Craftsman 919.670281, D2415 Pressure Washer Maintenance, Purge Pump of Air and Contaminants

Page 12

Pressure Washer Maintenance

Check and Clean Inlet Screen: Examine inlet screen on pump inlet fitting. Clean if clogged; replace if torn.

Check High Pressure Hose: High pressure hose can develop leaks from wear, kinking, abuse. Inspect hose each time before use. Check for cuts, leaks, abrasions or bulging of cover, and damage or movement of couplings. If any of these conditions exist, replace hose immediately.

Check Chemical/Soap Hose: Examine the chemical/soap hose and clean if clogged. Hose should fit tightly on pump fitting. Check for leaks and tears. Replace filter or hose if either is damaged.

Check Gun and Wand: Examine hose connection to gun making sure it is secure. Test trigger by pressing it and making sure it springs back into place when you release it.

Pump Maintenance (Changing Pump Oil)

The pump on your pressure washer was shipped from the factory with oil. The oil in your pump must be changed every 50 hours.

•Run engine until it runs out of fuel. Otherwise, fuel can leak out, creating a fire/explosion hazard, when you tip engine.

•Disconnect spark plug wire and keep it away from spark plug.

•Drain engine oil. See Changing Oil on page 13.

Used oil is a hazardous waste product. Dispose of used oil properly. Do not discard with household waste.

Check with your local authorities for safe disposal/recycling facilities.

•Using a 5/16" Allen wrench remove pump oil drain plug.

Oil Drain Plug

•Tilt unit and drain pump oil into appropriate container.

•Fill pump with 10 ounces of R&O 150 oil. NOTE: If unable to find R&O 150 oil, use 30W non- detergent oil.

•Replace oil drain plug and tighten securely.

•Refill engine with oil and fuel. See Engine Oil on page 8.

Purge Pump of Air and Contaminants

To remove the air from the pump, follow these steps:

•Set up the pressure washer as described in ASSEMBLY section and connect the water supply.

•Remove the wand extension from the spray gun.

•Pull the trigger on the gun and hold.

To remove the contaminants from the pump, follow these steps:

•Set up the pressure washer as described in ASSEMBLY section, connect the water supply.

•Remove the wand extension from the spray gun.

•Start the engine according to instructions in the OPERATION section.

•Pull the trigger on the gun and hold.

•When the water supply is steady and constant, disengage trigger and refasten the wand extension.

Engine Maintenance

Check Oil Level

•Oil level should be checked prior to each use or at least every 5 hours of operation. To check oil see Engine Oil on page 8.

D24150

12 - ENG

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Horsepower PSI 2.4 GPM High Pressure Washer Sold by Sears Canada, Inc., Toronto, Ont. M5B2B8Table of Contents Safety Guidelines Definitions Important Safety InstructionsRisk of Unsafe Operation Assembly Parts Bag ContentsTools Required for Assembly Adjustable wrench Mm Allen wrench suppliedRemove Pressure Washer from Carton Preparing the Pressure Washer for First UseChecklist OperationKnow Your High Pressure Washer Recoil STARTER- Used for starting the engineStopping Your Pressure Washer Before Starting The EngineEngine Oil GasolineTo Start Your Pressure Washer Adjusting Fan Spray How To Use Your Pressure Washer Adjusting Chemical FlowMaintenance Product SpecificationsPressure Washer Specifications Engine SpecificationsPressure Washer Maintenance Engine Maintenance Check Oil LevelPump Maintenance Changing Pump Oil Purge Pump of Air and ContaminantsClean Pre-Cleaner and Air Cleaner Cartridge Clean and Replace Spark PlugChanging Engine Oil Check Engine Finger Guard/MufflerService and Adjustments Nozzle CleaningCarburetor Storage Preparing Pressure Washer for StorageEngine Preparation Pump PreparationEngine will not start No or low pressureInitial use Will not draw chemicalsNo or low pressure after Period of normal useWater leaking at gun/wand ConnectionIf calling locally, please use one of the following numbers Sold By Sears Canada, Inc., Toronto, Ont. M5B 2B8Guide DE L’UTILISATEUR Vendu par Sears Canada, Inc., Toronto, Ont. M5B 2B8Table DES Matières FonctionnementEntretien Mesures DE Sécurité Définitions Mesures DE Sécurité ImportantesRisque DE Surfaces Assemblage Contenu de l’emballageContenu du sac Outils requis pour l’assemblage Fonctionnement Liste de vérificationBien connaître votre Génératrice Arrêt de l’appareil de lavage sous pression Avant de démarrer le moteurHuile moteur Plus froid ----40F 4C---- plus chaud Synthétique 5W-30Démarrage de l’appareil de lavage sous pression Utilisation de l’appareil de lavage sous pression Réglage du débit des produits chimiquesRéglage du jet Utilisation de savons/produits chimiquesRecommandations générales EntretienAvant Toutes les Chaque Heures ou Vérification du niveau d’huileEntretien de l’appareil de lavage sous pression Entretien de la pompe changement de l’huile de la pompeEntretien du moteur Nettoyage et remplacement de la bougie d’allumage Changement de l’huile moteurVérification du protecteur et du silencieux du moteur Entretien ET Réglages CarburateurNettoyage de la buse Entreposage Préparation du moteurLe moteur ne démarre pas Aucune pression ou basseAspiré Dutilisation normale Fuite deau au niveau de laConnexion du pistolet/lance PompeGuide DE L’UTILISATEUR Vendu par Sears Canada, Inc., Toronto, Ont. M5B 2B8

D2415, 919.670281 specifications

The Craftsman 919.670281, D2415 is a versatile and robust air compressor that is essential for both home and professional use. This model combines efficiency, reliability, and power, making it a popular choice among DIY enthusiasts and contractors alike.

One of the standout features of the Craftsman 919.670281 is its powerful motor. With a 1.5 horsepower motor, this air compressor can easily handle a variety of tasks, ranging from inflating tires to powering tools like nail guns and paint sprayers. Its high-performance capabilities ensure that it can keep up with the demands of various jobs, providing a steady air supply whenever needed.

The design of the Craftsman 919.670281 is notable for its portability. Equipped with a sturdy handle and compact footprint, this compressor can be easily transported from one location to another, whether you are working in your garage or on a construction site. The lightweight build also contributes to its user-friendliness, allowing operators to move it around without any hassle.

Another essential characteristic of this model is its oil-free pump design. This feature not only reduces maintenance but also enhances longevity, as it eliminates the need for regular oil changes. The oil-free operation leads to cleaner air output, making it a better option for applications that require a non-oiled air supply, such as spray painting or automotive work.

The Craftsman 919.670281 also boasts a 6-gallon tank capacity, enabling it to store ample air pressure for extended use. This tank size strikes a perfect balance, ensuring that sufficient air is available while still remaining portable. The quick recovery time allows users to get back to work without prolonged interruptions, making it efficient for time-sensitive tasks.

Additionally, the compressor is equipped with a user-friendly control panel, featuring easy-to-read gauges and a simple on/off switch. This intuitive setup enables users to monitor pressure levels and operate the unit with minimal effort, even for those who are new to air compressors.

In summary, the Craftsman 919.670281, D2415 is a dependable air compressor that combines powerful performance with user-friendly features. Its portability, oil-free pump design, and 6-gallon tank capacity make it ideal for a wide range of applications, solidifying its position as a crucial tool for both home improvement projects and professional work environments. Whether for inflating, nailing, or painting, this compressor delivers efficiency and reliability, making it a valuable addition to any toolkit.
Top Page Image Contents