Pressure Washer Operating Features

PRESSURE WASHER

TERMINOLOGY (cont'd)

Bypass Mode: Allows water to re-circulate within pump when the gun trigger is not pulled.

Allowing the unit to run for more than

two minutes without the gun trigger pulled could cause overheating and damage to the pump.

Chemical Injection System: Mixes cleaners or cleaning solvents with the water to improve cleaning effectiveness.

Water Supply: All pressure washers must have a source of water. The minimum requirements for a water supply are 20 PSI and 5 gallons per minute.

PRESSURE WASHER OPERATING FEATURES

PRESSURE ADJUSTMENTS

The pressure setting is preset at the factory to achieve optimum pressure and cleaning. If you need to lower the pressure, it can be accomplished by these methods.

1.Back away from the surface to be cleaned. The further away you are, the less the pressure will be on the surface to be cleaned.

2.Rotate the nozzle at the end of the multi-adjustable spray wand to widen the fan spray. The wider fan spray will minimize the pressure on the surface to be cleaned.

DO NOT attempt to increase pump

pressure. A higher pressure setting than the factory set pressure may damage pump.

3.Reduce the speed of the gasoline engine (RPM). Slow the engine down and the water pressure will go down with it.

READ AND UNDERSTAND ALL WARNINGS BEFORE STARTING UNIT

When using the high pressure setting, DO NOT allow the high pressure spray to come in contact with unprotected skin, eyes, or with

any pets or animals. Serious injury can occur.

Your washer operates at fluid pressures and velocities high enough to penetrate human and animal flesh, which could result in amputation or other serious injury. Leaks caused by loose fittings or worn or damaged hoses can result in injection injuries. DO NOT TREAT

FLUID INJECTION AS A SIMPLE CUT! See a physician immediately!

NEVER fill fuel tank when engine is running or hot. Do not smoke when filling fuel tank.

NEVER fill fuel tank completely. Fill tank to 1/2" below bottom of filler neck to provide space for fuel expansion. Wipe any fuel spillage from engine and equipment before starting engine.

NEVER run engine indoors or in enclosed, poorly ventilated areas. Engine exhaust con- tains carbon monoxide, an odorless and deadly gas.

DO NOT let hoses come in contact with very hot engine muffler during or immediately after use of your pressure washer. Damage to hoses from contact with hot engine surfaces will NOT be covered by warranty.

NEVER pull water supply hose to move pressure washer. This could damage hose and/or pump inlet.

DO NOT use hot water, use cold water only.

NEVER turn water supply off while pressure washer engine is running or damage to pump will result.

DO NOT stop spraying water for more than two minutes at a time. Pump operates in bypass mode when spray gun trigger is not pressed. If pump is left in bypass mode for more than two minutes internal components of the pump can be damaged.

If you do not understand these precautions, please call 1-866-422-4286 to speak to a service representative for further instructions.

A04032

8- ENG

DTT2450 specifications

The Delta DTT2450 is a cutting-edge temperature and humidity data logger that caters to a wide array of industrial and scientific applications. Renowned for its precision and reliability, this device is integral in environments such as pharmaceutical, food storage, and environmental monitoring, where maintaining specific temperature and humidity levels is crucial.

One of the main features of the Delta DTT2450 is its dual-channel capability, allowing simultaneous measurement of both temperature and humidity. This enhances its versatility, enabling users to monitor two critical environmental parameters with a single device. The logger boasts a wide measurement range, with temperature readings typically spanning from -40°C to +80°C and humidity levels from 0% to 100% relative humidity. This broad range makes it suitable for a variety of settings.

The device operates using an advanced semiconductor and capacitive sensor technology, resulting in excellent accuracy and response time. The DTT2450 is designed with user-friendliness in mind, equipped with a large, easy-to-read LCD display that provides real-time data monitoring. Additionally, its intuitive interface allows for easy navigation through settings and data retrieval, even for users with minimal technical expertise.

A notable characteristic of the Delta DTT2450 is its data storage capability. It can store a significant amount of data points, allowing for extensive logging periods without the need for frequent data downloading. The logger supports various data sampling rates, customizable according to user requirements, ensuring optimal data collection in varying scenarios.

Connectivity is facilitated via USB, enabling quick and straightforward data transfer to computers for analysis. The device is compatible with specialized software that provides comprehensive data analysis and reporting tools, aiding in compliance with industry standards.

With a robust design, the DTT2450 can withstand challenging environmental conditions, making it a dependable choice for both indoor and outdoor use. It is also equipped with a long-lasting battery, ensuring extended operational periods and reducing maintenance interruptions.

In summary, the Delta DTT2450 stands out for its dual-channel monitoring, accuracy, and user-friendly design, making it an excellent investment for businesses and organizations keen on maintaining optimal environmental conditions effectively.