Not recommended for use on painted surfaces

9.Stay alert, watch what you are doing.

10.Follow maintenance instructions specified in this

manual.

11.Check power cords before using. Damaged cords

can reduce performance of pressure washer or

cause a fatal electric shock.

12.The narrow pin point stream is very powerful. It is

not recommended for use on painted surfaces,

wood surfaces or items attached with an adhesive

backing.

13.Keep operating area clear of all persons.

14.To reduce the risk of injury, close supervision is

necessary when this product is used near children

15.Always use both hands when operating pressure

washer to maintain complete control of the wand.

16.Do not touch nozzle or water spray while operating.

17.Wear safety goggles while operating.

18.Disconnect power plug from the outlet when not in

use and prior to the detaching of the high pressure

hose.

19.Never tie knots or kink the high pressure hose as

damage could result.

20.Do not operate this product in temperatures

below 32°F.

21.Carefully observe all chemical instructions and

warnings before using.

22.The pressure washer should not be used in areas

where gas vapors may be present. An electric spark

could cause an explosion or fire.

23.To minimize the amount of water getting into the

pressure washer, the unit should be placed as far

as possible from the cleaning site during operation.

24.To prevent accidental discharge, the spray gun

should be secured by locking trigger when not in

use.

25.Do not operate this product when fatigued or under

the influence of alcohol or drugs.

26.To allow free air circulation, the pressure washer

should NOT be covered during operation.

27.Know how to stop the product and bleed pressure

quickly. Be thoroughly familiar with the controls.

28.Do not over reach or stand on unstable support.

Keep good footing and balance at all times.

29.“WARNING - Risk of injection or injury - Do not

direct discharge stream at persons.”

30.See below for grounding instructions

“SAVE THESE INSTRUCTIONS”

9.Permanezca atento y observe con cuidado lo que

está haciendo.

10.Para la manutención, sigan las instrucciones

presentadas en el presente manual.

11.Antes del uso revise los cables eléctricos. Los cables

dañados no sólo reducen los rendimiento de la

máquina de lavar a presión, sino que pueden

provocar descargas eléctricas.

12.El pequeño chorro de punta de alfiler es muy po-

tente. No se aconseja su uso sobre superficies

pintadas, sobre superficies de madera o sobre

objetos con revestimiento adhesivo

13.Aleje a las personas del área de trabajo.

14.Para reducir los riesgos de lesiones, es absolutamente

necesario efectuar un control atento cuando el

producto es utilizado cerca de los niños.

15.Use siempre ambas manos cuando se utiliza la

máquina de lavar a presión, con el fin de mantener

un completo control del tubo/de la manguera.

16.No toque el boquilla o el chorro de agua cuando

está en funcionamiento.

17.Durante el uso, utilice gafas de protección.

18.Desconecte el enchufe eléctrico de la toma cuando

no está en uso e, igualmente, antes de desconectar

la manguera de alta presión.

19.Nunca anude o doble la manguera de alta presión

ya que podría dañarla.

20.No hagan funcionar este producto a

temperaturas inferiores a 32°F

21.Siga cuidadosamente todas las instrucciones con

respecto a productos químicos y las advertencias

antes del uso.

22.No hay que utilizar la máquina de lavar a presión

en áreas donde hayan vapores gaseosos. Una

eventual chispa eléctrica podría provocar una

explosión o un incendio.

23.Para reducir al máximo la cantidad de agua que

podría entrar en la máquina de lavar a presión,

durante el uso, colóquela lo más lejos posible de la

zona que debe ser limpiada.

24.Con el fin de evitar escapes accidentales, cuando

no está en uso, la pistola rociadora debe estar

asegurada con el gatillo de bloqueo.

25.No utilice el equipo cuando esté muy cansados o

cuando esté bajo la influencia de alcohol o de drogas.

26.Durante el uso, NO cubra la máquina de lavar a

presión con el fin de permitir una ventilación adecuada.

27.Aprenda cómo bloquear el producto o purgar la

presión rápidamente. Conozca el funcionamiento

de los diferentes controles.

28.No suba ni se pare detengan sobre soportes inestables.

Asuman siempre una posición firme y segura.

29.“ATENCIÓN. Riesgo de inyección o de daños.

No orienten el flujo contra las personas.”

30.Para la conexión a tierra, véanse las siguientes

instrucciones.

“CONSERVE LAS PRESENTES INSTRUCCIONES”

1750 US specifications

The Husky 1750 US is an innovative and versatile injection molding machine designed to meet diverse manufacturing needs in the plastics industry. This machine stands out due to its blend of sophisticated technology, exceptional performance, and user-friendly features, making it an ideal choice for both small-scale and large-scale production processes.

One of the main features of the Husky 1750 US is its robust and efficient hydraulic system. This system is engineered to provide precise control over the injection process, ensuring consistent quality in each molded part. The machine's clamping unit boasts a high injection speed and rapid cycle times, enabling manufacturers to optimize their productivity. With a clamping force of 1750 tons, it caters well to a wide variety of applications, including packaging, automotive components, and medical devices.

The Husky 1750 US is equipped with cutting-edge technologies that enhance its performance. Its smart processing capabilities allow operators to monitor and adjust key parameters in real time, leading to reduced cycle times and improved energy efficiency. The machine features an advanced control system that provides intuitive user interfaces, making setup and operation effortless even for those with minimal experience.

Another key characteristic of the Husky 1750 US is its versatility. It is compatible with a wide range of molds and materials, including high-performance thermoplastics, allowing it to adapt to the needs of different production environments. This flexibility is further amplified by its modular design, enabling easy upgrades and customization to meet evolving operational demands.

In terms of maintenance, the Husky 1750 US has been designed for ease of access, which simplifies routine checks and servicing. This attention to maintenance leads to minimized downtime and extended machine lifespan, ultimately contributing to a more efficient production line.

Safety features are also a priority in the design of the Husky 1750 US. The machine incorporates various safety mechanisms to protect operators and reduce the risk of accidents during operation. With a strong emphasis on performance, technology, and safety, Husky 1750 US emerges as an excellent solution for businesses looking to advance their injection molding capabilities and improve overall production efficiency.