Black & Decker PW1600, PW1750, 598667-00 Accessories, Relocating Unit, Surface Preparation

ACCESSORIES

CAUTION: Before changing accessories, adjusting pressure, or engaging detergent draw system, switch the unit off, pull trigger to release pressure, and activate gun safety catch.

•ADJUSTABLE FAN WAND

3.) To remove, push turbo wand into gun wand and twist as shown in Figure 20.

20

•DETERGENT DISPENSER

23

5.) Apply detergent as directed by the detergent manufacturer.

furniture. Insure that all doors and windows are closed tight. Also make sure that all plants and trees in the adjacent area are protected by a drop cloth ensuring that they will not be harmed by any over spray.

RELOCATING UNIT

1.) To move unit to another location during cleaning, switch off unit before moving it.

1.) Insert the fan wand (D) into the gun wand (F) by pushing and rotating until the two parts are locked as shown in Figure 16.

16

2.) To obtain maximum pressure, rotate the fan wand nozzle in a clockwise direction as shown in Figure 17. This narrow stream results in deeper cleaning in a concentrated area. For a wider fan pattern rotate the fan wand nozzle in the counterclockwise direction. The wider fan pattern reduces the risk of surface damage and allows for cleaning large surface areas quickly.

17

3.) To remove, push fan wand into gun wand and twist as shown in Figure 18.

18

•TURBO NOZZLE

1.) Insert the turbo nozzle wand (C) into the gun wand (F) by pushing and rotating until the two parts are locked as shown in Figure 19.

19

Follow detergent manufacturer’s label directions for mixing correct concentrations of soap and detergents.

To use the detergent dispenser:

1.) Pull locking tab upwards as shown in Fig. 21 and pull tank out of unit.

21

O

I

2.) Lift up to remove cap as shown in Figure 22, fill tank with detergent and replace cap. Reinsert tank fully into unit until locking tab snaps into place.

22

3.) Insert the adjustable fan wand into gun. Detergent applicator will only work with adjustable fan wand.

4.) With the on-off switch in “off” (O) position, pull the adjustable fan wand nozzle outwards as shown in Figure 23 to allow detergent pick up. Put on-off switch in “on” (I) position.

8

6.) To rinse, put the on-off switch in the “off”

(0)position before pushing the adjustable fan wand nozzle inwards as shown in Figure 24. This will increase water pressure and automatically stop detergent flow. Return on-off switch to “on” (I) position.

24

7.) Rinse detergent from surface.

8.) When you have finished using the detergent dispensing system, or when changing from one detergent type to another, you must ensure the entire system has been rinsed clean. To do this, remove tank to empty remaining detergent, and rinse tank out several times with clean water. Then fill detergent tank with clean water and replace into pressure washer. Leaving the nozzle in the outward detergent pick up position as shown in figure 23, press the gun trigger for 1 minute until only clean water is sprayed. Remove tank and empty remaining water. NOTE: Failure to follow the above detergent rinsing procedure will cause the dispensing system to become clogged.

NOTE: DO NOT USE:

•Bleach, chlorine products and other corrosive chemicals.

•Liquids containing solvents (i.e., paint thinners, gasoline, oils)

•Tri-sodium phosphate products

•Ammonia products

•Acid-based products

These chemicals will harm the unit and will damage the surface being cleaned.

SURFACE PREPARATION

Before starting any cleaning task it is important to inspect the area for objects which could create a hazard. Remove objects from the area which could be tripped over such as children’s toys or outdoor

9

2.) Place power cord and garden hose into retaining clips as shown in Figures 25 & 26.

25

26

3.) Place hand on upper handle and prop foot against base of unit as shown in Fig. 27 and tilt the unit backwards.

4.) Pull unit to desired location.

5.) Remove garden hose and power cord from retaining clips.

6.) Switch unit on to continue use.

27