Husky 1750 US manual Power Supply Connection, Service for proper replacement parts

Page 14

3.3POWER SUPPLY CONNECTION

The pressure washer is factory-equipped with an

electrical cord and a Ground Fault Circuit Interrupter

(GFCI) power plug.

This cord should only be connected to an electrical

outlet installed in accordance with local safety

regulations.

NOTE: the power supply must be 120v, 60hz and a

minimum 15 amp circuit. (Dedicated)

WARNING: test GFCI before each use.

DO NOT use pressure washer if test below

fails.

GFCI Test Procedures:

1.Plug GFCI into power receptacle. Indicator should

turn red.

2.Press test button. Red indicator should disappear.

3.Press reset button for use.

Do not use if above test fails.

NOTE: the GFCI must be reset each time the pressure

washer is connected to an electrical outlet. Reset by simply

pushing the reset button on the GFCI power plug.

WARNING

A.Connect only to properly grounded outlet. Do not

remove grounding pin.

B.Inspect cord before using. Do not use if cord is

damaged.

C.Keep all connections dry and off the ground.

D.Do not touch plug with wet hands.

E.The pressure washer is provided with a ground-

fault circuit interrupter built into the power plug. If

replacement of the plug or cord is needed, use

only identical replacement parts. Contact Customer

Service for proper replacement parts.

Extension cords are not recommended unless they are

plugged into a receptacle protected by a ground fault

circuit interrupter. Any extension cord used must be

12 AWG outdoor with maximum length of 25 feet to

prevent excessive voltage loss.

Use only extension cords intended for outdoor use.

These extension cords are identified by a marking

“Acceptable for use with outdoor appliances; store

indoors when not in use”.

3.3CONEXIÓN CON LA POTENCIA DE

ALIMENTACIÓN

La máquina de lavar a presión está dotada de fábrica

de un cable eléctrico y de un enchufe de

alimentación con interruptor de circuito con toma

de tierra (GFCI).

El cable deberá ser conectado únicamente a una toma

corriente eléctrica instalada en conformidad con las

normativas locales de seguridad.

NOTA: la corriente eléctrica deberá ser de

120V, 60 Hz con un circuito de por lo menos

15 amperios . (Dedicado) .

ATENCIÓN: controlen el interruptor de cir-

cuito con toma de tierra (GFCI) antes del uso.

No utilicen la máquina de lavar a presión si el

control efectuado da un resultado negativo.

Procedimientos de prueba del GFCI:

1.Conecte el GFCI en la tomacorriente. El indicador

debe ponerse en rojo.

2.Presionar el botón de prueba (test). El indicador

rojo debería desaparecer.

3.Presione el botón de reinicio (reset) para utilizar el

equipo. No lo utilice si la prueba falla..

No usar si la prueba descrita anteriormente falla

NOTA: el GFCI debe reiniciarse todas las veces que

se conecta la hidrolimpiadora a una toma eléctrica.

ATENCIÓN

A.Conecte el equipo sólo a una tomacorriente con toma

a tierra adecuada. No retire la clavija de toma a tierra

B.Revise el cable antes del uso. Si está dañado, no lo

utilice.

C.Mantenga secas y fuera de tierra todas las

conexiones

D.No toque el enchufe con las manos mojadas

E.La máquina de lavar a presión es suministrada con

un interruptor de circuito con toma de tierra instalado

en el enchufe de alimentación. Si es necesario

substituir el enchufe o el cable, usen sólo piezas de

repuesto del mismo tipo. Para una substitución

correcta, contacte al Servicio al Cliente.

No se aconseja el uso de extensiones si no están

introducidas en una tomacorriente protegida por el

interruptor de circuito con toma de tierra. Cualquier

extensión utilizada debe ser del tipo 12 AWG fuera y

la longitud no debe superar los 25 pies con el fin de

prevenir una excesiva dispersión de voltaje. Utilice sólo

extensiones para uso exterior. Tales extensiones están

señaladas con la siguiente frase: “Adecuadas para uso

exterior; almacenar en lugar cerrado cuando no es

utilizada.”

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Page Huskypowerwasher Serial NumberImportante Número de SeriePage Page Page Solución DE Problemas InstallationWater Connection Power Supply Operating Instructions High PressureSafety and Operation Rules Normas Operativas Y DE SeguridadWasher to maintain complete control of the wand Wear safety goggles while operatingNot recommended for use on painted surfaces Durante el uso, no cubra la máquina de lavar aInstrucciones Para LA Toma DE Tierra Grounding InstructionsOr breakdown, grounding provides a path of least Page Extensiones Extension Cords Safety Features Características Relativas LA SeguridadMotor Overload Sobrecarga DEL Motor Page Conexión CON LA Potencia DE Alimentación Power Supply ConnectionService for proper replacement parts Page Page Page Page Page END of Operation MaintenanceMantenimiento Cooling System Sistema DE Refrigeración LOS DañosPage Page Troubleshooting Problem Possible Cause CorrectionPage Problemas Causas Probables Solución Localización DE LAS AveríasPage Replacement Parts Accessories Piezas DE Repuesto Y AccesoriosDatos Técnicos Technical DataSee OUR WEB Site for Replacement Or Missing Parts Exclusiones DE LA Cobertura EN Cómo Obtener LA Garantía Fault circuit interrupter Gfci effective from the dateHOW to Obtain Warranty Made in Italy Hecho EN Italy

1750 US specifications

The Husky 1750 US is an innovative and versatile injection molding machine designed to meet diverse manufacturing needs in the plastics industry. This machine stands out due to its blend of sophisticated technology, exceptional performance, and user-friendly features, making it an ideal choice for both small-scale and large-scale production processes.

One of the main features of the Husky 1750 US is its robust and efficient hydraulic system. This system is engineered to provide precise control over the injection process, ensuring consistent quality in each molded part. The machine's clamping unit boasts a high injection speed and rapid cycle times, enabling manufacturers to optimize their productivity. With a clamping force of 1750 tons, it caters well to a wide variety of applications, including packaging, automotive components, and medical devices.

The Husky 1750 US is equipped with cutting-edge technologies that enhance its performance. Its smart processing capabilities allow operators to monitor and adjust key parameters in real time, leading to reduced cycle times and improved energy efficiency. The machine features an advanced control system that provides intuitive user interfaces, making setup and operation effortless even for those with minimal experience.

Another key characteristic of the Husky 1750 US is its versatility. It is compatible with a wide range of molds and materials, including high-performance thermoplastics, allowing it to adapt to the needs of different production environments. This flexibility is further amplified by its modular design, enabling easy upgrades and customization to meet evolving operational demands.

In terms of maintenance, the Husky 1750 US has been designed for ease of access, which simplifies routine checks and servicing. This attention to maintenance leads to minimized downtime and extended machine lifespan, ultimately contributing to a more efficient production line.

Safety features are also a priority in the design of the Husky 1750 US. The machine incorporates various safety mechanisms to protect operators and reduce the risk of accidents during operation. With a strong emphasis on performance, technology, and safety, Husky 1750 US emerges as an excellent solution for businesses looking to advance their injection molding capabilities and improve overall production efficiency.
Top Page Image Contents