do not put hands and feet near rotating parts or in the feeding chambers and discharge opening. Contact with the rotating impeller can amputate fingers, hands, and feet.

•Before starting the machine, make sure the chipper chute, feed intake, and cutting chamber are empty and free of all debris.

•Thoroughly inspect all material to be shredded and remove any metal, rocks, bottles, cans, or other foreign objects which could cause personal injury or damage to the machine.

•If the impeller strikes a foreign object or if your machine should start making an unusual noise or vibration, immediately shut the engine off. Allow the impeller to come to a complete stop. Disconnect the spark plug wire, ground it against the engine and perform the following steps:

1.Inspect for damage.

2.Repair or replace any damaged parts.

3.Check for any loose parts and tighten to assure continued safe operation.

•Do not allow an accumulation of processed material to build up in the discharge area. This can prevent proper discharge and result in kickback of material through the feed opening.

•Do not attempt to shred or chip material larger than specified on the machine or in this manual. Personal injury or machine damage could result.

•Never attempt to unclog either the feed intake or discharge opening while the engine is running. Shut the engine off, wait until all moving parts have stopped, disconnect the spark plug wire and ground it against the engine before clearing debris.

•Never operate without vacuum bag and discharge chute properly attached to the machine. Never empty or change vacuum bag while the engine is running. Zippered end of vacuum bag must be kept closed at all times during operation.

•Never operate without either the inlet nozzle or optional hose attachment properly attached to the machine. Never attempt to attach or change either attachment while the engine is running.

•Keep all guards, deflectors and safety devices in place and operating properly.

•Keep your face and body back and to the side of the chipper chute while feeding material into the machine to avoid accidental kickback injuries.

•Never operate this machine without good visibility or light. Always be sure of your footing and keep a firm hold on the handles.

•Do not operate this machine on a gravel surface.

•Do not operate this machine while under the influence of alcohol or drugs.

•Muffler and engine become hot and can cause a burn. Do not touch.

•Never pick up or carry machine while the engine is running.

Maintenance & Storage

•Never tamper with safety devices. Check their proper operation regularly.

•Check bolts and screws for proper tightness at frequent intervals to keep the machine in safe working condition. Also, visually inspect machine for any damage and repair, if needed.

•Before cleaning, repairing, or inspecting, stop the engine and make certain the impeller and all moving parts have stopped. Disconnect the spark plug wire and ground it against the engine to prevent unintended starting.

•Do not change the engine governor settings or overspeed the engine. The governor controls the maximum safe operating speed of the engine.

•Maintain or replace safety and instruction labels, as necessary.

•Follow this manual for safe loading, unloading, transporting, and storage of this machine.

•Never store the machine or fuel container inside where there is an open flame, spark or pilot light such as a water heater, furnace, clothes dryer, etc.

•Always refer to the operator’s manual for proper instructions on off-season storage.

•If the fuel tank has to be drained, do this outdoors.

•Observe proper disposal laws and regulations for gas, oil, etc. to protect the environment.

Do not modify engine

To avoid serious injury or death, do not modify engine in any way. Tampering with the governor setting can lead to a runaway engine and cause it to operate at unsafe speeds. Never tamper with factory setting of engine governor.



Page 4 Page 6
Image 5
Page 4 Page 6
Contents Operator’s Manual Warranty Table of ContentsProduct Specifications Model NumberRepair Protection Agreement Preparation Safety InstructionsTraining Do not modify engine Maintenance & StorageOperation This page left intentionally blank To Avoid Serious Injury Safety LabelsOpening Carton AssemblyRemoving Unit from Carton Loose Parts in CartonAttaching the Handle Snap bag clip to the top of the lower handle Attaching the BAGAttaching the Blower Chute Nozzle Height AdjustmentLocking rod to secure chute in place, as in Figure SectionOperation Choke Control Throttle ControlStarter Handle GAS and OIL FILL-UPTion when operating the Yard Vacuum Attach spark plug wire and rubber boot to spark plugTo Start Engine To Stop EngineTo Remove Blower Chute To Empty BAGEngine Maintenance Service and MaintenanceServicing the Air Cleaner General RecommendationsLubrication Clean EquipmentRemoving the Flail Screen Sharpening or Replacing Chipper Blade Disconnect and ground the spark plug wire to retaining postService and Maintenance Each Use Engine oil level Check Maintenance ScheduleGas in the tank † Under heavy load or in high temperatures Preparing the yard vacuum OFF-SEASON StoragePreparing the Engine Troubleshooting Yard Vacuum Model No Parts ListDescription 121 11A 24 23 781-04068 Upper Housing Blower Chute AssemblyHeight Adjustment Bearing Pivot Arm AssemblyCraftsman 6.5 H.P. Engine Model No T02 For Yard Vacuum Model  1  engine gaSkeT SeT Kit-Bushing/Seal Cylinder Assembly299819S† Seal-Oil Magneto Side Sump-Engine66538S Boot-Spark Plug 692310 Switch-Stop690662 281505496116 Base-Air Cleaner Primer 692017 Assembly-Dipstick/Tube692298 Cover-Air Cleaner 691669 Screw Air Cleaner Primer BracketOwner’s Warranty Responsibilities Sears Emission Control Defects Warranty CoverageSears Emission Control Defects Warranty Provisions This page applicable in the U.S.A. and Canada onlyPage Garantía ÍndiceEspecificaciones DEL Producto Número DE ModeloAcuerdo DE Protección Para Reparaciones Preparativos Instrucciones DE SeguridadCapacitación No modifique el motor OperaciónMantenimiento y almacenamiento Apertura DE LA Caja DE Cartón MontajeCómo Sacar LA Unidad DE LA Caja Piezas Sueltas Dentro DE LA CajaFigura Montaje DE LA ManijaMontaje DE LA Bolsa Ajuste DE LA Altura DEL Pico Instalar EL Canal DE SopladoCuando deslice la varilla de seguridad. Vea la figura En la siguiente secciónOperación Control de obturación Control del estranguladorManija del arrancador Llenado DE Gasolina Y AceitePara Detener EL Motor Para Encender EL MotorConecte el cable de la bujía y la manga de goma a la misma Mantenga Siempre el control del estrangulador en posiciónCortadora Descarga DE LA BolsaExtracción DEL Canal DE Soplado Recomendaciones Generales MantenimientoMantenimiento de Motor Servicio a La BujíaLimpieza DEL Equipo LubricaciónExtracción DE LA Pantalla DE DES Granado Retire el montaje de la bolsa o el canal de soplado Afilado O Reemplazo DE LAS Hojas DE LA CortadoraPico de plástico negro Tornillos con reborde Tanque † Bajo carga pesada o en temperaturas altas Lista DE MantenimientoCada Uso Nivel del aceite de motor Comprobar Preparación del Motor Almacenamiento Fuera DE TemporadaLa preparación del vacío de yarda Ya que los motores almacenaron más de 30 díasSolución DE Problemas Flujo de aire restringido El motor recalienta El nivel de aceite del motor es bajoMotor y alojamiento de soplador Quite la bujía y ajuste el huecoPiezas con garantía Esta página se aplica sólo en EE.UU. y CanadáMotor certificado Notas Get it fixed, at your home or ours

247.77012 specifications

The Craftsman 247.77012 is a versatile and powerful lawn tractor designed for homeowners seeking efficiency and ease of use in yard maintenance. Known for its robust construction and reliable performance, this model is particularly favored for its user-friendly features and advanced technology.

At the heart of the Craftsman 247.77012 is its durable 19-horsepower engine, providing ample power to tackle various terrain and grass types. This engine is equipped with a hydrostatic transmission, allowing for seamless speed adjustments without the need for gear shifting. This feature enhances maneuverability, making it easy to navigate around obstacles like trees and flower beds.

One of the standout characteristics of the 247.77012 is its cutting deck. Designed for a clean and precise cut, the 42-inch reinforced steel deck is equipped with mulching capabilities, enabling grass clippings to be recycled back into the lawn as natural fertilizer. This not only promotes healthier grass growth but also reduces the need for bagging and disposal.

The lawn tractor boasts a comfortable seating experience, featuring an adjustable high-back seat that offers excellent lumbar support. This ergonomic design ensures that users can operate the tractor for extended periods without discomfort. Additionally, the easy-to-read dashboard displays essential information such as fuel levels and engine status, enhancing the overall user experience.

In terms of technology, the Craftsman 247.77012 incorporates several innovative solutions to improve functionality. The tractor is compatible with optional attachments, including baggers and snow blades, transforming it into a year-round landscaping tool. This adaptability adds a great deal of value for those looking to extend the utility of their equipment.

Ease of maintenance is another vital feature of the Craftsman 247.77012. The model includes a built-in washout port, allowing for quick and hassle-free cleaning of the cutting deck after mowing. Routine maintenance tasks are made more accessible, ensuring that the lawn tractor remains in top condition and prolongs its lifespan.

Overall, the Craftsman 247.77012 is a reliable and efficient lawn care solution, merging power, comfort, and versatility to meet the needs of homeowners. With its blend of traditional craftsmanship and modern advancements, this lawn tractor stands out as a commendable choice for anyone looking to maintain their yard effortlessly.
Top Page Image Contents