Safety and Operation Rules | Husky 1750 US specs

1.0 SAFETY AND OPERATION

RULES

Safety precautions are essential when any mechanical

equipment is involved. These precautions are necessary

when using, storing, and servicing mechanical

equipment. Using this equipment with the respect and

caution demanded will considerably lessen the

possibilities of personal injury. If safety precautions are

overlooked or ignored, personal injury or property

damage may occur.

The following symbols shown below are used

extensively throughout this manual. Always heed these

precautions, as they are essential when using any

mechanical equipment.

This warning symbol identifies specific

instructions or procedures which if not

correctly followed could result in perso- WARNING nal injury or death.

This caution symbol identifies specific

instructions or procedures which, if not

strictly observed, could result in damage CAUTION to, or destruction of equipment.

This unit was designed for specific applications. It should

not be modified and/or used for any application other

than that which it was designed.

When using this product basic precautions

should always be followed, including the

following:.

WARNING

1.Read this manual carefully - know your equipment.

Consider the applications, limitations, and the

potential hazards specific to your unit.

2.Outlets with a third prong ground are required.

Do not use without grounded prong..

3.Do not touch plug or outlet with wet hands.

4.Avoid accidental starts. Move switch on unit to

“OFF” position before connecting or disconnecting

cord to electrical outlets.

5.Water spray must never be directed towards any

electric wiring or directly towards the pressure

washer machine itself or fatal electric shock may

occur.

6.Never carry your pressure washer by the cord. Do

not pull on the cord to disconnect from the outlet.

7.To prevent damage, the cord should not be crushed,

placed next to sharp objects or near a heat source.

8.This product is provided with a Ground Fault Circuit

Interrupter built into the power cord plug. If

replacement of the plug or cord is needed, use

only identical replacement parts.

1.0 NORMAS OPERATIVAS Y DE

SEGURIDAD

Cuando se trata de un equipo mecánico, las precauciones

inherentes a la seguridad son esenciales.

Por ello es necesario adoptar dichas precauciones duran-

te el uso, el almacenamiento y la mantenimiento del equipo

mecánico. Utilizando los aparatos con el respeto y la

cautela requeridos, las posibilidades de provocar lesiones

personales disminuirán notablemente. Si se pasan por

alto o no se consideran estas precauciones de seguridad,

podrían producirse lesiones en las personas o daño al

equipo. Los símbolos que describiremos a continuación

son utilizados ampliamente en el presente manual. Tenga

siempre en cuenta dichas precauciones puesto que son

esenciales cuando se utiliza el equipo mecánico.

Es el símbolo que identifica las

instrucciones para procedimientos

específicos; si no son seguidas, pueden

PELIGRO

provocar lesiones personales o la muerte.

Este símbolo identifica las instrucciones

de procedimientos específicos que si no

son observadas rigurosamente pueden

provocar daños o hasta la destrucción

IMPORTANTE

del equipo mismo.

Esta unidad ha sido diseñada para aplicaciones

específicas. No se debería modificar y/o utilizar para

aplicaciones diferentes de aquellas para las cuales ha

sido pensada.

Cuando el equipo es utilizado, hay que

seguir precauciones básicas, entre las

cuales se encuentran las siguientes:

PELIGRO

1.Lea atentamente el presente manual para conocer

su equipo. Tome en debida consideración sus

aplicaciones, limitaciones y los potenciales riesgos

específicos.

2.Se necesitan enchufes con una tercera punta con toma

a tierra. No utilice enchufes sin la toma de tierra.

3.No toque el enchufe o la toma con las manos

mojadas.

4.Eviten encendidos accidentales. Coloque el

interruptor en APAGADO antes de conectar o

desconectar el cable eléctrico a una toma.

5.No dirija nunca el chorro del agua sobre

instalaciones eléctricas o sobre la misma máquina

de lavar a presión, con el fin de evitar descarga

eléctrica.

6.No utilice el cable para mover la máquina de

lavar a presión. No tire del cable para desconectar

el equipo de la toma.

7.Con el fin de evitar daños, el cable no debe ser

aplastado, no debe ser colocado cerca de objetos

cortantes ni de fuentes de calor.

8.Este producto es suministrado con un interruptor

de circuito con conexión a tierra insertado en el

enchufe del cable de alimentación. Si fuera

necesario cambiar el enchufe o el cable, utilicen

piezas de repuesto del mismo tipo.

1750 US specifications

The Husky 1750 US is an innovative and versatile injection molding machine designed to meet diverse manufacturing needs in the plastics industry. This machine stands out due to its blend of sophisticated technology, exceptional performance, and user-friendly features, making it an ideal choice for both small-scale and large-scale production processes.

One of the main features of the Husky 1750 US is its robust and efficient hydraulic system. This system is engineered to provide precise control over the injection process, ensuring consistent quality in each molded part. The machine's clamping unit boasts a high injection speed and rapid cycle times, enabling manufacturers to optimize their productivity. With a clamping force of 1750 tons, it caters well to a wide variety of applications, including packaging, automotive components, and medical devices.

The Husky 1750 US is equipped with cutting-edge technologies that enhance its performance. Its smart processing capabilities allow operators to monitor and adjust key parameters in real time, leading to reduced cycle times and improved energy efficiency. The machine features an advanced control system that provides intuitive user interfaces, making setup and operation effortless even for those with minimal experience.

Another key characteristic of the Husky 1750 US is its versatility. It is compatible with a wide range of molds and materials, including high-performance thermoplastics, allowing it to adapt to the needs of different production environments. This flexibility is further amplified by its modular design, enabling easy upgrades and customization to meet evolving operational demands.

In terms of maintenance, the Husky 1750 US has been designed for ease of access, which simplifies routine checks and servicing. This attention to maintenance leads to minimized downtime and extended machine lifespan, ultimately contributing to a more efficient production line.

Safety features are also a priority in the design of the Husky 1750 US. The machine incorporates various safety mechanisms to protect operators and reduce the risk of accidents during operation. With a strong emphasis on performance, technology, and safety, Husky 1750 US emerges as an excellent solution for businesses looking to advance their injection molding capabilities and improve overall production efficiency.