Husky 1750 US manual Exclusiones DE LA Cobertura EN

Page 30

Limited Warranty

This product is warranted by us to the original retail

consumer against defects in material and workmanship

for a period of one year on the machine, 90 days on

the gun + hose + lance as well as 90 days on the

ground-fault circuit interrupter (GFCI); effective from

the date of retail purchase and is not transferable.

This warranty applies only to products used in

consumer applications. This warranty does not apply

to commercial or rental applications.

Please complete and return the enclosed Customer

Information Card so that we can reach you in the

unlikely event a safety recall is needed. Register by

Internet at www.huskypowerwasher.com. Return of

this card is not required to validate this warranty.

WHAT IS COVERED: Replacement parts and labor.

WHAT IS NOT COVERED: This warranty does

not include such parts as nozzles which must be replace

as part of normal maintenance of the equipment, rather

than as the result of a defect. Transportation charges

to warranty center for defective products.

Transportation charges to consumer for repaired

products. Damages caused by abuse, accident,

improper repair, or failure to perform normal

maintenance. Use of improper chemicals or

noncompliance with the operators manuals

instructions. Sales outside of the United States or Ca-

nada. Any other expense including consequential

damages, incidental damages, or incidental expenses,

including damage to property. Some states do not

allow the exclusion or limitation of incidental or

consequential damages, so the above limitation or

exclusion may not apply to you. This warranty does

not cover damage resulting from failure to observe

any of the following conditions:

1)The inlet water pressure must be between 20 and

100 p.s.i.

2)The inlet water temperature must not exceed 90°

degree F.

3)The unit should not be stored in areas where

temperatures may drop below 32 degrees F.

Garantía limitada

Este producto está garantizado para el comprador

original en todos aquellos defectos que surjan en los

materiales y en fabricación de la máquina durante un

periodo de tiempo de un año, 90 días para la pistola

+tubo flexible + lanzas y 90 días para el interruptor

del circuito de fallos de conexión a tierra (GFCI);

comenzando su validez a partir de la fecha de com-

pra y es intransferible. Esta garantía se aplica sólo

para los productos que se utilicen en las aplicaciones

de uso y no tiene validez para usos comerciales o de

alquiler.

Complete y devuelva la anexa Tarjeta de Información

acerca del Cliente, para que podamos comunicarnos

con usted. en la improbable eventualidad de que se

haga necesario reclamar la mercancía por motivos de

seguridad. Registro por Internet al sitio:

www.huskypowerwasher.com. La restitución de dicha

tarjeta no es necesaria para los fines de la validez de la

presente garantía.

LA GARANTÍA CUBRE: piezas de repuesto

substitución y mano de obra.

EXCLUSIONES DE LA COBERTURA EN

GARANTÍA: la presente garantía no incluye aquellas

piezas que, como las boquillas, deben ser substituidas

como piezas de normal mantenimiento del equipo, y

no como consecuencia de un defecto. Los gastos por

transporte a un centro autorizado por los productos

defectuosos. Los gastos de transporte al consumidor

por los productos reparados. Los daños causados por

un mal uso, accidente, reparación impropia o falta de

mantenimiento.

El empleo de productos químicos inadecuados y el no

respeto de las instrucciones del manual para el uso. Las

ventas fuera de los Estados Unidos o de Canadá.

Cualquier otro gasto que comprenda daños indirectos,

daños accidentales o gastos accidentales, incluidos los

daños a la propiedad. Algunos Estados no permiten la

exclusión o la limitación de los daños accidentales o

indirectos; por lo tanto, dicha limitación o exclusión

podría no ser referida a usted. La presente garantía no

cubre los daños resultantes de la falta de observación

de una de las siguientes condiciones:

1)La presión del agua en entrada debe estar entre

los 20 y los 100 p.s.i.

2)La temperatura del agua en entrada no debe su-

perar los 90° F

3)El equipo no debe ser almacenado en zonas donde

la temperatura puede llegar por debajo de los 32° F.

30

Image 30
Contents Page Huskypowerwasher Serial NumberImportante Número de SeriePage Page Page Solución DE Problemas InstallationWater Connection Power Supply Operating Instructions High PressureSafety and Operation Rules Normas Operativas Y DE SeguridadWasher to maintain complete control of the wand Wear safety goggles while operatingNot recommended for use on painted surfaces Durante el uso, no cubra la máquina de lavar aGrounding Instructions Or breakdown, grounding provides a path of leastInstrucciones Para LA Toma DE Tierra Page Safety Features Características Relativas LA Seguridad Motor Overload Sobrecarga DEL MotorExtensiones Extension Cords Page Power Supply Connection Service for proper replacement partsConexión CON LA Potencia DE Alimentación Page Page Page Page Page Maintenance MantenimientoEND of Operation Cooling System Sistema DE Refrigeración LOS DañosPage Page Troubleshooting Problem Possible Cause CorrectionPage Problemas Causas Probables Solución Localización DE LAS AveríasPage Replacement Parts Accessories Piezas DE Repuesto Y AccesoriosTechnical Data See OUR WEB Site for Replacement Or Missing PartsDatos Técnicos Exclusiones DE LA Cobertura EN Fault circuit interrupter Gfci effective from the date HOW to Obtain WarrantyCómo Obtener LA Garantía Made in Italy Hecho EN Italy

1750 US specifications

The Husky 1750 US is an innovative and versatile injection molding machine designed to meet diverse manufacturing needs in the plastics industry. This machine stands out due to its blend of sophisticated technology, exceptional performance, and user-friendly features, making it an ideal choice for both small-scale and large-scale production processes.

One of the main features of the Husky 1750 US is its robust and efficient hydraulic system. This system is engineered to provide precise control over the injection process, ensuring consistent quality in each molded part. The machine's clamping unit boasts a high injection speed and rapid cycle times, enabling manufacturers to optimize their productivity. With a clamping force of 1750 tons, it caters well to a wide variety of applications, including packaging, automotive components, and medical devices.

The Husky 1750 US is equipped with cutting-edge technologies that enhance its performance. Its smart processing capabilities allow operators to monitor and adjust key parameters in real time, leading to reduced cycle times and improved energy efficiency. The machine features an advanced control system that provides intuitive user interfaces, making setup and operation effortless even for those with minimal experience.

Another key characteristic of the Husky 1750 US is its versatility. It is compatible with a wide range of molds and materials, including high-performance thermoplastics, allowing it to adapt to the needs of different production environments. This flexibility is further amplified by its modular design, enabling easy upgrades and customization to meet evolving operational demands.

In terms of maintenance, the Husky 1750 US has been designed for ease of access, which simplifies routine checks and servicing. This attention to maintenance leads to minimized downtime and extended machine lifespan, ultimately contributing to a more efficient production line.

Safety features are also a priority in the design of the Husky 1750 US. The machine incorporates various safety mechanisms to protect operators and reduce the risk of accidents during operation. With a strong emphasis on performance, technology, and safety, Husky 1750 US emerges as an excellent solution for businesses looking to advance their injection molding capabilities and improve overall production efficiency.