Safety Features, Dispositifs DE Sécurité | Husky 1650 PSL specification

2.0 SAFETY FEATURES

The pressure washer is equipped with a stop device which will sense when the trigger on the gun is released. It will open the power circuit to the motor and cause the pressure washer to stop.

WARNING: The pressure washer is also equipped with a main power ON/ OFF switch located on the unit. It should

always be moved to the off position WARNING when the pressure washer is not being used to prevent possible injury or

damage.

MOTOR OVERLOAD

The electric motor in this pressure washer is equipped with an overload protection device which will automatically shut off the motor in the event the motor draws excessive current or overheats.

The device will automatically reset itself and resume normal operation after a short period of time.

EXTENSION CORDS

WARNING: Extension cords are not recommended unless they are plugged into a ground-fault circuit-interrupter

WARNING found in circuit boxes or protected receptacles.

Use only 3-wire extension cords that have 3-prong grounding-type plugs and 3-pole cord connectors that accept the plug from the product.

Use only extension cords that are intended for outdoor use. These extension cords are identified by a marking “Acceptable for use with outdoor appliances; store indoors while not in use”.

Use only extension cords having an electrical rating higher than the rating of the product.

Do not use damaged extension cords.

Examine extension cord before using and replace if damaged.

Do not abuse extension cord and do not yank on any cord to disconnect.

Keep cord away from heat and sharp edges.

Always disconnect the extension cord from the receptacle before disconnecting the product from the extension cord.

2.0 DISPOSITIFS DE SÉCURITÉ

Le nettoyeur à pression est muni d'un dispositif d'arrêt qui coupe automatiquement le circuit électrique lorsque la gâchette est relâchée. L'appareil s'arrête aussitôt.

ATTENTION : Le nettoyeur à pression est également muni d’un interrupteur électrique principal MARCHE/ARRÊT.

Lorsque le nettoyeur n’est pas utilisé, il ATTENTION faut que l’interrupteur soit toujours en position ARRÊT afin d’éviter blessures

ou des dommages à l’appareil.

SURCHARGE DU MOTEUR

Le moteur électrique du nettoyeur à pression est muni d’un dispositif de protection de surcharge qui bloque automatiquement le moteur en cas de surcharge de courant ou de surchauffe.

Le dispositif se réarme automatiquement et rétablit les conditions normales de fonctionnement dans un bref délai.

RALLONGES

ATTENTION: L'usage de rallonges est déconseillé, à moins qu’ils ne soient branchés à un disjoncteur de fuite à la

ATTENTION terre situé dans des boîtiers électriques

ou des réceptacles protégés.

Utilisez seulement des rallonges à 3 fils avec des prises de mise à la terre à 3 broches et des connecteurs à 3 pôles compatibles avec la fiche du produit.

Utiliser exclusivement des rallonges pouvant être utilisées à l’extérieur. Ces rallonges sont marquées “Adaptées à un usage à l’extérieur : mettre à l’abri en cas de non-utilisation”.

Utiliser seulement des rallonges d’une puissance électrique non inférieure à la puissance nominale de l’appareil.

Ne pas utiliser de rallonges endommagées. Avant utilisation, vérifier la rallonge et la remplacer si elle est endommagée.

Ne pas utiliser de manière incorrecte et ne pas secouer pour débrancher. Tenir les rallonges éloignées des sources de chaleur et d’arêtes vives.

Avant de débrancher l’appareil de la rallonge, débrancher celle-ci de la prise.

1650 PSL specifications

The Husky 1650 PSL is a sophisticated and versatile injection molding machine specifically designed for high-performance applications across various industries. Renowned for its reliability and efficiency, the Husky 1650 PSL stands out as an optimized solution for companies requiring precision in their production lines.

One of the most notable features of the Husky 1650 PSL is its high-speed injection capabilities. This machine utilizes advanced hydraulics to deliver rapid injection cycles, resulting in shorter production times and enhanced productivity. The machine boasts a robust clamping force of 1650 tons, providing the necessary support for processing larger and more complex molds with precision.

In terms of technology, the Husky 1650 PSL incorporates a user-friendly, programmable control system that allows for real-time monitoring and adjustments. This feature makes it easy for operators to optimize the molding process based on specific requirements. Additionally, the machine is equipped with state-of-the-art servo technology, which significantly improves energy efficiency while reducing cycle times. This not only leads to lower operational costs but also enhances overall sustainability.

The machine's design includes a wide range of customizable options, allowing manufacturers to tailor the Husky 1650 PSL to their specific needs. The modular design supports integration with various auxiliary equipment, such as robots and conveyors, fostering a streamlined manufacturing process. Moreover, the machine's advanced cooling and heating systems ensure consistent temperatures for stable material processing, directly contributing to the quality of the final products.

Another standout feature of the Husky 1650 PSL is its compatibility with a variety of thermoplastic materials, making it an ideal choice for producing complex parts in industries ranging from automotive to consumer goods. The machine's versatility is further enhanced by its ability to work with multiple cavity molds, contributing to higher output while maintaining tight tolerances.

In conclusion, the Husky 1650 PSL is a powerful injection molding machine that combines high performance, advanced technology, and customization capabilities to meet the rigorous demands of modern manufacturing. Its innovative features not only improve production efficiency but also ensure the consistent quality of molded products, making it a valuable asset in any production facility.