Husky 1750 US manual Maintenance, Mantenimiento, END of Operation

Page 20

4.7END OF OPERATION

When you have completed use of the chemical injection

system, continue to run in low pressure position and

flush clean water through the chemical tank until it is

thoroughly cleaned. NOTE: Failure to clean properly

will cause the injection system to become clogged and

inoperable.

lStop the unit by pressing to ON/OFF button

lDisconnect electrical plug

lTurn off water and depressurize unit by squeezing

trigger.

WARNING: Turn off water supply and

squeeze trigger to depressurize the unit.

Failure to do so could result in personal injury

CAUTION

due to discharge of high pressure water.

lDisconnect the high pressure discharge hose and

the water inlet hose.

5.0MAINTENANCE

5.1CONNECTIONS

Connections on Pressure Washer hoses, gun and spray

wand should be cleaned regularly and lubricated with

non-water soluable grease to prevent leakage and

damage to the o-rings.

5.2NOZZLE

The high pressure/low pressure adjustment of the

nozzle should be lubricated with non-water soluable

grease regularly. Clogging of the nozzle causes the

pump pressure to be too high and cleaning is

immediately required.

1.Clear blockage in nozzle by forcing stiff wire

through center hole.

2.Backflush the nozzle with water

Restart the pressure washer and depress the trigger

on the spray gun. If the pressure is still too high,

repeat above items 1-2.

5.3LUBRICATION

The pressure washer is designed with a permanent

lubrication system. Conventional oil check and oil

changes are not necessary.

NOTE: IN CASE OF OIL LEAKAGE, CONTACT THE

HD POWERWASHER CUSTOMER SERVICE

DEPARTMENT CONCERNING REPAIR. A SMALL

AMOUNT OF OIL LEAKAGE IS NORMAL.

5.4WATER SCREEN

The pressure washer is equipped with a water inlet

screen to protect the pump.

CAUTION: if the screen is not kept clean,

the flow of water to the pressure washer

will be restricted and the pump may be

CAUTION

damaged.

4.7FINALIZACIÓN DE LA OPERACIÓN

Cuando haya terminado de utilizar el sistema de

inyección de productos químicos, haga funcionar

aún a baja presión y haga pasar agua limpia por el

depósito del líquido detergente hasta que esté com-

pletamente limpio. NOTA: la falta de una limpieza

a fondo puede provocar una obturación en el siste-

ma de inyección y será inutilizable.

lDetenga el equipo presionando el botón on/off.

lDesconecte la toma eléctrica.

lCierre el agua y depresurice el equipo

presionando el gatillo.

ATENCIÓN: cierren la suministro de agua

y presione el gatillo para depresurizar el

equipo. La falta de despresurización puede

ATENCIÓN provocar daños a las personas debido a la

descarga del agua de alta presión.

lDesconecte la manguera de descarga de la alta

presión y la manguera de introducción del agua.

5.0MANTENIMIENTO

5.1 CONEXIONES

Las conexiones a mangueras, la pistola y el tubo de

chorro de la hidrolimpiadora, deberían ser limpiados

regularmente y lubricados para prevenir las pérdidas

y la rotura de los aros tóricos.

5.2BOQUILLA

El dispositivo de regulación de la alta/baja presión de la

boquilla debe ser lubricado con regularidad. La

obturación de la boquilla provoca el aumento de la

presión de la bomba. Se requiere una limpieza inmediata.

1.Eliminen el bloqueo en la boquilla forzando el

cable rígido a través el agujero central.

2.Dejen pasar el agua a través la boquilla

Reinicie arrancar nuevamente la máquina de lavar a

presión y oprimir el gatillo de la pistola de chorro. Si

la boquilla está aún bloqueada o parcialmente

bloqueada, repita dichas operaciones desde el punto

1 hasta el punto 2.

5.3LUBRICACIÓN

La máquina de lavar a presión ha sido creada con un

sistema de lubricación permanente. No son necesarios

controles convencionales ni la substitución de aceites.

NOTA: EN EL CASO DE PÉRDIDA DE ACEITE,

CONTACTEN AL DEPARTAMENTO DE SERVICIO

AL CLIENTE DE HUSKYPOWERWASHER, SECCIÓN

REPARACIONES. UNA PEQUEÑA PÉRDIDA DE

ACEITE ES NORMAL.

5.4FILTRO DE AGUA

La máquina de lavar a presión está dotada de un filtro

de introducción de agua para proteger la bomba.

ATENCIÓN: si no se mantiene limpio el

filtro, el flujo del agua hacia la máquina

de lavar a presión se ve limitado y la bom-

ATENCIÓN ba puede dañarse.

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Page Huskypowerwasher Serial NumberImportante Número de SeriePage Page Page Installation Water Connection Power Supply Operating InstructionsSolución DE Problemas High PressureSafety and Operation Rules Normas Operativas Y DE SeguridadWear safety goggles while operating Not recommended for use on painted surfacesWasher to maintain complete control of the wand Durante el uso, no cubra la máquina de lavar aInstrucciones Para LA Toma DE Tierra Grounding InstructionsOr breakdown, grounding provides a path of least Page Extensiones Extension Cords Safety Features Características Relativas LA SeguridadMotor Overload Sobrecarga DEL Motor Page Conexión CON LA Potencia DE Alimentación Power Supply ConnectionService for proper replacement parts Page Page Page Page Page END of Operation MaintenanceMantenimiento Cooling System Sistema DE Refrigeración LOS DañosPage Page Troubleshooting Problem Possible Cause CorrectionPage Problemas Causas Probables Solución Localización DE LAS AveríasPage Replacement Parts Accessories Piezas DE Repuesto Y AccesoriosDatos Técnicos Technical DataSee OUR WEB Site for Replacement Or Missing Parts Exclusiones DE LA Cobertura EN Cómo Obtener LA Garantía Fault circuit interrupter Gfci effective from the dateHOW to Obtain Warranty Made in Italy Hecho EN Italy

1750 US specifications

The Husky 1750 US is an innovative and versatile injection molding machine designed to meet diverse manufacturing needs in the plastics industry. This machine stands out due to its blend of sophisticated technology, exceptional performance, and user-friendly features, making it an ideal choice for both small-scale and large-scale production processes.

One of the main features of the Husky 1750 US is its robust and efficient hydraulic system. This system is engineered to provide precise control over the injection process, ensuring consistent quality in each molded part. The machine's clamping unit boasts a high injection speed and rapid cycle times, enabling manufacturers to optimize their productivity. With a clamping force of 1750 tons, it caters well to a wide variety of applications, including packaging, automotive components, and medical devices.

The Husky 1750 US is equipped with cutting-edge technologies that enhance its performance. Its smart processing capabilities allow operators to monitor and adjust key parameters in real time, leading to reduced cycle times and improved energy efficiency. The machine features an advanced control system that provides intuitive user interfaces, making setup and operation effortless even for those with minimal experience.

Another key characteristic of the Husky 1750 US is its versatility. It is compatible with a wide range of molds and materials, including high-performance thermoplastics, allowing it to adapt to the needs of different production environments. This flexibility is further amplified by its modular design, enabling easy upgrades and customization to meet evolving operational demands.

In terms of maintenance, the Husky 1750 US has been designed for ease of access, which simplifies routine checks and servicing. This attention to maintenance leads to minimized downtime and extended machine lifespan, ultimately contributing to a more efficient production line.

Safety features are also a priority in the design of the Husky 1750 US. The machine incorporates various safety mechanisms to protect operators and reduce the risk of accidents during operation. With a strong emphasis on performance, technology, and safety, Husky 1750 US emerges as an excellent solution for businesses looking to advance their injection molding capabilities and improve overall production efficiency.
Top Page Image Contents