Briggs & Stratton 20228 Operation, How to Stop Your Pressure Washer, How to Use Accessory Tray

Page 10

Section 4: Operation

8.Start engine according to instructions given in engine owner’s manual. Also see operating instructions tag located on the pressure washer.

WARNING

Rapid retraction of starter cord (kickback) will pull hand and arm toward engine faster than you can let go.

Broken bones, fractures, bruises or sprains could result.

•When starting engine, pull cord slowly until resistance is felt and then pull rapidly to avoid kickback.

•If engine starts and fails to continue to run or if increased resistance is felt during starting pull attempts, squeeze trigger on spray gun.

NOTE: Always keep the throttle lever in the “Fast” position when operating the pressure washer.

WARNING

Running engines produce heat.Temperature of muffler and nearby areas can reach or exceed 150°F (65°C).

Severe burns can occur on contact.

Combustible debris, such as leaves, grass, brush, etc. can catch fire.

•DO NOT touch hot surfaces.

•Allow equipment to cool before touching.

•The pressure washer must be at least 5 feet from structures having combustible walls and/or other combustible materials.

•Keep at least 3 feet of clearance on all sides of pressure washer for adequate cooling, maintenance and servicing.

•In the State of California a spark arrester is required by law (Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. If you equip the muffler with a spark arrester, it must be maintained in effective working order.

How to Stop Your Pressure Washer

1.Let engine idle for two minutes.

2.Turn engine off according to instructions given in engine owner’s manual.

3.Squeeze trigger on spray gun to relieve trapped pressure in hose to avoid injury.

NOTE: A small amount of water will squirt out when pressure is released.

WARNING

The high pressure stream of water that this equipment produces can pierce skin and its underlying tissues, leading to serious injury and possible amputation.

Spray gun retains high pressure when pressure washer is shut down, which can cause injury.

•Keep high pressure hose connected to pump and spray gun while system is pressurized.

•Squeeze trigger on spray gun to relieve trapped pressure, every time you stop engine. Engage trigger lock on spray gun.

4.Engage trigger lock on spray gun when not in use.

How to Use Accessory Tray

The unit is equipped with an accessory tray with places to store your spray gun, nozzle extension, turbo nozzle, and ProjectPro™ nozzles.There is also a hook at the front of the accessory tray to hold your high pressure hose.

NOTE: The extra hole in the tray is for storing a utility brush.The brush is NOT included with your pressure washer.You can buy the brush as an optional accessory.

1.Place nozzle extension through hole on accessory tray, as shown in Figure 11.

Figure 11 — Typical Accessory Tray

2.Place spray gun through hole on accessory tray on right side of unit (Figure 11).

3.Push turbo nozzle up and into clip on accessory tray until it snaps in, as shown in Figure 11.

4.Hang high pressure hose on hook attached to accessory tray on front of tray, as shown in Figure 11.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Manual del Propietario Safety Rules Table of ContentsEquipment Description When Adding Fuel Operate pressure washer only outdoorsHigh pressure spray may damage fragile items including glass Nozzle Extension with Quick Connect Allows you Features and Controls SectionKnow Your Pressure Washer Pump equipped with Automatic Cool Down SystemAttach Handle and Accessory Tray AssemblyCarton Contents Preparing Pressure Washer for USEAssembly Add Engine Oil and FuelChecklist Before Starting Engine Connect Hose and Water Supply to PumpOperation Section HOW to USE Your Pressure WasherHow to Start Your Pressure Washer Pressure Washer LocationHow to Use Accessory Tray How to Stop Your Pressure WasherOperation How to Use ProjectPro Nozzle System Follow these instructions to change ProjectPro nozzlesCleaning and Applying Detergent How to Use the Turbo NozzleTo apply detergent follow these steps Automatic Cool Down System Cleaning Detergent Siphoning TubePressure Washer Rinsing Thermal ReliefGeneral Maintenance Recommendations Section MaintenanceSpecifications Pressure Washer MaintenanceRing Maintenance MaintenanceNozzle Maintenance Use wire hereChanging Pump Oil Engine MaintenancePump Maintenance Change pump oil as followsStoring the Engine StoragePreparing the Unit for Storage Protecting the PumpTroubleshooting TroubleshootingProblem Cause Correction Consumer Use Years Years or YearDescripción DEL Equipo Reglas de SeguridadConserve Estas Instrucciones Tabla DE Contenidos Reglas DE SeguridadSección 1 Reglas de Seguridad Cuando Añada CombustiblePrecaución Características y Controles Conozca SU Maquina Lavadora DE PresionMontaje MontajePreparando EL Lavador a Alta Presión Para SU USO Agregar Aceite al Motor y Gasolina Sección 3 MontajeColoque la lavadora a presión sobre una superficie nivelada Conecte la Manguera y el Suministro de Agua a la Bomba Lista de Revision Previa al Arranque del MotorUbicación del Lavadora a Presión OperaciónCómo Usar SU Máquina Lavadora a Presión Cómo Darle Arranque a su Máquina Lavadora a PresiónCómo Detener su Máquina Lavadora a Presión Sección 4 OperaciónUtilización de la Bandeja de Accesorios La Presión Alta Cómo Usar el Sistema de Boquillas ProjectProLa Presión Baja Coloque el pestillo de seguridad de la pistola de rociadoDetergentes caseros podrían dañar la bomba Cómo Usar la Boquilla a ChorroLimpieza y Aplicación del Detergentes Para aplicar el detergente, siga los siguientes pasosSistema de Enfriamiento Automático Alivio Térmico Enjuage de la Máquina Lavadora a PresiónLimpiando el Tubo Para EnjuageRecomendaciones Generales MantenimientoEspecificaciones Mantenimiento DE LA Maquina Lavadora a PresionMantenimiento de los Anillos O Sección 5 MantenimientoMantenimiento de la Boquilla Mantenimiento de la BombaPreparando LA Unidad Para SU Almacenamiento Sección 5 y 6 Mantenimiento y AlmacenamientoMantenimiento DEL Motor Almacenando EL MotorDiagnosticos de Averías Reparacion DE AveriasGarantía Limitada

195764GS, 20228 specifications

Briggs & Stratton is a name synonymous with reliable power and performance in small engine solutions. The Briggs & Stratton 20228,195764GS is a prime example of their commitment to innovation, durability, and efficiency. This engine is primarily designed for a variety of applications, including outdoor power equipment and generators, making it an ideal choice for both commercial and residential use.

One of the standout features of the 20228,195764GS is its robust design. Built with high-quality materials, this engine is engineered to withstand the rigors of heavy use. The construction is not only durable but also lightweight, allowing for easy maneuverability and installation. This feature proves advantageous for lawnmowers, pressure washers, and generators, ensuring they operate efficiently under various working conditions.

In terms of power, the 20228,195764GS engine delivers impressive performance, providing reliable output to tackle tough jobs with ease. With an optimized combustion system, it ensures maximum fuel efficiency while minimizing emissions. This is pivotal in meeting environmental standards while also lowering operational costs for users.

Furthermore, the engine integrates advanced technologies that enhance overall functionality. The patented ReadyStart technology simplifies the starting process, eliminating the need for manual choke adjustments. This ensures a hassle-free startup every time, making it user-friendly, especially for those new to operating similar equipment.

Another notable characteristic is the engine’s maintenance-friendly design. When servicing is required, access to components is straightforward, reducing downtime and improving user experience. Briggs & Stratton also emphasizes long-lasting performance, with features like strong air filtration systems to extend engine life by protecting it from contaminants.

The 20228,195764GS is also designed for versatility. It can power various attachments and machines, making it suitable for different tasks, from landscaping to construction purposes. Briggs & Stratton's reputation for quality and innovation is evident in this model, which reflects their commitment to meeting the diverse needs of their customers.

Overall, the Briggs & Stratton 20228,195764GS combines power, efficiency, and ease of use, making it an exceptional choice for consumers looking for a reliable engine solution. This model not only embodies the brand's legacy but also sets a standard for what modern small engines should deliver, ensuring that projects can be completed seamlessly and efficiently.
Top Page Image Contents