Craftsman 919.670281, D2415 Tools Required for Assembly, Remove Pressure Washer from Carton

Page 6

Tools Required for Assembly

Adjustable wrench

5 mm Allen wrench (supplied)

Remove Pressure Washer from Carton

•Open carton from the top. Locate and remove from box the handle, gun, wand, chemical hose, oil parts bag.

•Cut carton along dotted lines.

•Remove all carton inserts.

•Roll unit through opening in carton.

NOTE: The hose is located at the bottom of the box.

Preparing the Pressure Washer for First Use

Note: Included with your pressure washer is a video cassette tape on how to prepare your unit for operation. It is recommended you view this tape before performing the next steps.

1. Insert handle onto frame.

•Insert knobs into the threaded slot in front of the frame handle and tighten by turning in a clockwise direction.

•Slide bolts into the slot in the side of the frame handle and tighten the nuts by turning in a clock-wise direction.

Insert bolt and tighten

lock nut.

Tighten knob in

clockwise direction

2. Using an adjustable wrench, remove nut from bolt that attaches board to frame. Remove wood plank from the frame of the unit. Discard bolt and board.

3.Mount the rubber isolator to the frame. To

mount isolator place threaded end of bolt through the washer.

•Next with washer on bolt place threaded end of bolt through the larger hole in bottom of the rubber isolator.

•Place threaded portion of bolt through the same hole location the wood plank was mounted to on the pressure washer.

•Next place the tee nut over the threaded portion of the bolt and use the Allen wrench provided to tighten isolator to the frame.

TEE NUT

PRESSUREISOLATOR

WASHER

FRAME

WASHER

BOLT

4.Connect wand extension to gun. To tighten, turn knob in clockwise direction. Hand tighten.

5.Remove tie wrap off of high pressure hose. Unwind high pressure hose and attach the threaded end to the gun. Tighten with adjustable wrench.

6.Connect high pressure hose to outlet on pressure washer and hand tighten firmly.

HIGH

PRESSURE

HOSE

NOTE: Always keep hose away from engine muffler.

D24150

6 - ENG

Page 5 Page 7
Image 6
Page 5 Page 7
Contents
Horsepower PSI 2.4 GPM High Pressure Washer Sold by Sears Canada, Inc., Toronto, Ont. M5B2B8Table of Contents Safety Guidelines Definitions Important Safety InstructionsRisk of Unsafe Operation Assembly Parts Bag ContentsRemove Pressure Washer from Carton Tools Required for AssemblyAdjustable wrench Mm Allen wrench supplied Preparing the Pressure Washer for First UseKnow Your High Pressure Washer ChecklistOperation Recoil STARTER- Used for starting the engineEngine Oil Stopping Your Pressure WasherBefore Starting The Engine GasolineTo Start Your Pressure Washer Adjusting Fan Spray How To Use Your Pressure Washer Adjusting Chemical FlowPressure Washer Specifications MaintenanceProduct Specifications Engine SpecificationsPump Maintenance Changing Pump Oil Pressure Washer MaintenanceEngine Maintenance Check Oil Level Purge Pump of Air and ContaminantsChanging Engine Oil Clean Pre-Cleaner and Air Cleaner CartridgeClean and Replace Spark Plug Check Engine Finger Guard/MufflerService and Adjustments Nozzle CleaningCarburetor Engine Preparation StoragePreparing Pressure Washer for Storage Pump PreparationInitial use Engine will not startNo or low pressure Will not draw chemicalsWater leaking at gun/wand No or low pressure afterPeriod of normal use ConnectionIf calling locally, please use one of the following numbers Sold By Sears Canada, Inc., Toronto, Ont. M5B 2B8Guide DE L’UTILISATEUR Vendu par Sears Canada, Inc., Toronto, Ont. M5B 2B8Table DES Matières FonctionnementEntretien Mesures DE Sécurité Définitions Mesures DE Sécurité ImportantesRisque DE Surfaces Assemblage Contenu de l’emballageContenu du sac Outils requis pour l’assemblage Fonctionnement Liste de vérificationBien connaître votre Génératrice Huile moteur Arrêt de l’appareil de lavage sous pressionAvant de démarrer le moteur Plus froid ----40F 4C---- plus chaud Synthétique 5W-30Démarrage de l’appareil de lavage sous pression Réglage du jet Utilisation de l’appareil de lavage sous pressionRéglage du débit des produits chimiques Utilisation de savons/produits chimiquesAvant Toutes les Chaque Heures ou Recommandations généralesEntretien Vérification du niveau d’huileEntretien de l’appareil de lavage sous pression Entretien de la pompe changement de l’huile de la pompeEntretien du moteur Nettoyage et remplacement de la bougie d’allumage Changement de l’huile moteurVérification du protecteur et du silencieux du moteur Entretien ET Réglages CarburateurNettoyage de la buse Entreposage Préparation du moteurLe moteur ne démarre pas Aucune pression ou basseAspiré Connexion du pistolet/lance Dutilisation normaleFuite deau au niveau de la PompeGuide DE L’UTILISATEUR Vendu par Sears Canada, Inc., Toronto, Ont. M5B 2B8