Delta DTT2450 instruction manual Operating Instructions, Basic Elements of a Pressure Washer

Page 7

OPERATING INSTRUCTIONS

Compare the illustrations with your unit to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference.

 

Chemical

 

Hose

 

High

Spray

Pressure

Gun

Hose

Multi-

Engine

 

Adjustable

 

Spray Wand

 

High Pressure Pump (located inside the shroud)

BASIC ELEMENTS OF A PRESSURE WASHER

High Pressure Pump (located inside the shroud): Increases the pressure of the water supply.

Engine: Drives the high pressure pump.

High Pressure Hose: Carries the pressurized water from the pump to the gun and spray wand.

Spray Gun: Connects with spray wand to control water flow rate, direction, and pressure.

Multi-Adjustable Spray Wand: Allows the user to use high or low pressure and adjusts from a pencil stream (0°) to a wide angle fan spray (40°). See How To Use Spray Wand instructions in this section.

Chemical Hose: Feeds cleaning agents into the pump to mix with the water. See How To Apply Chemicals/Cleaning Solvents instructions in this section.

BASIC ELEMENTS OF AN ENGINE

Refer to the engine manual for location and operation of engine controls.

Primer Button: Injects fuel directly into the carburetor manifold for easier cold engine starting.

Starter Grip: Pulling starter grip operates recoil starter to crank engine.

Throttle Control Lever: Controls engine speed.

PRESSURE WASHER

TERMINOLOGY

PSI: Pounds per Square Inch. The unit of measure for water pressure. Also used for air pressure, hydraulic pressure, etc.

GPM: Gallons Per Minute. The unit of measure for the flow rate of water.

CU: Cleaning Units. GPM multiplied by PSI. GPM x PSI = CU.

7- ENG

A04032

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Structioin N M Anual Important Safety Instructions Consumer Safety InformationRisk of Explosion or Fire Risk to Breathing Risk of Explosion or FireRisk to Fluid Injection Risk of Electrical Shock Risk of Chemical BurnRisk of HOT Surfaces Risk of Injury from Spray Risk of Unsafe OperationCarton Contents Pressure Washer Terminology Operating InstructionsBasic Elements of a Pressure Washer Basic Elements of AN EnginePressure Washer Operating Features Low Pressure HOW to Apply Chemicals and Cleaning SolventsHigh Pressure 40º fan spray 0º pencil streamShutting Down StartingEngine Pump MaintenanceNozzle Cleaning HOW to Clean the Water Inlet FilterEngine StoragePressure Washer Trouble Shooting Guide Connection Water leaking After periodNormal use Water leaking at Gun/spray wandENG A04032 Warranty

DTT2450 specifications

The Delta DTT2450 is a cutting-edge temperature and humidity data logger that caters to a wide array of industrial and scientific applications. Renowned for its precision and reliability, this device is integral in environments such as pharmaceutical, food storage, and environmental monitoring, where maintaining specific temperature and humidity levels is crucial.

One of the main features of the Delta DTT2450 is its dual-channel capability, allowing simultaneous measurement of both temperature and humidity. This enhances its versatility, enabling users to monitor two critical environmental parameters with a single device. The logger boasts a wide measurement range, with temperature readings typically spanning from -40°C to +80°C and humidity levels from 0% to 100% relative humidity. This broad range makes it suitable for a variety of settings.

The device operates using an advanced semiconductor and capacitive sensor technology, resulting in excellent accuracy and response time. The DTT2450 is designed with user-friendliness in mind, equipped with a large, easy-to-read LCD display that provides real-time data monitoring. Additionally, its intuitive interface allows for easy navigation through settings and data retrieval, even for users with minimal technical expertise.

A notable characteristic of the Delta DTT2450 is its data storage capability. It can store a significant amount of data points, allowing for extensive logging periods without the need for frequent data downloading. The logger supports various data sampling rates, customizable according to user requirements, ensuring optimal data collection in varying scenarios.

Connectivity is facilitated via USB, enabling quick and straightforward data transfer to computers for analysis. The device is compatible with specialized software that provides comprehensive data analysis and reporting tools, aiding in compliance with industry standards.

With a robust design, the DTT2450 can withstand challenging environmental conditions, making it a dependable choice for both indoor and outdoor use. It is also equipped with a long-lasting battery, ensuring extended operational periods and reducing maintenance interruptions.

In summary, the Delta DTT2450 stands out for its dual-channel monitoring, accuracy, and user-friendly design, making it an excellent investment for businesses and organizations keen on maintaining optimal environmental conditions effectively.
Top Page Image Contents