Husky 1650 PSL warranty Power Supply Connection, Branchement DE L‘ALIMENTATION Électrique

Page 14

3. .3 POWER SUPPLY CONNECTION

The pressure washer is factory-equipped with an electrical cord. This cord should only be connected to an electrical outlet installed in accordance with local safety regulations.

NOTE: the power supply must be 120v, 60hz and a minimum 15 amp circuit.

WARNING

A. Connect only to properly grounded outlet. Do not remove grounding pin.

B. Inspect cord before using. Do not use if cord is damaged.

C. Keep all connections dry and off the ground. D. Do not touch plug with wet hands.

E. If replacement of the plug or cord is needed, use only identical replacement parts. Contact Customer Service for proper replacement parts.

Extension cords are not recommended unless they are plugged into a receptacle protected by a ground fault circuit interrupter. Any extension cord used should be 14 AWG and no longer than 50 feet to prevent excessive voltage loss. Use only extension cords intended for outdoor use. These extension cords are identified by a marking “Acceptable for use with outdoor appliances; store indoors when not in use”.

3.3BRANCHEMENT DE L‘ALIMENTATION ÉLECTRIQUE

Le nettoyeur à pression est muni d’un câble électrique. Ce câble devra être relié uniquement à une prise électrique conforme à la réglementation locale de sécurité.

REMARQUE : Le courant électrique devra être de 120V, 60Hz avec un circuit d’au moins 15 A.

ATTENTION

A. Branchez seulement à une prise avec mise à la terre.

B. Vérifiez le câble avant l’utilisation. S’il est endommagé, ne pas l’utiliser.

C. Gardez tous les raccordements au sec et éviter de les poser par terre.

D. Ne touchez pas la prise avec les mains mouillées.

E. S’il est nécessaire de remplacer la fiche ou la prise, utilisez uniquement des pièces de rechange du même type. Communiquez avec le service à la clientèle pour tout renseignement sur le remplacement des pièces.

L’utilisation de rallonges est déconseillée, à moins qu’ils ne soient branchés dans un réceptacle protégé par un disjoncteur de fuite à la terre. Tout cordon de rallonge utilisé doit être du type 14 AWG et d’une longueur inférieure à 15 m pour empêcher une perte de tension excessive. N’utilisez que des rallonges conçues pour utilisation à l’extérieur. Celles-ci sont identifiées par une étiquette « Conçu pour une utilisation avec des appareils d’extérieur; conserver à l’intérieur lorsque non utilisé ».

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents OPERATOR’S Manual Manuel DE L’OPÉRATEUR Huskypowerwasher Serial NumberEnregistrez votre numéro de série ci-dessous Simple Remove the Water PlugConnect to Water Supply Branchez AU RobinetTurn on Water Supply Index ’appareil Safety and Operation RulesConsignes D‘UTILISATION ET DE Sécurité 11. Éloigner toute personne de la zone de travail Grounding Instructions Instructions DE Mise À LA TerrePièces Parts ListParts Drawing Ou des réceptacles protégés Safety FeaturesDispositifs DE Sécurité Tuyau À Haute Pression InstallationHigh Pressure Hose Water Connection Branchement D‘EAUPower Supply Connection Branchement DE L‘ALIMENTATION ÉlectriqueOperating Instructions Mode DemploiSTART-UP Procedure Mise EN MarcheHigh PRESSURE/LOW Pressure see the picture in the next High PRESSURE/TURBO Spray Adjustable Spray NozzleLance Avec Tête Réglable Haute PRESSION/LANCE TurboUSE of Cleaning Chemicals Utilisation DE Détergents Techniques DE NettoyageEND of Operation Application of Soap DegreaserApplication of Liquid Vehicle WAX Application DE Savon DégraissantMaintenance EntretienCooling System LubricationWater Screen LubrificationAfter Extended Storage LE Déplacement ET LE RemisageMoving and Storage Instructions Après UN Entreposage ProlongéTo access the motor proceed as follows Switch on machine with spray gun open Install coverInstallez le couvercle Insert a suitable hexagon socket wrench size‘‘žÞÌΞÌXžž‘Ì@šbÌÂkÅÎ@ÂÎÌךŠÎ TroubleshootingŠÅXžšškXÎÌ@‘‘̞·kÂÌ‘ž@bÅÌžšÌ·k 3ÅkÌ-ž-kÂÌkßÎkšÅŠžšÌXžÂbÌ@ŬûNäökŒÃbkÃbl¬ä›@ŒäûöŒûöÃbkìlë@kÃbkÃëökÃxûöXŒäûöök ÄXëk ÏïÃäöbälÃFKŒÃxk¬ïl Ã13 InformationDonnées Techniques Technical DataFonctionnement, notre service à la clientèle est là Pression de la pompe Psi MAXLimited Warranty HOW to Obtain Warranty Page Paces Ferry RD. N. W ATLANTA, Georgia

1650 PSL specifications

The Husky 1650 PSL is a sophisticated and versatile injection molding machine specifically designed for high-performance applications across various industries. Renowned for its reliability and efficiency, the Husky 1650 PSL stands out as an optimized solution for companies requiring precision in their production lines.

One of the most notable features of the Husky 1650 PSL is its high-speed injection capabilities. This machine utilizes advanced hydraulics to deliver rapid injection cycles, resulting in shorter production times and enhanced productivity. The machine boasts a robust clamping force of 1650 tons, providing the necessary support for processing larger and more complex molds with precision.

In terms of technology, the Husky 1650 PSL incorporates a user-friendly, programmable control system that allows for real-time monitoring and adjustments. This feature makes it easy for operators to optimize the molding process based on specific requirements. Additionally, the machine is equipped with state-of-the-art servo technology, which significantly improves energy efficiency while reducing cycle times. This not only leads to lower operational costs but also enhances overall sustainability.

The machine's design includes a wide range of customizable options, allowing manufacturers to tailor the Husky 1650 PSL to their specific needs. The modular design supports integration with various auxiliary equipment, such as robots and conveyors, fostering a streamlined manufacturing process. Moreover, the machine's advanced cooling and heating systems ensure consistent temperatures for stable material processing, directly contributing to the quality of the final products.

Another standout feature of the Husky 1650 PSL is its compatibility with a variety of thermoplastic materials, making it an ideal choice for producing complex parts in industries ranging from automotive to consumer goods. The machine's versatility is further enhanced by its ability to work with multiple cavity molds, contributing to higher output while maintaining tight tolerances.

In conclusion, the Husky 1650 PSL is a powerful injection molding machine that combines high performance, advanced technology, and customization capabilities to meet the rigorous demands of modern manufacturing. Its innovative features not only improve production efficiency but also ensure the consistent quality of molded products, making it a valuable asset in any production facility.
Top Page Image Contents